DMP 64 Plus
6x4 ProDSPデジタルオーディオマトリックスプロセッサー
最近閲覧した製品
DMP 64 Plus
コンサルタント向け資料
製品番号��選択してください:
テキストをコピー
コピーされました！
エラーが発生しました。しばらくしてからもう一度お試しください。
DMP 64 Plus C
- Provide an audio digital matrix processor that shall support 6 mono analog inputs capable of microphone or line level signals and 4 mono analog line level outputs for signal routing and management.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Microphone level
- Line level, balanced or unbalanced
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on the six analog inputs
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Output Requirements
- Shall support four mono line level, balanced or unbalanced outputs that accept 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall provide a mix matrix such that all inputs and returns can be discretely routed to any or all of the outputs or sends
- Shall provide 6 DSP channels with acoustic echo cancellation
- Shall provide a maximum, deterministic latency of 3.2 ms from input to output
- Shall provide additional, deterministic latency of 1.3 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 12 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide an analog in to analog out signal-to-noise ratio of greater than 107 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single, scrollable window for viewing of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass shelving, treble shelving, parametric, dynamic loudness, and notch EQ); Dynamics processing (AGC, Compressor, Limiter, Noise Gate); Delay processing; Ducking and Adaptive Gain processing; Feedback Suppressor processing, Automixing; and multiple gain stages
- Shall provide cut, copy, paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, aux inputs, aux outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide Group Master controls for consolidation of individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Attenuation processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide configuration file upload in Live mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Aux Input/Output Requirements
- Shall provide a total of 8 Aux Inputs to be configured with a combination of file players and USB audio connections.
- Shall provide a total of 8 Aux Outputs, assignable to USB audio connections.
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors at sub-millisecond latency
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Open Mic Priority and Chairman Priority modes
- Shall provide Max Number of Open Microphone parameter from 1 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide six independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- Control Requirements
- Shall accept an RJ-45 connector to provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN
- Shall accept 3.5 mm captive screw connectors to support bidirectional RS-232
- Shall provide an ACP audio control port to support the use of Extron Audio Control Panels.
- Shall provide a female USB mini type B port for software control
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232, Ethernet, or USB
- Shall provide 6 sets of 2 configurable digital I/O ports that accept 3.5 mm captive screw connectors and can be programmed to sense and then respond to external triggers
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port that accepts a USB mini type B connector
- Shall provide green LEDs for Expansion port, LAN port, and USB audio interface activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for input and output clip warning indication
- Rear Panel Requirements
- Shall provide 6 inputs that accept 3.5 mm captive screw connectors
- Shall provide 4 outputs that accept 3.5 mm captive screw connectors
- Shall provide a digital audio interface on a mini USB B port
- Shall provide 6 digital input and 6 digital output ports that accept 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port that accepts a 3.5 mm captive screw connector
- Shall provide Expansion port that accepts an RJ-45 connector
- Shall provide Ethernet host port that accepts an RJ-45 connector
- Shall provide an ACP audio control port that accepts a 3.5 mm captive screw connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, half rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 64 Plus C, part number 60-1823-01; no alternates or equals.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
DMP 64 Plus C
- Provide an audio digital matrix processor that shall support 6 mono analog inputs capable of microphone or line level signals and 4 mono analog line level outputs for signal routing and management.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Microphone level
- Line level, balanced or unbalanced
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on the six analog inputs
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Output Requirements
- Shall support four mono line level, balanced or unbalanced outputs that accept 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall provide a mix matrix such that all inputs and returns can be discretely routed to any or all of the outputs or sends
- Shall provide 6 DSP channels with acoustic echo cancellation
- Shall provide a maximum, deterministic latency of 3.2 ms from input to output
- Shall provide additional, deterministic latency of 1.3 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 12 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide an analog in to analog out signal-to-noise ratio of greater than 107 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single, scrollable window for viewing of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass shelving, treble shelving, parametric, dynamic loudness, and notch EQ); Dynamics processing (AGC, Compressor, Limiter, Noise Gate); Delay processing; Ducking and Adaptive Gain processing; Feedback Suppressor processing, Automixing; and multiple gain stages
- Shall provide cut, copy, paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, aux inputs, aux outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide Group Master controls for consolidation of individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Attenuation processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide configuration file upload in Live mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Aux Input/Output Requirements
- Shall provide a total of 8 Aux Inputs to be configured with a combination of file players and USB audio connections.
- Shall provide a total of 8 Aux Outputs, assignable to USB audio connections.
