最近閲覧した製品
IN1808シリーズ
コンサルタント向け資料
製品番号を選択してください:
テキストをコピー
コピーされました！
エラーが発生しました。しばらくしてからもう一度お試しください。
IN1808
- Provide a video scaling presentation switcher that shall support up to eight inputs and two simultaneous outputs for processing and switching of DisplayPort and HDMI video sources, with additional support for signal extension over shielded CATx cable
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
- Video Input Requirements
- Provide video input connections
- One (1) DisplayPort supporting DisplayPort SST - Single Stream Transport data rates up to 21.6 Gbps
- Five (5) HDMI supporting HDMI specifications including 4K/60 Deep Color, data rates up to 18 Gbps, and HD lossless audio formats
- Two (2) RJ-45 for DTP2 twisted pair
- Provide automatic detection of input video parameters
- Determine total pixels, active pixels, active lines, H/V starting points, H/V image positions, H/V image sizes, and video clock phase
- The user may selectively enable to disable automatic detection for each input
- Provide image adjustments for brightness, contrast, color, tint, detail, H/V positioning, and sizing
- Provide storage and recall of video parameters and picture settings
- Automatic memories for each video input
- Save video settings and picture adjustments without user intervention
- Automatically recall settings when the same video rate is encountered
- The user may selectively enable or disable automatic memories
- Manual user presets
- Save picture adjustments
- User presets may be saved and recalled using front panel controls
- User presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Manual input presets
- Save video settings and picture adjustments
- Input presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Automatic memories for each video input
- Provide automatic 3:2 and 2:2 pulldown detection
- Provide video input connections
- Video Output Requirements
- Provide one (1) HDMI for loop-through without video scaling, selectable for any video input.
- Provide scaled video output connections
- One (1) HDMI
- One (1) RJ-45 for DTP2 twisted pair
- Provide a range of selectable video output rates from 640x480 to 4096x2160 @ 60 Hz
- Support custom user-defined output resolutions via EDID management
- Provide image scaling and video format conversion with 30-bit precision and 4:4:4 chroma sampling
- Provide motion adaptive deinterlacing for signals up to 1080i
- Provide aspect ratio control
- When in FILL mode, the video image shall always fill the output screen without letterbox or pillarbox
- When in FOLLOW mode, the video image on the output screen shall always preserve the aspect ratio of the input signals without distortion
- Provide internal test patterns for calibration and setup
- Support image freeze via Ethernet, RS-232 or USB connection
- Support upload and placement of a custom logo graphic at any position on the video output
- Support logo placement as a foreground image
- Shall support uploading logo graphics in BMP, JPG, PNG, GIF, or TIFF format
- Shall support displaying full screen images up to 4096x2160 resolution
- Shall support up to 16 logo presets
- Shall support keying with selectable effects including transparency, color key, level key, and alpha key
- Support automatic muting of video and sync output when no video input signal is present
- Provide a choice to generate a blue screen or a black screen before disabling sync
- Provide a configurable timeout period before disabling sync
- The user may selectively enable or disable automatic muting of sync output
- Provide a low power standby state selectable via Ethernet, RS-232 or USB
- Support the connection of DVI displays that do not recognize HDMI-specific formats
- Automatically enable or disable embedded TMDS audio and InfoFrames
- Automatically set the correct color space
- Support selection of output color space as RGB or component video
- Switching Requirements
- Provide configurable automatic switching modes between input sources
- Last connected: always switch to the last active connected input
- Configurable priority: switching priority may be assigned arbitrarily for any combination of the four inputs
- Provide selectable transition effects when switching inputs
- Seamless Cut: video output shall freeze, then cut to the newly selected input source
- Seamless Fade: video output shall freeze, then fade into the newly selected input source
- Cut through black: video output shall cut to black, then cut to the newly selected input source
- Fade through black: video output shall fade to black, then fade into the newly selected input source
- Accompanying audio shall ramp down, then ramp up to match the transition effect
- Provide configurable automatic switching modes between input sources
- EDID Requirements
- Provide automatic EDID management between connected devices
- Provide a set of pre-stored EDID files
- Support capture of EDID from any connected display
- Support user uploading of custom-generated EDID files
- Support assignment of any pre-stored, captured, or custom uploaded EDID file to any input connection
- Provide automatic EDID management between connected devices
- HDCP Requirements
- The unit shall be HDCP 2.3 compliant
- Provide authentication and maintain continuous verification of HDCP key exchange with connected sink devices
- Provide authentication and maintain continuous verification of HDCP key exchange with connected source devices
- Provide the option to disable HDCP processing at video inputs when passing unencrypted content
- Provide selectable, human-readable visual confirmation of HDCP compliance when encrypted content is routed to a non-HDCP compliant display
- When enabled, the video output shall be a solid green color and an on-screen message stating “HDCP CONTENT” shall be displayed
- When enabled, the option shall be provided to display a user-provided image in place of the green video output
- When disabled, the output shall be muted
- Provide real-time verification of HDCP status for each video input and output
- Directly readable on front panel LEDs
- Electronically accessible over Ethernet, RS-232 or USB connection
- The unit shall be HDCP 2.3 compliant
- DTP2 Twisted pair requirements
- Provide signal transmission distance capability of 330 feet (100 meters) for all supported video resolutions using a shielded CATx cable
- Support video, audio, RS-232, IR, and power transmission over a single shielded CATx cable
- Shall be compatible with CATx shielded twisted pair cable, and Extron XTP DTP 24 shielded twisted pair cable
- Support computer and video resolutions up to 3840x2160/60 at 4:4:4 chroma sampling
- Support stereo audio pass-through signals
- Shall actively buffer DDC channels
- Shall be configurable for compatibility with
- Extron DTP inputs
- Extron DTP2 inputs
- Extron XTP matrix switcher inputs
- HDBaseT inputs
- Provide power to remote DTP or DTP2 endpoint connected over the shielded CATx cable.
