最近閲覧した製品
SM 3
コンサルタント向け資料
製品番号を選択してください:
テキストをコピー
コピーされました!
エラーが発生しました。しばらくしてからもう一度お試しください。
SM 3
- Provide a compact, full-range 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
- Compact, full-range surface mount speaker with a single-ported enclosure, grille, 8 ohm nominal impedance, and a concealed mounting system
- Driver Requirements
- Shall consist of a 3" full-range driver with a tuned bass reflex port
- Performance Requirements
- Shall provide a frequency range of 75 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 15 watts (rms) continuous pink noise per IEC 60268-5 and 30 watts (rms) continuous program
- Shall provide a nominal sensitivity of 83 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Electrical Requirements
- Shall support 8 ohm direct connection from power amplifiers
- Shall support incoming speaker level signal on one 2-pole, 10 mm Euro-style captive screw terminal block built into 0° and 10° mounting plate
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grill and bass reflex port
- Shall have a black or white finish
- Shall measure 8.75" (22.2 cm) in height when using 0° mounting plate
- Shall measure 8.9" (22.6 cm) in height when using 10° mounting plate
- Shall measure 5.75" (14.6 cm) in width when using 0° or 10° mounting plate
- Shall protrude 4.0" (10.2 cm) into environment from mounting surface when using 0° mounting plate
- Shall comply with ADA – Americans with Disabilities Act standards for protruding object limits when using 0° mounting plate
- Shall protrude 5.0" (12.7 cm) into environment from mounting surface when using 10° mounting plate
- Shall weigh 2.1 lbs (1.0 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical, horizontal, or flush with the wall installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall have a black or white finish to match speaker
- Shall include a 10° mounting plate for vertical or horizontal speaker installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access with 0° and 10° mounting plate for surface-mounted wiring
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical, horizontal, or flush with the wall installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 3, part number 42-133-02 or 42-133-03; no alternates or equals.
- Compact, full-range surface mount speaker with a single-ported enclosure, grille, 8 ohm nominal impedance, and a concealed mounting system
SM 3
- Provide a compact, full-range 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
- Compact, full-range surface mount speaker with a single-ported enclosure, grille, 8 ohm nominal impedance, and a concealed mounting system
- Driver Requirements
- Shall consist of a 3" full-range driver with a tuned bass reflex port
- Performance Requirements
- Shall provide a frequency range of 75 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 15 watts (rms) continuous pink noise per IEC 60268-5 and 30 watts (rms) continuous program
- Shall provide a nominal sensitivity of 83 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Electrical Requirements
- Shall support 8 ohm direct connection from power amplifiers
- Shall support incoming speaker level signal on one 2-pole, 10 mm Euro-style captive screw terminal block built into 0° and 10° mounting plate
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grill and bass reflex port
- Shall have a black or white finish
- Shall measure 8.75" (22.2 cm) in height when using 0° mounting plate
- Shall measure 8.9" (22.6 cm) in height when using 10° mounting plate
- Shall measure 5.75" (14.6 cm) in width when using 0° or 10° mounting plate
- Shall protrude 4.0" (10.2 cm) into environment from mounting surface when using 0° mounting plate
- Shall comply with ADA – Americans with Disabilities Act standards for protruding object limits when using 0° mounting plate
- Shall protrude 5.0" (12.7 cm) into environment from mounting surface when using 10° mounting plate
- Shall weigh 2.1 lbs (1.0 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical, horizontal, or flush with the wall installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall have a black or white finish to match speaker
- Shall include a 10° mounting plate for vertical or horizontal speaker installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access with 0° and 10° mounting plate for surface-mounted wiring
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical, horizontal, or flush with the wall installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 3, part number 42-133-02 or 42-133-03; no alternates or equals.