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors at sub-millisecond latency
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Open Mic Priority and Chairman Priority modes
- Shall provide Max Number of Open Microphone parameter from 1 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide six independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- Control Requirements
- Shall accept an RJ-45 connector to provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN
- Shall accept 3.5 mm captive screw connectors to support bidirectional RS-232
- Shall provide an ACP audio control port to support the use of Extron Audio Control Panels.
- Shall provide a female USB mini type B port for software control
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232, Ethernet, or USB
- Shall provide 6 sets of 2 configurable digital I/O ports that accept 3.5 mm captive screw connectors and can be programmed to sense and then respond to external triggers
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port that accepts a USB mini type B connector
- Shall provide green LEDs for Expansion port, LAN port, and USB audio interface activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for input and output clip warning indication
- Rear Panel Requirements
- Shall provide 6 inputs that accept 3.5 mm captive screw connectors
- Shall provide 4 outputs that accept 3.5 mm captive screw connectors
- Shall provide a digital audio interface on a mini USB B port
- Shall provide 6 digital input and 6 digital output ports that accept 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port that accepts a 3.5 mm captive screw connector
- Shall provide Expansion port that accepts an RJ-45 connector
- Shall provide Ethernet host port that accepts an RJ-45 connector
- Shall provide an ACP audio control port that accepts a 3.5 mm captive screw connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, half rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 64 Plus C, part number 60-1823-01; no alternates or equals.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
DMP 64 Plus C AT
- Provide an audio digital matrix processor that shall support 6 mono analog inputs capable of microphone or line level signals and 4 mono analog line level outputs for signal routing and management.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, 32x16 Dante™ audio networking, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Microphone level
- Line level, balanced or unbalanced
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on the six analog inputs
- Shall provide option to select an alternate input from the Dante audio network or EXP input on mic/line inputs 1 to 6
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Output Requirements
- Shall support four mono line level, balanced or unbalanced outputs that accept 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall provide a mix matrix such that all inputs and returns can be discretely routed to any or all of the outputs or sends
- Shall provide 6 DSP channels with acoustic echo cancellation
- Shall provide a maximum, deterministic latency of 3.2 ms from input to output
- Shall provide additional, deterministic latency of 1.3 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 12 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide an analog in to analog out signal-to-noise ratio of greater than 107 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single, scrollable window for viewing of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass shelving, treble shelving, parametric, dynamic loudness, and notch EQ); Dynamics processing (AGC, Compressor, Limiter, Noise Gate); Delay processing; Ducking and Adaptive Gain processing; Feedback Suppressor processing, Automixing; and multiple gain stages
- Shall provide cut, copy, paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, aux inputs, aux outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide Group Master controls for consolidation of individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Attenuation processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide configuration file upload in Live mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Aux Input/Output Requirements
- Shall provide a total of 8 Aux Inputs to be configured with a combination of file players and USB audio connections.
- Shall provide a total of 8 Aux Outputs, assignable to USB audio connections.
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors at sub-millisecond latency
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Open Mic Priority and Chairman Priority modes
- Shall provide Max Number of Open Microphone parameter from 1 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide six independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- Dante Audio Networking Requirements
- Shall support 32 incoming channels and 16 outgoing channels over a local area network using standard Internet protocols
- Twelve incoming channels may be rerouted to input channel processing
- Shall support primary and redundant Dante audio networks
- Shall support Dante Controller software for digital audio network configuration
- Shall provide an internal four-port Gigabit switch on RJ-45 connectors to support Dante audio network connection and direct interconnection between Dante-enabled products
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Shall provide selectable 0.25 ms, 0.50 ms, 1.0 ms (default), 2.0 ms, or 5.0 ms of deterministic latency
- Shall support 32 incoming channels and 16 outgoing channels over a local area network using standard Internet protocols
- Control Requirements
- Shall accept an RJ-45 connector to provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN
- Shall accept 3.5 mm captive screw connectors to support bidirectional RS-232
- Shall provide an ACP audio control port to support the use of Extron Audio Control Panels.
