DMP 128
12入力8出力ProDSP™ 搭載デジタルオーディオマトリックスプロセッサー
最近閲覧した製品
DMP 128
コンサルタント向け資料
製品番号を選択してください:
テキストをコピー
コピーされました！
エラーが発生しました。しばらくしてからもう一度お試しください。
DMP 128
- Provide an audio digital signal processor that shall support 12 mono analog inputs capable of microphone or line level signals and eight mono analog line level outputs for signal routing and management.
- 12 input, eight output audio digital signal processor with digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support eight mono, microphone or line level, balanced or unbalanced signals on eight 3-pole, 3.5 mm captive screw connectors
- Shall support four mono, microphone or line level, balanced or unbalanced signals on two 6-pole, 3.5 mm captive screw connectors
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on first eight inputs
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Output Requirements
- Shall support eight mono line level, balanced or unbalanced signals on four 6-pole, 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall support 32-bit and 64-bit processing algorithms depending on process
- Shall provide a maximum, deterministic latency of 4.5 ms from input to output
- Shall provide additional, deterministic latency of 2 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 4 ms when Automixing is used
- Audio Device Requirements — Input to Output
- Shall provide a signal-to-noise ratio of greater than 105 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single window view of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass, treble and parametric EQ); Dynamics processing (AGC, compressor, limiter, noise gate); Delay processing; Ducking processor; Automixing; Loudness processor; and multiple gain stages
- Shall provide cut and paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide 32 Group Master controls for consolidation of up to 16 individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide 32 Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AEC, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Volume processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide file upload in both Live and Emulate mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Mic Open Priority and Chairman Priority modes
- Shall provide Number of Open Microphone parameter from 0 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- Control Requirements
- Shall provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN on RJ-45 connector
- Shall support bidirectional RS-232 on 3-pole, 3.5 mm captive screw connectors
- Shall support USB 2.0 control on female mini USB B connector
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232 on 3-pole, 3.5 mm captive screw connectors or Ethernet on RJ-45 connector
- Shall provide 20 digital I/O ports on 3-pole, 3.5 mm captive screw connectors for processor remote control and/or feedback to external control system or physical devices
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port on mini USB B connector
- Shall provide green LEDs for Expansion and LAN port activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for clip warning indication
- Rear Panel Requirements
- Shall provide LEDs for input channel 1 through 8 phantom power indication
- Shall provide 12 inputs on 3.5 mm captive screw connectors
- Shall provide eight outputs on 3.5 mm captive screw connectors
- Shall provide 20 digital input/output ports on 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port on 3.5 mm captive screw connector
- Shall provide Expansion port on RJ-45 connector
- Shall provide Ethernet host port on RJ-45 connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, full rack width metal enclosure
- Shall be convection-cooled
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 128, part number 60-1211-01; no alternates or equals.
- 12 input, eight output audio digital signal processor with digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
DMP 128
- Provide an audio digital signal processor that shall support 12 mono analog inputs capable of microphone or line level signals and eight mono analog line level outputs for signal routing and management.
- 12 input, eight output audio digital signal processor with digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support eight mono, microphone or line level, balanced or unbalanced signals on eight 3-pole, 3.5 mm captive screw connectors
- Shall support four mono, microphone or line level, balanced or unbalanced signals on two 6-pole, 3.5 mm captive screw connectors
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on first eight inputs
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Output Requirements
- Shall support eight mono line level, balanced or unbalanced signals on four 6-pole, 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall support 32-bit and 64-bit processing algorithms depending on process
- Shall provide a maximum, deterministic latency of 4.5 ms from input to output
- Shall provide additional, deterministic latency of 2 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 4 ms when Automixing is used
- Audio Device Requirements — Input to Output
- Shall provide a signal-to-noise ratio of greater than 105 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single window view of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass, treble and parametric EQ); Dynamics processing (AGC, compressor, limiter, noise gate); Delay processing; Ducking processor; Automixing; Loudness processor; and multiple gain stages
- Shall provide cut and paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide 32 Group Master controls for consolidation of up to 16 individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide 32 Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AEC, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Volume processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide file upload in both Live and Emulate mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Mic Open Priority and Chairman Priority modes
- Shall provide Number of Open Microphone parameter from 0 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- Control Requirements
- Shall provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN on RJ-45 connector
- Shall support bidirectional RS-232 on 3-pole, 3.5 mm captive screw connectors
- Shall support USB 2.0 control on female mini USB B connector
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232 on 3-pole, 3.5 mm captive screw connectors or Ethernet on RJ-45 connector
- Shall provide 20 digital I/O ports on 3-pole, 3.5 mm captive screw connectors for processor remote control and/or feedback to external control system or physical devices
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port on mini USB B connector
- Shall provide green LEDs for Expansion and LAN port activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for clip warning indication
- Rear Panel Requirements
- Shall provide LEDs for input channel 1 through 8 phantom power indication
- Shall provide 12 inputs on 3.5 mm captive screw connectors
- Shall provide eight outputs on 3.5 mm captive screw connectors
- Shall provide 20 digital input/output ports on 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port on 3.5 mm captive screw connector
- Shall provide Expansion port on RJ-45 connector
- Shall provide Ethernet host port on RJ-45 connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, full rack width metal enclosure
- Shall be convection-cooled
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 128, part number 60-1211-01; no alternates or equals.