- Compact, full-range surface mount speaker with a single-ported enclosure, grille, 8 ohm nominal impedance, and a concealed mounting system
SM 3
- Provide a compact, full-range 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
- Compact, full-range surface mount speaker with a single-ported enclosure, grille, 8 ohm nominal impedance, and a concealed mounting system
- Driver Requirements
- Shall consist of a 3" full-range driver with a tuned bass reflex port
- Performance Requirements
- Shall provide a frequency range of 75 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 15 watts (rms) continuous pink noise per IEC 60268-5 and 30 watts (rms) continuous program
- Shall provide a nominal sensitivity of 83 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Electrical Requirements
- Shall support 8 ohm direct connection from power amplifiers
- Shall support incoming speaker level signal on one 2-pole, 10 mm Euro-style captive screw terminal block built into 0° and 10° mounting plate
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grill and bass reflex port
- Shall have a black or white finish
- Shall measure 8.75" (22.2 cm) in height when using 0° mounting plate
- Shall measure 8.9" (22.6 cm) in height when using 10° mounting plate
- Shall measure 5.75" (14.6 cm) in width when using 0° or 10° mounting plate
- Shall protrude 4.0" (10.2 cm) into environment from mounting surface when using 0° mounting plate
- Shall comply with ADA – Americans with Disabilities Act standards for protruding object limits when using 0° mounting plate
- Shall protrude 5.0" (12.7 cm) into environment from mounting surface when using 10° mounting plate
- Shall weigh 2.1 lbs (1.0 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical, horizontal, or flush with the wall installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall have a black or white finish to match speaker
- Shall include a 10° mounting plate for vertical or horizontal speaker installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access with 0° and 10° mounting plate for surface-mounted wiring
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical, horizontal, or flush with the wall installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 3, part number 42-133-02 or 42-133-03; no alternates or equals.
- Compact, full-range surface mount speaker with a single-ported enclosure, grille, 8 ohm nominal impedance, and a concealed mounting system
SM 3
- Provide a compact, full-range 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
- Compact, full-range surface mount speaker with a single-ported enclosure, grille, 8 ohm nominal impedance, and a concealed mounting system
- Driver Requirements
- Shall consist of a 3" full-range driver with a tuned bass reflex port
- Performance Requirements
- Shall provide a frequency range of 75 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 15 watts (rms) continuous pink noise per IEC 60268-5 and 30 watts (rms) continuous program
- Shall provide a nominal sensitivity of 83 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Electrical Requirements
- Shall support 8 ohm direct connection from power amplifiers
- Shall support incoming speaker level signal on one 2-pole, 10 mm Euro-style captive screw terminal block built into 0° and 10° mounting plate
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grill and bass reflex port
- Shall have a black or white finish
- Shall measure 8.75" (22.2 cm) in height when using 0° mounting plate
- Shall measure 8.9" (22.6 cm) in height when using 10° mounting plate
- Shall measure 5.75" (14.6 cm) in width when using 0° or 10° mounting plate
- Shall protrude 4.0" (10.2 cm) into environment from mounting surface when using 0° mounting plate
- Shall comply with ADA – Americans with Disabilities Act standards for protruding object limits when using 0° mounting plate
- Shall protrude 5.0" (12.7 cm) into environment from mounting surface when using 10° mounting plate
- Shall weigh 2.1 lbs (1.0 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical, horizontal, or flush with the wall installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall have a black or white finish to match speaker
- Shall include a 10° mounting plate for vertical or horizontal speaker installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access with 0° and 10° mounting plate for surface-mounted wiring
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical, horizontal, or flush with the wall installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 3, part number 42-133-02 or 42-133-03; no alternates or equals.
- Compact, full-range surface mount speaker with a single-ported enclosure, grille, 8 ohm nominal impedance, and a concealed mounting system
アイテムをカートに追加する
Order Message Number
製品番号
注: Extron products using the Universal AC Outlet accept a number of different AC plug types. Before use, ensure that the device meets all regulatory requirements for your region and complies with all applicable local safety and electrical codes and standards.
現在の合計金額:

Chrome
Firefox
Edge
Safari