- Shall provide a female USB mini type B port for software control
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232, Ethernet, or USB
- Shall provide 6 sets of 2 configurable digital I/O ports that accept 3.5 mm captive screw connectors and can be programmed to sense and then respond to external triggers
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port that accepts a USB mini type B connector
- Shall provide green LEDs for Expansion port, LAN port, and USB audio interface activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for input and output clip warning indication
- Rear Panel Requirements
- Shall provide 6 inputs that accept 3.5 mm captive screw connectors
- Shall provide 4 outputs that accept 3.5 mm captive screw connectors
- Shall provide a digital audio interface on a mini USB B port
- Shall provide 6 digital input and 6 digital output ports that accept 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port that accepts a 3.5 mm captive screw connector
- Shall provide Expansion port that accepts an RJ-45 connector
- Shall provide Ethernet host port that accepts an RJ-45 connector
- Shall provide an ACP audio control port that accepts a 3.5 mm captive screw connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, half rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 64 Plus C AT, part number 60-1823-10; no alternates or equals.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, 32x16 Dante™ audio networking, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
DMP 64 Plus C AT
- Provide an audio digital matrix processor that shall support 6 mono analog inputs capable of microphone or line level signals and 4 mono analog line level outputs for signal routing and management.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, 32x16 Dante™ audio networking, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Microphone level
- Line level, balanced or unbalanced
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on the six analog inputs
- Shall provide option to select an alternate input from the Dante audio network or EXP input on mic/line inputs 1 to 6
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Output Requirements
- Shall support four mono line level, balanced or unbalanced outputs that accept 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall provide a mix matrix such that all inputs and returns can be discretely routed to any or all of the outputs or sends
- Shall provide 6 DSP channels with acoustic echo cancellation
- Shall provide a maximum, deterministic latency of 3.2 ms from input to output
- Shall provide additional, deterministic latency of 1.3 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 12 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide an analog in to analog out signal-to-noise ratio of greater than 107 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single, scrollable window for viewing of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass shelving, treble shelving, parametric, dynamic loudness, and notch EQ); Dynamics processing (AGC, Compressor, Limiter, Noise Gate); Delay processing; Ducking and Adaptive Gain processing; Feedback Suppressor processing, Automixing; and multiple gain stages
- Shall provide cut, copy, paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, aux inputs, aux outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide Group Master controls for consolidation of individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Attenuation processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide configuration file upload in Live mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Aux Input/Output Requirements
- Shall provide a total of 8 Aux Inputs to be configured with a combination of file players and USB audio connections.
- Shall provide a total of 8 Aux Outputs, assignable to USB audio connections.
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors at sub-millisecond latency
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Open Mic Priority and Chairman Priority modes
- Shall provide Max Number of Open Microphone parameter from 1 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide six independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- Dante Audio Networking Requirements
- Shall support 32 incoming channels and 16 outgoing channels over a local area network using standard Internet protocols
- Twelve incoming channels may be rerouted to input channel processing
- Shall support primary and redundant Dante audio networks
- Shall support Dante Controller software for digital audio network configuration
- Shall provide an internal four-port Gigabit switch on RJ-45 connectors to support Dante audio network connection and direct interconnection between Dante-enabled products
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Shall provide selectable 0.25 ms, 0.50 ms, 1.0 ms (default), 2.0 ms, or 5.0 ms of deterministic latency
- Shall support 32 incoming channels and 16 outgoing channels over a local area network using standard Internet protocols
- Control Requirements
- Shall accept an RJ-45 connector to provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN
- Shall accept 3.5 mm captive screw connectors to support bidirectional RS-232
- Shall provide an ACP audio control port to support the use of Extron Audio Control Panels.
- Shall provide a female USB mini type B port for software control
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232, Ethernet, or USB
- Shall provide 6 sets of 2 configurable digital I/O ports that accept 3.5 mm captive screw connectors and can be programmed to sense and then respond to external triggers
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port that accepts a USB mini type B connector
- Shall provide green LEDs for Expansion port, LAN port, and USB audio interface activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for input and output clip warning indication
- Rear Panel Requirements
- Shall provide 6 inputs that accept 3.5 mm captive screw connectors
- Shall provide 4 outputs that accept 3.5 mm captive screw connectors
- Shall provide a digital audio interface on a mini USB B port
- Shall provide 6 digital input and 6 digital output ports that accept 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port that accepts a 3.5 mm captive screw connector
- Shall provide Expansion port that accepts an RJ-45 connector
- Shall provide Ethernet host port that accepts an RJ-45 connector
- Shall provide an ACP audio control port that accepts a 3.5 mm captive screw connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, half rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 64 Plus C AT, part number 60-1823-10; no alternates or equals.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, 32x16 Dante™ audio networking, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
DMP 64 Plus C V
- Provide an audio digital matrix processor that shall support 6 mono analog inputs capable of microphone or line level signals and 4 mono analog line level outputs for signal routing and management.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, VoIP support, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Microphone level
- Line level, balanced or unbalanced
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on the six analog inputs
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Output Requirements
- Shall support four mono line level, balanced or unbalanced outputs that accept 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall provide a mix matrix such that all inputs and returns can be discretely routed to any or all of the outputs or sends
- Shall provide 6 DSP channels with acoustic echo cancellation
- Shall provide a maximum, deterministic latency of 3.2 ms from input to output
- Shall provide additional, deterministic latency of 1.3 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 12 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide an analog in to analog out signal-to-noise ratio of greater than 107 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single, scrollable window for viewing of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass shelving, treble shelving, parametric, dynamic loudness, and notch EQ); Dynamics processing (AGC, Compressor, Limiter, Noise Gate); Delay processing; Ducking and Adaptive Gain processing; Feedback Suppressor processing, Automixing; and multiple gain stages
- Shall provide cut, copy, paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, aux inputs, aux outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide Group Master controls for consolidation of individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Attenuation processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide configuration file upload in Live mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Aux Input/Output Requirements
- Shall provide a total of 8 Aux Inputs to be configured with a combination of file players, VoIP appearances, and USB audio connections.