- 12 input, eight output audio digital signal processor with digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
DMP 128 C P
- Provide an audio digital signal processor that shall support 12 mono analog inputs capable of microphone or line level signals and eight mono analog line level outputs for signal routing and management.
- 12 input, eight output audio digital signal processor with acoustic echo cancellation, analog telephone interface, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support eight mono, microphone or line level, balanced or unbalanced signals on eight 3-pole, 3.5 mm captive screw connectors
- Shall support four mono, microphone or line level, balanced or unbalanced signals on two 6-pole, 3.5 mm captive screw connectors
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on first eight inputs
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Output Requirements
- Shall support eight mono line level, balanced or unbalanced signals on four 6-pole, 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall support 32-bit and 64-bit processing algorithms depending on process
- Shall provide a maximum, deterministic latency 9.9 ms from input to output on inputs 1 through 8
- Shall provide a maximum, deterministic latency of 4.5 ms from input to output 9 through 12
- Shall provide additional, deterministic latency of 2 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 4 ms when Automixing is used
- Shall provide additional, deterministic latency of 16 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide a signal-to-noise ratio of greater than 105 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single window view of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass, treble and parametric EQ); AEC; Dynamics processing (AGC, compressor, limiter, noise gate); Delay processing; Ducking processor; Automixing; Loudness processor; and multiple gain stages
- Shall provide cut and paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide 32 Group Master controls for consolidation of up to 16 individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide 32 Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AEC, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Volume processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide file upload in both Live and Emulate mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Mic Open Priority and Chairman Priority modes
- Shall provide Number of Open Microphone parameter from 0 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide eight independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- Analog Telephone Interface Requirements
- Shall provide analog telephone interface to initiate and receive calls over the public switched telephone network and private branch exchange (POTS)
- Shall provide software-based telephone dialer with keypad functions, dialed number readout
- Shall support all phone features including, but not limited to: Caller ID, Call Waiting, Call Status, Call Forwarding, and Conference Calling
- Shall support multiple regions of operation including, but not limited to: USA, Canada, Europe, Australia, and Japan
- Shall provide -18 to +20 dB of Input Gain adjustment in software adjustable 0.1 dB steps
- Shall provide 0 to -100 dB of Output Attenuation adjustment in software adjustable 0.1 dB steps
- Shall provide Telephone Line port on RJ-11 connector
- Shall provide Telephone Handset port on RJ-11 connector
- Control Requirements
- Shall provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN on RJ-45 connector
- Shall support bidirectional RS-232 on 3-pole, 3.5 mm captive screw connectors
- Shall support USB 2.0 control on female mini USB B connector
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232 on 3-pole, 3.5 mm captive screw connectors or Ethernet on RJ-45 connector
- Shall provide 20 digital I/O ports on 3-pole, 3.5 mm captive screw connectors for processor remote control and/or feedback to external control system or physical devices
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port on mini USB B connector
- Shall provide green LEDs for Expansion and LAN port activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for clip warning indication
- Rear Panel Requirements
- Shall provide LEDs for input channel 1 through 8 phantom power indication
- Shall provide 12 inputs on 3.5 mm captive screw connectors
- Shall provide eight outputs on 3.5 mm captive screw connectors
- Shall provide 20 digital input/output ports on 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port on 3.5 mm captive screw connector
- Shall provide Expansion port on RJ-45 connector
- Shall provide Ethernet host port on RJ-45 connector
- Shall provide Telephone Line port on RJ-11 connector
- Shall provide Telephone Handset port on RJ-11 connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, full rack width metal enclosure
- Shall be fan-cooled with right to left airflow
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 128 C P, part number 60-1179-01; no alternates or equals.