- Shall provide a total of 8 Aux Outputs, assignable to USB audio connections.
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors at sub-millisecond latency
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Open Mic Priority and Chairman Priority modes
- Shall provide Max Number of Open Microphone parameter from 1 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide six independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- VoIP Requirements
- Shall provide up to eight VoIP lines based on RFC 3261 of the Session Initiation Protocol (SIP 2.0)
- Shall allow customizable assignment of auxiliary channels in order to support multiple call appearances for local conferencing applications
- Shall provide independent audio processing and control per call appearance
- Shall support the following audio codecs, with selectable priority:
- G.711u (PCM u)
- G.711a (PCM a)
- G.722
- G.722.1 24/32
- G.722.1c 24/32/48
- G.726 16/24/32/40
- G.726 AAL-2 16/24/32/40
- G.729A
- Shall support VoIP configuration via an onboard webpage that includes SIP transaction logging, packet count, and network jitter
- Shall provide selection of LAN 1 or LAN 2 as the VoIP Network Interface
- Shall provide the ability to be controlled via LAN 1 or LAN 2
- Shall support VLAN tagging on either LAN 1 or LAN 2, using the 802.11Q protocol
- Shall support Quality of Service – QoS for Layer 2 and Layer 3
- Shall support Transport Layer Security – TLS and Secure Real-Time Transport Protocol – SRTP
- Shall support NAT Traversal via STUN, TURN, and ICE
- Shall support Link Layer Discovery Protocol – Media Endpoint Discovery – LLDP-MED
- Control Requirements
- Shall accept an RJ-45 connector to provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN
- Shall accept 3.5 mm captive screw connectors to support bidirectional RS-232
- Shall provide an ACP audio control port to support the use of Extron Audio Control Panels.
- Shall provide a female USB mini type B port for software control
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232, Ethernet, or USB
- Shall provide 6 sets of 2 configurable digital I/O ports that accept 3.5 mm captive screw connectors and can be programmed to sense and then respond to external triggers
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port that accepts a USB mini type B connector
- Shall provide green LEDs for Expansion port, LAN ports, and USB audio interface activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for input and output clip warning indication
- Rear Panel Requirements
- Shall provide 6 inputs that accept 3.5 mm captive screw connectors
- Shall provide 4 outputs that accept 3.5 mm captive screw connectors
- Shall provide a digital audio interface on a mini USB B port
- Shall provide 6 digital input and 6 digital output ports that accept 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port that accepts a 3.5 mm captive screw connector
- Shall provide Expansion port that accepts an RJ-45 connector
- Shall provide Ethernet host port that accepts an RJ-45 connector
- Shall provide an ACP audio control port that accepts a 3.5 mm captive screw connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, half rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 64 Plus C V, part number 60-1824-01; no alternates or equals.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, VoIP support, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
DMP 64 Plus C V
- Provide an audio digital matrix processor that shall support 6 mono analog inputs capable of microphone or line level signals and 4 mono analog line level outputs for signal routing and management.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, VoIP support, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Microphone level
- Line level, balanced or unbalanced
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on the six analog inputs
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Output Requirements
- Shall support four mono line level, balanced or unbalanced outputs that accept 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall provide a mix matrix such that all inputs and returns can be discretely routed to any or all of the outputs or sends
- Shall provide 6 DSP channels with acoustic echo cancellation
- Shall provide a maximum, deterministic latency of 3.2 ms from input to output
- Shall provide additional, deterministic latency of 1.3 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 12 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide an analog in to analog out signal-to-noise ratio of greater than 107 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single, scrollable window for viewing of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass shelving, treble shelving, parametric, dynamic loudness, and notch EQ); Dynamics processing (AGC, Compressor, Limiter, Noise Gate); Delay processing; Ducking and Adaptive Gain processing; Feedback Suppressor processing, Automixing; and multiple gain stages
- Shall provide cut, copy, paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, aux inputs, aux outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide Group Master controls for consolidation of individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Attenuation processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide configuration file upload in Live mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Aux Input/Output Requirements
- Shall provide a total of 8 Aux Inputs to be configured with a combination of file players, VoIP appearances, and USB audio connections.
- Shall provide a total of 8 Aux Outputs, assignable to USB audio connections.
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors at sub-millisecond latency
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Open Mic Priority and Chairman Priority modes
- Shall provide Max Number of Open Microphone parameter from 1 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide six independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- VoIP Requirements
- Shall provide up to eight VoIP lines based on RFC 3261 of the Session Initiation Protocol (SIP 2.0)
- Shall allow customizable assignment of auxiliary channels in order to support multiple call appearances for local conferencing applications
- Shall provide independent audio processing and control per call appearance
- Shall support the following audio codecs, with selectable priority:
- G.711u (PCM u)
- G.711a (PCM a)
- G.722
- G.722.1 24/32
- G.722.1c 24/32/48
- G.726 16/24/32/40
- G.726 AAL-2 16/24/32/40
- G.729A
- Shall support VoIP configuration via an onboard webpage that includes SIP transaction logging, packet count, and network jitter
- Shall provide selection of LAN 1 or LAN 2 as the VoIP Network Interface
- Shall provide the ability to be controlled via LAN 1 or LAN 2
- Shall support VLAN tagging on either LAN 1 or LAN 2, using the 802.11Q protocol
- Shall support Quality of Service – QoS for Layer 2 and Layer 3
- Shall support Transport Layer Security – TLS and Secure Real-Time Transport Protocol – SRTP
- Shall support NAT Traversal via STUN, TURN, and ICE
- Shall support Link Layer Discovery Protocol – Media Endpoint Discovery – LLDP-MED
- Control Requirements
- Shall accept an RJ-45 connector to provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN
- Shall accept 3.5 mm captive screw connectors to support bidirectional RS-232
- Shall provide an ACP audio control port to support the use of Extron Audio Control Panels.
- Shall provide a female USB mini type B port for software control
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232, Ethernet, or USB
- Shall provide 6 sets of 2 configurable digital I/O ports that accept 3.5 mm captive screw connectors and can be programmed to sense and then respond to external triggers
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port that accepts a USB mini type B connector
- Shall provide green LEDs for Expansion port, LAN ports, and USB audio interface activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for input and output clip warning indication
- Rear Panel Requirements
- Shall provide 6 inputs that accept 3.5 mm captive screw connectors
- Shall provide 4 outputs that accept 3.5 mm captive screw connectors
- Shall provide a digital audio interface on a mini USB B port
- Shall provide 6 digital input and 6 digital output ports that accept 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port that accepts a 3.5 mm captive screw connector
- Shall provide Expansion port that accepts an RJ-45 connector
- Shall provide Ethernet host port that accepts an RJ-45 connector
- Shall provide an ACP audio control port that accepts a 3.5 mm captive screw connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, half rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 64 Plus C V, part number 60-1824-01; no alternates or equals.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, VoIP support, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
DMP 64 Plus C V AT
- Provide an audio digital matrix processor that shall support 6 mono analog inputs capable of microphone or line level signals and 4 mono analog line level outputs for signal routing and management.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, 32x16 Dante™ audio networking, VoIP support, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Microphone level
- Line level, balanced or unbalanced
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on the six analog inputs
- Shall provide option to select an alternate input from the Dante audio network or EXP input on mic/line inputs 1 to 6
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Output Requirements
- Shall support four mono line level, balanced or unbalanced outputs that accept 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall provide a mix matrix such that all inputs and returns can be discretely routed to any or all of the outputs or sends
- Shall provide 6 DSP channels with acoustic echo cancellation
- Shall provide a maximum, deterministic latency of 3.2 ms from input to output
- Shall provide additional, deterministic latency of 1.3 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 12 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide an analog in to analog out signal-to-noise ratio of greater than 107 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single, scrollable window for viewing of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass shelving, treble shelving, parametric, dynamic loudness, and notch EQ); Dynamics processing (AGC, Compressor, Limiter, Noise Gate); Delay processing; Ducking and Adaptive Gain processing; Feedback Suppressor processing, Automixing; and multiple gain stages
- Shall provide cut, copy, paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, aux inputs, aux outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide Group Master controls for consolidation of individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Attenuation processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide configuration file upload in Live mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Aux Input/Output Requirements
- Shall provide a total of 8 Aux Inputs to be configured with a combination of file players, VoIP appearances, and USB audio connections.
- Shall provide a total of 8 Aux Outputs, assignable to USB audio connections.