- 12 input, eight output audio digital signal processor with acoustic echo cancellation, analog telephone interface, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
DMP 128 C P
- Provide an audio digital signal processor that shall support 12 mono analog inputs capable of microphone or line level signals and eight mono analog line level outputs for signal routing and management.
- 12 input, eight output audio digital signal processor with acoustic echo cancellation, analog telephone interface, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support eight mono, microphone or line level, balanced or unbalanced signals on eight 3-pole, 3.5 mm captive screw connectors
- Shall support four mono, microphone or line level, balanced or unbalanced signals on two 6-pole, 3.5 mm captive screw connectors
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on first eight inputs
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Output Requirements
- Shall support eight mono line level, balanced or unbalanced signals on four 6-pole, 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall support 32-bit and 64-bit processing algorithms depending on process
- Shall provide a maximum, deterministic latency 9.9 ms from input to output on inputs 1 through 8
- Shall provide a maximum, deterministic latency of 4.5 ms from input to output 9 through 12
- Shall provide additional, deterministic latency of 2 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 4 ms when Automixing is used
- Shall provide additional, deterministic latency of 16 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide a signal-to-noise ratio of greater than 105 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single window view of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass, treble and parametric EQ); AEC; Dynamics processing (AGC, compressor, limiter, noise gate); Delay processing; Ducking processor; Automixing; Loudness processor; and multiple gain stages
- Shall provide cut and paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide 32 Group Master controls for consolidation of up to 16 individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide 32 Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AEC, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Volume processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide file upload in both Live and Emulate mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Mic Open Priority and Chairman Priority modes
- Shall provide Number of Open Microphone parameter from 0 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide eight independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- Analog Telephone Interface Requirements
- Shall provide analog telephone interface to initiate and receive calls over the public switched telephone network and private branch exchange (POTS)
- Shall provide software-based telephone dialer with keypad functions, dialed number readout
- Shall support all phone features including, but not limited to: Caller ID, Call Waiting, Call Status, Call Forwarding, and Conference Calling
- Shall support multiple regions of operation including, but not limited to: USA, Canada, Europe, Australia, and Japan
- Shall provide -18 to +20 dB of Input Gain adjustment in software adjustable 0.1 dB steps
- Shall provide 0 to -100 dB of Output Attenuation adjustment in software adjustable 0.1 dB steps
- Shall provide Telephone Line port on RJ-11 connector
- Shall provide Telephone Handset port on RJ-11 connector
- Control Requirements
- Shall provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN on RJ-45 connector
- Shall support bidirectional RS-232 on 3-pole, 3.5 mm captive screw connectors
- Shall support USB 2.0 control on female mini USB B connector
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232 on 3-pole, 3.5 mm captive screw connectors or Ethernet on RJ-45 connector
- Shall provide 20 digital I/O ports on 3-pole, 3.5 mm captive screw connectors for processor remote control and/or feedback to external control system or physical devices
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port on mini USB B connector
- Shall provide green LEDs for Expansion and LAN port activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for clip warning indication
- Rear Panel Requirements
- Shall provide LEDs for input channel 1 through 8 phantom power indication
- Shall provide 12 inputs on 3.5 mm captive screw connectors
- Shall provide eight outputs on 3.5 mm captive screw connectors
- Shall provide 20 digital input/output ports on 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port on 3.5 mm captive screw connector
- Shall provide Expansion port on RJ-45 connector
- Shall provide Ethernet host port on RJ-45 connector
- Shall provide Telephone Line port on RJ-11 connector
- Shall provide Telephone Handset port on RJ-11 connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, full rack width metal enclosure
- Shall be fan-cooled with right to left airflow
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 128 C P, part number 60-1179-01; no alternates or equals.
- 12 input, eight output audio digital signal processor with acoustic echo cancellation, analog telephone interface, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
DMP 128 C P AT
- Provide an audio digital signal processor that shall support 12 mono analog inputs capable of microphone or line level signals and eight mono analog line level outputs for signal routing and management.