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors at sub-millisecond latency
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Open Mic Priority and Chairman Priority modes
- Shall provide Max Number of Open Microphone parameter from 1 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide six independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- VoIP Requirements
- Shall provide up to eight VoIP lines based on RFC 3261 of the Session Initiation Protocol (SIP 2.0)
- Shall allow customizable assignment of auxiliary channels in order to support multiple call appearances for local conferencing applications
- Shall provide independent audio processing and control per call appearance
- Shall support the following audio codecs, with selectable priority:
- G.711u (PCM u)
- G.711a (PCM a)
- G.722
- G.722.1 24/32
- G.722.1c 24/32/48
- G.726 16/24/32/40
- G.726 AAL-2 16/24/32/40
- G.729A
- Shall support VoIP configuration via an onboard webpage that includes SIP transaction logging, packet count, and network jitter
- Shall provide selection of LAN 1 or LAN 2 as the VoIP Network Interface
- Shall provide the ability to be controlled via LAN 1 or LAN 2
- Shall support VLAN tagging on either LAN 1 or LAN 2, using the 802.11Q protocol
- Shall support Quality of Service – QoS for Layer 2 and Layer 3
- Shall support Transport Layer Security – TLS and Secure Real-Time Transport Protocol – SRTP
- Shall support NAT Traversal via STUN, TURN, and ICE
- Shall support Link Layer Discovery Protocol – Media Endpoint Discovery – LLDP-MED
- Dante Audio Networking Requirements
- Shall support 32 incoming channels and 16 outgoing channels over a local area network using standard Internet protocols
- Six incoming channels may be rerouted to input channel processing
- Shall support primary and redundant Dante audio networks
- Shall support Dante Controller software for digital audio network configuration
- Shall provide an internal four-port Gigabit switch on RJ-45 connectors to support Dante audio network connection and direct interconnection between Dante-enabled products
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Shall provide selectable 0.25 ms, 0.50 ms, 1.0 ms (default), 2.0 ms, or 5.0 ms of deterministic latency
- Shall support 32 incoming channels and 16 outgoing channels over a local area network using standard Internet protocols
- Control Requirements
- Shall accept an RJ-45 connector to provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN
- Shall accept 3.5 mm captive screw connectors to support bidirectional RS-232
- Shall provide an ACP audio control port to support the use of Extron Audio Control Panels.
- Shall provide a female USB mini type B port for software control
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232, Ethernet, or USB
- Shall provide 6 sets of 2 configurable digital I/O ports that accept 3.5 mm captive screw connectors and can be programmed to sense and then respond to external triggers
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port that accepts a USB mini type B connector
- Shall provide green LEDs for Expansion port, LAN ports, and USB audio interface activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for input and output clip warning indication
- Rear Panel Requirements
- Shall provide 6 inputs that accept 3.5 mm captive screw connectors
- Shall provide 4 outputs that accept 3.5 mm captive screw connectors
- Shall provide a digital audio interface on a mini USB B port
- Shall provide 6 digital input and 6 digital output ports that accept 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port that accepts a 3.5 mm captive screw connector
- Shall provide Expansion port that accepts an RJ-45 connector
- Shall provide Ethernet host port that accepts an RJ-45 connector
- Shall provide an ACP audio control port that accepts a 3.5 mm captive screw connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, half rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 64 Plus C V AT, part number 60-1824-10; no alternates or equals.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, 32x16 Dante™ audio networking, VoIP support, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
DMP 64 Plus C V AT
- Provide an audio digital matrix processor that shall support 6 mono analog inputs capable of microphone or line level signals and 4 mono analog line level outputs for signal routing and management.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, 32x16 Dante™ audio networking, VoIP support, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
- Input Requirements
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Microphone level
- Line level, balanced or unbalanced
- Shall provide input gain adjustment from -18 dB to +80 dB in 0.1 dB steps, adjustable per input
- Shall provide selectable +48 volt phantom power for condenser microphones on the six analog inputs
- Shall provide option to select an alternate input from the Dante audio network or EXP input on mic/line inputs 1 to 6
- Shall provide analog to digital conversion at 48 kHz sampling rate with 24-bit resolution
- Shall support six mono analog inputs that accept 3.5 mm captive screw connectors:
- Output Requirements
- Shall support four mono line level, balanced or unbalanced outputs that accept 3.5 mm captive screw connectors
- Shall provide output attenuation adjustment from 0 dB to -100 dB in 0.1 dB steps, adjustable per output
- Shall provide digital to analog conversion at 48 kHz sampling rate with 24-bit resolution
- DSP Engine Requirements
- Shall provide 64-bit floating point DSP engine
- Shall provide a mix matrix such that all inputs and returns can be discretely routed to any or all of the outputs or sends
- Shall provide 6 DSP channels with acoustic echo cancellation
- Shall provide a maximum, deterministic latency of 3.2 ms from input to output
- Shall provide additional, deterministic latency of 1.3 ms when Virtual Path routing is used
- Shall provide additional, deterministic latency of 12 ms when AEC is used
- Audio Device Requirements — Input to Output
- Shall provide an analog in to analog out signal-to-noise ratio of greater than 107 dB measured from 20 Hz to 20 kHz, at maximum balanced output, unweighted
- Shall provide a THD+N measurement of less than 0.02% measured at 20 Hz to 20 kHz, at maximum level
- Configuration Software Requirements
- Shall provide PC-based DSP Configurator software allowing flexible control of the digital signal processor’s fixed architecture
- Shall provide a Live mode for real-time control of parameters without compiling and file uploading to processor
- Shall provide an Emulate mode for offline configuration
- Shall provide single, scrollable window for viewing of all inputs and outputs, audio processing blocks, routing, mix points, and virtual routing
- Shall provide setup and configuration of digital audio processing tools including, but not limited to: Filters (high pass, low pass, bass shelving, treble shelving, parametric, dynamic loudness, and notch EQ); Dynamics processing (AGC, Compressor, Limiter, Noise Gate); Delay processing; Ducking and Adaptive Gain processing; Feedback Suppressor processing, Automixing; and multiple gain stages
- Shall provide cut, copy, paste editing between processing blocks
- Shall provide matrix routing with integrated mix point gain adjustment between inputs, outputs, aux inputs, aux outputs, virtual sends, virtual returns, expansion inputs, and expansion outputs
- Shall provide a library of pre-designed processor settings for inputs and outputs with user-customizable parameters
- Shall provide Group Master controls for consolidation of individual gain or mute control members of the same type into one point of control
- Shall provide Soft Limits settings to define upper and lower control limits on Group Masters for use with external controls
- Shall provide Presets for recall of any processing block setting, level setting or audio routing; presets shall be saved for the entire system, or any selected partial group of inputs, outputs, mix points, and DSP blocks
- Shall provide real-time metering of levels within each Input Gain, AGC, Compressor, Limiter, Noise Gate, Automixer, and Output Attenuation processing block in Live mode
- Shall provide a Meter Bridge window for real-time metering of all input and output channels with clipping indication in Live mode
- Shall provide keyboard-based navigation of configuration software utilizing directional controls, keyboard shortcuts, and spreadsheet software-style commands
- Shall provide file saving in both Live and Emulate mode
- Shall provide configuration file upload in Live mode
- Shall provide configuration and file saving of multiple, linked or networked processors from a single configuration software session
- Aux Input/Output Requirements
- Shall provide a total of 8 Aux Inputs to be configured with a combination of file players, VoIP appearances, and USB audio connections.
- Shall provide a total of 8 Aux Outputs, assignable to USB audio connections.
- Expansion Port Requirements
- Shall provide digital audio expansion port for bidirectional signal routing between two connected processors at sub-millisecond latency
- Shall support 16 incoming signals and 16 outgoing signals
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Product shall include as standard, 1 foot (0.3 m) shielded CAT 6 cable for the purposes of interconnecting two units
- Automixer Requirements
- Shall provide Automixer Group selection for optional channel assignment into any of eight groups
- Shall provide gated and gain sharing automixer types
- Shall provide Last Open Mic Priority and Chairman Priority modes
- Shall provide Max Number of Open Microphone parameter from 1 to 12 microphones
- Shall provide Gate Threshold level and adjustable Off Reduction level for gated channels
- Shall provide adjustable parameters for Attack, Hold, and Release times
- Shall provide real-time metering of Signal Level, Gate Status, and Gate Threshold target from within the Automix parameter setup window
- Shall provide global view with Gate Status indication of all channels assigned to an automixer group
- AEC – Acoustic Echo Cancellation Processing Requirements
- Shall provide six independent channels of AEC
- Shall provide real-time software-based metering of Echo Return Loss, Echo Return Loss Enhancement, and Total Echo Reduction levels
- Shall provide real-time indication of remote site activity, local site activity, and AEC processor reconverging
- Shall provide up to 20 dB of selectable noise cancellation for each AEC channel