- 12 input, eight output audio digital signal processor with acoustic echo cancellation, analog telephone interface, Dante™ audio networking, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support eight mono, microphone or line level, balanced or unbalanced signals on eight 3-pole, 3.5 mm captive screw connectors
- Shall support four mono, microphone or line level, balanced or unbalanced signals on two 6-pole, 3.5 mm captive screw connectors
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on first eight inputs
- Shall provide option to select an alternate digital input from the Dante audio network on mic/line inputs 1 to 8
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Output Requirements
- Shall support eight mono line level, balanced or unbalanced signals on four, 6-pole, 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall support 32-bit and 64-bit processing algorithms depending on process
- Shall provide a maximum, deterministic latency 9.9 ms from input to output on inputs 1 through 8
- Shall provide a maximum, deterministic latency of 4.5 ms from input to output 9 through 12
- Shall provide additional, deterministic latency of 2 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 4 ms when Automixing is used
- Shall provide additional, deterministic latency of 16 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide a signal-to-noise ratio of greater than 105 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single window view of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass, treble and parametric EQ); AEC; Dynamics processing (AGC, compressor, limiter, noise gate); Delay processing; Ducking processor; Automixing; Loudness processor; and multiple gain stages
- Shall provide cut and paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide 32 Group Master controls for consolidation of up to 16 individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide 32 Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AEC, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Volume processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide file upload in both Live and Emulate mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Mic Open Priority and Chairman Priority modes
- Shall provide Number of Open Microphone parameter from 0 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide eight independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- Analog Telephone Interface Requirements
- Shall provide analog telephone interface to initiate and receive calls over the public switched telephone network and private branch exchange (POTS)
- Shall provide software-based telephone dialer with keypad functions, dialed number readout
- Shall support all phone features including, but not limited to: Caller ID, Call Waiting, Call Status, Call Forwarding, and Conference Calling
- Shall support multiple regions of operation including, but not limited to: USA, Canada, Europe, Australia, and Japan
- Shall provide -18 to +20 dB of Input Gain adjustment in software adjustable 0.1 dB steps
- Shall provide 0 to -100 dB of Output Attenuation adjustment in software adjustable 0.1 dB steps
- Shall provide Telephone Line port on RJ-11 connector
- Shall provide Telephone Handset port on RJ-11 connector
- Dante Audio Networking Requirements
- Shall support 56 incoming channels and 24 outgoing channels over a local area network using standard Internet protocols
- Eight incoming channels may be rerouted to input channel processing, replacing the analog input
- Shall support primary and redundant Dante audio networks
- Shall support Dante Controller software for digital audio network configuration
- Shall provide an internal four-port Gigabit switch on RJ-45 connectors to support Dante audio network connection and direct interconnection between Dante-enabled products
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Shall provide selectable 0.25 ms, 1.0 ms (default) or 5.0 ms of deterministic latency
- Shall support IEEE 802.1 Audio Video Bridging technical standards upon ratification
- Shall support 56 incoming channels and 24 outgoing channels over a local area network using standard Internet protocols
- Control Requirements
- Shall provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN on RJ-45 connector
- Shall support bidirectional RS-232 on 3-pole, 3.5 mm captive screw connectors
- Shall support USB 2.0 control on female mini USB B connector
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232 on 3-pole, 3.5 mm captive screw connectors or Ethernet on RJ-45 connector
- Shall provide 20 digital I/O ports on 3-pole, 3.5 mm captive screw connectors for processor remote control and/or feedback to external control system or physical devices
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port on mini USB B connector
- Shall provide green LEDs for Expansion and LAN port activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for clip warning indication
- Rear Panel Requirements
- Shall provide LEDs for input channel 1 through 8 phantom power indication
- Shall provide 12 inputs on 3.5 mm captive screw connectors
- Shall provide eight outputs on 3.5 mm captive screw connectors
- Shall provide 20 digital input/output ports on 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port on 3.5 mm captive screw connector
- Shall provide Expansion port on RJ-45 connector
- Shall provide Ethernet host port on RJ-45 connector
- Shall provide an internal four-port Gigabit switch on RJ-45 connectors to support Dante audio network connection and direct interconnection between Dante-enabled products
- Shall provide Telephone Line port on RJ-11 connector
- Shall provide Telephone Handset port on RJ-11 connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, full rack width metal enclosure
- Shall be fan-cooled with right to left airflow
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 128 C P AT, part number 60-1179-10; no alternates or equals.
- 12 input, eight output audio digital signal processor with acoustic echo cancellation, analog telephone interface, Dante™ audio networking, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
DMP 128 C P AT
- Provide an audio digital signal processor that shall support 12 mono analog inputs capable of microphone or line level signals and eight mono analog line level outputs for signal routing and management.