- Shall provide advanced controls and adjustable parameters for Non-Linear Processing, Double Talk Echo Reduction, and Comfort Noise for each AEC channel
- Shall provide greater than 200 milliseconds of AEC tail length
- Shall provide up to 60 dB per second AEC convergence rate
- VoIP Requirements
- Shall provide up to eight VoIP lines based on RFC 3261 of the Session Initiation Protocol (SIP 2.0)
- Shall allow customizable assignment of auxiliary channels in order to support multiple call appearances for local conferencing applications
- Shall provide independent audio processing and control per call appearance
- Shall support the following audio codecs, with selectable priority:
- G.711u (PCM u)
- G.711a (PCM a)
- G.722
- G.722.1 24/32
- G.722.1c 24/32/48
- G.726 16/24/32/40
- G.726 AAL-2 16/24/32/40
- G.729A
- Shall support VoIP configuration via an onboard webpage that includes SIP transaction logging, packet count, and network jitter
- Shall provide selection of LAN 1 or LAN 2 as the VoIP Network Interface
- Shall provide the ability to be controlled via LAN 1 or LAN 2
- Shall support VLAN tagging on either LAN 1 or LAN 2, using the 802.11Q protocol
- Shall support Quality of Service – QoS for Layer 2 and Layer 3
- Shall support Transport Layer Security – TLS and Secure Real-Time Transport Protocol – SRTP
- Shall support NAT Traversal via STUN, TURN, and ICE
- Shall support Link Layer Discovery Protocol – Media Endpoint Discovery – LLDP-MED
- Dante Audio Networking Requirements
- Shall support 32 incoming channels and 16 outgoing channels over a local area network using standard Internet protocols
- Six incoming channels may be rerouted to input channel processing
- Shall support primary and redundant Dante audio networks
- Shall support Dante Controller software for digital audio network configuration
- Shall provide an internal four-port Gigabit switch on RJ-45 connectors to support Dante audio network connection and direct interconnection between Dante-enabled products
- Shall provide uncompressed digital audio at 48 kHz sampling rate with 24-bit resolution
- Shall provide selectable 0.25 ms, 0.50 ms, 1.0 ms (default), 2.0 ms, or 5.0 ms of deterministic latency
- Shall support 32 incoming channels and 16 outgoing channels over a local area network using standard Internet protocols
- Control Requirements
- Shall accept an RJ-45 connector to provide Ethernet monitoring and control using standard TCP/IP protocols to support real-time monitoring and system management over a LAN or WAN
- Shall accept 3.5 mm captive screw connectors to support bidirectional RS-232
- Shall provide an ACP audio control port to support the use of Extron Audio Control Panels.
- Shall provide a female USB mini type B port for software control
- Shall support remote control operation via external control system using Simple Instruction Set commands sent over RS-232, Ethernet, or USB
- Shall provide 6 sets of 2 configurable digital I/O ports that accept 3.5 mm captive screw connectors and can be programmed to sense and then respond to external triggers
- Front Panel Requirements
- Shall provide a green LED for power indication
- Shall provide Configuration port that accepts a USB mini type B connector
- Shall provide green LEDs for Expansion port, LAN ports, and USB audio interface activity indication
- Shall provide green LEDs for input and output signal presence indication
- Shall provide red LEDs for input and output clip warning indication
- Rear Panel Requirements
- Shall provide 6 inputs that accept 3.5 mm captive screw connectors
- Shall provide 4 outputs that accept 3.5 mm captive screw connectors
- Shall provide a digital audio interface on a mini USB B port
- Shall provide 6 digital input and 6 digital output ports that accept 3.5 mm captive screw connectors
- Shall provide bidirectional RS-232 port that accepts a 3.5 mm captive screw connector
- Shall provide Expansion port that accepts an RJ-45 connector
- Shall provide Ethernet host port that accepts an RJ-45 connector
- Shall provide an ACP audio control port that accepts a 3.5 mm captive screw connector
- General Requirements
- Shall provide internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall be enclosed in a rack-mountable 1U, half rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron DMP 64 Plus C V AT, part number 60-1824-10; no alternates or equals.
- 6 input, 4 output audio digital matrix processor with acoustic echo cancellation, 32x16 Dante™ audio networking, VoIP support, digital audio expansion port, automixer function with eight groups, 64-bit floating point DSP engine, USB audio interface, macros, 8x8 configurable aux inputs / outputs, 16 virtual processing loops, up to eight audio file players, ACP audio control panel support, and 24-bit/48 kHz audio converters
アイテムをカートに追加する
Order Message Number
製品番号
注: Extron products using the Universal AC Outlet accept a number of different AC plug types. Before use, ensure that the device meets all regulatory requirements for your region and complies with all applicable local safety and electrical codes and standards.
現在の合計金額:
Annotation Graphics Processor
To view this page ensure that Adobe Flash Player version
11.0.0 or greater is installed and enabled.
Chrome
Firefox
Edge
Safari