- 12 input, eight output audio digital signal processor with acoustic echo cancellation, analog telephone interface, Dante™ audio networking, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support eight mono, microphone or line level, balanced or unbalanced signals on eight 3-pole, 3.5 mm captive screw connectors
- Shall support four mono, microphone or line level, balanced or unbalanced signals on two 6-pole, 3.5 mm captive screw connectors
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on first eight inputs
- Shall provide option to select an alternate digital input from the Dante audio network on mic/line inputs 1 to 8
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Output Requirements
- Shall support eight mono line level, balanced or unbalanced signals on four, 6-pole, 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall support 32-bit and 64-bit processing algorithms depending on process
- Shall provide a maximum, deterministic latency 9.9 ms from input to output on inputs 1 through 8
- Shall provide a maximum, deterministic latency of 4.5 ms from input to output 9 through 12
- Shall provide additional, deterministic latency of 2 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 4 ms when Automixing is used
- Shall provide additional, deterministic latency of 16 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide a signal-to-noise ratio of greater than 105 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single window view of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass, treble and parametric EQ); AEC; Dynamics processing (AGC, compressor, limiter, noise gate); Delay processing; Ducking processor; Automixing; Loudness processor; and multiple gain stages
- Shall provide cut and paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide 32 Group Master controls for consolidation of up to 16 individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide 32 Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AEC, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Volume processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide file upload in both Live and Emulate mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Mic Open Priority and Chairman Priority modes
- Shall provide Number of Open Microphone parameter from 0 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide eight independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- Analog Telephone Interface Requirements
- Shall provide analog telephone interface to initiate and receive calls over the public switched telephone network and private branch exchange (POTS)
- Shall provide software-based telephone dialer with keypad functions, dialed number readout
- Shall support all phone features including, but not limited to: Caller ID, Call Waiting, Call Status, Call Forwarding, and Conference Calling
- Shall support multiple regions of operation including, but not limited to: USA, Canada, Europe, Australia, and Japan
- Shall provide -18 to +20 dB of Input Gain adjustment in software adjustable 0.1 dB steps
- Shall provide 0 to -100 dB of Output Attenuation adjustment in software adjustable 0.1 dB steps
- Shall provide Telephone Line port on RJ-11 connector
- Shall provide Telephone Handset port on RJ-11 connector
- Dante Audio Networking Requirements
- Shall support 56 incoming channels and 24 outgoing channels over a local area network using standard Internet protocols
- Eight incoming channels may be rerouted to input channel processing, replacing the analog input
- Shall support primary and redundant Dante audio networks
- Shall support Dante Controller software for digital audio network configuration
- Shall provide an internal four-port Gigabit switch on RJ-45 connectors to support Dante audio network connection and direct interconnection between Dante-enabled products
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Shall provide selectable 0.25 ms, 1.0 ms (default) or 5.0 ms of deterministic latency
- Shall support IEEE 802.1 Audio Video Bridging technical standards upon ratification
- Shall support 56 incoming channels and 24 outgoing channels over a local area network using standard Internet protocols
- Control Requirements
- Shall provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN on RJ-45 connector
- Shall support bidirectional RS-232 on 3-pole, 3.5 mm captive screw connectors
- Shall support USB 2.0 control on female mini USB B connector
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232 on 3-pole, 3.5 mm captive screw connectors or Ethernet on RJ-45 connector
- Shall provide 20 digital I/O ports on 3-pole, 3.5 mm captive screw connectors for processor remote control and/or feedback to external control system or physical devices
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port on mini USB B connector
- Shall provide green LEDs for Expansion and LAN port activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for clip warning indication
- Rear Panel Requirements
- Shall provide LEDs for input channel 1 through 8 phantom power indication
- Shall provide 12 inputs on 3.5 mm captive screw connectors
- Shall provide eight outputs on 3.5 mm captive screw connectors
- Shall provide 20 digital input/output ports on 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port on 3.5 mm captive screw connector
- Shall provide Expansion port on RJ-45 connector
- Shall provide Ethernet host port on RJ-45 connector
- Shall provide an internal four-port Gigabit switch on RJ-45 connectors to support Dante audio network connection and direct interconnection between Dante-enabled products
- Shall provide Telephone Line port on RJ-11 connector
- Shall provide Telephone Handset port on RJ-11 connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, full rack width metal enclosure
- Shall be fan-cooled with right to left airflow
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 128 C P AT, part number 60-1179-10; no alternates or equals.
- 12 input, eight output audio digital signal processor with acoustic echo cancellation, analog telephone interface, Dante™ audio networking, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, and 24-bit/48 kHz audio converters
アイテムをカートに追加する
Order Message Number
製品番号
注: Extron products using the Universal AC Outlet accept a number of different AC plug types. Before use, ensure that the device meets all regulatory requirements for your region and complies with all applicable local safety and electrical codes and standards.
現在の合計金額:
Annotation Graphics Processor
To view this page ensure that Adobe Flash Player version
11.0.0 or greater is installed and enabled.
Chrome
Firefox
Edge
Safari