- Audio Requirements
- Provide audio input connections
- One (1) DisplayPort, embedded
- Five (5) HDMI, embedded
- Two (2) 5-pole 3.5 mm captive screw, balanced/unbalanced line level analog stereo
- Two (2) 3-pole 3.5 mm captive screw, balanced/unbalanced mic/line level with +48 volt phantom power
- Provide audio output connections
- Two (2) 5-pole 3.5 mm captive screw, with output level control and configurable for balanced/unbalanced, analog stereo or dual mono
- One (1) HDMI, embedded and with output level control for two-channel PCM
- One (1) RJ-45 for DTP2 twisted pair transmitting both:
- Embedded digital audio
- Pass-through stereo audio
- Support embedding of the analog audio input signal on the HDMI and DTP2 outputs
- Support extraction of two-channel PCM embedded audio signals to analog audio outputs, or pass bitstream audio to the HDMI and DTP2 outputs
- Provide the capability for all video inputs to share a common analog audio input
- Provide a delay in the audio output to match the corresponding video processing delay
- Provide gain and attenuation adjustments for analog input audio
- Support individual muting of the analog stereo or embedded digital audio outputs
- DSP Requirements
- Provide digital audio processing tools including gain, mixing, parametric EQ, filtering, dynamics, and ducking
- Provide adjustable, automatic ducking of program audio when a signal is detected on microphone inputs
- Provide DSP configuration and parameter adjustments through the product configuration software
- Provide real-time level meters for inputs and outputs in the product configuration software
- Provide live DSP parameter adjustments while they are heard or metered in real-time
- Provide user presets for saving and recalling DSP parameters
- Support storage and playback of up to 16 audio files at any audio output.
- Provide audio input connections
- Control/remote - RS-232 and IR Pass-Through Over Shielded CATx Requirements
- Provide connections for AV device control
- One (1) 3-pole 3.5 mm captive screw: IR pass-through to a DTP twisted pair receiver
- Support Ethernet insertion of RS-232 signals for transmission to a DTP endpoint
- Support RS-232 and IR transmission over shielded CATx up to 330 feet (100 meters)
- Provide connections for AV device control
- Control/remote – Presentation Switcher Requirements
- Provide control connections
- One (1) RJ-45: 10/100/1000Base-T Ethernet
- One (1) 3-pole 3.5 mm captive screw: RS-232
- One (1) Mini USB-B: USB 2.0
- Provide alternatives for configuration and operation
- On-screen menus navigated using front panel controls
- Product configuration software connected via Ethernet, USB, or RS-232
- Serial commands sent over Ethernet, RS-232 or USB connection
- Support disabling of front panel controls to prevent inadvertent or unauthorized changes to configuration settings
- Support triggering of standard CEC commands at main HDMI and DTP2 outputs
- Provide control connections
- General Requirements
- Enclosure shall be rack-mountable, full rack width, and 1RU in height
- Shall be equipped with an internal 100-240 VAC, 50/60 Hz universal power supply
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Video Input Requirements
- Approved device shall be the Extron IN1808 (part number 60-1615-01); no alternates or equals
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
IN1808
- Provide a video scaling presentation switcher that shall support up to eight inputs and two simultaneous outputs for processing and switching of DisplayPort and HDMI video sources, with additional support for signal extension over shielded CATx cable
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
- Video Input Requirements
- Provide video input connections
- One (1) DisplayPort supporting DisplayPort SST - Single Stream Transport data rates up to 21.6 Gbps
- Five (5) HDMI supporting HDMI specifications including 4K/60 Deep Color, data rates up to 18 Gbps, and HD lossless audio formats
- Two (2) RJ-45 for DTP2 twisted pair
- Provide automatic detection of input video parameters
- Determine total pixels, active pixels, active lines, H/V starting points, H/V image positions, H/V image sizes, and video clock phase
- The user may selectively enable to disable automatic detection for each input
- Provide image adjustments for brightness, contrast, color, tint, detail, H/V positioning, and sizing
- Provide storage and recall of video parameters and picture settings
- Automatic memories for each video input
- Save video settings and picture adjustments without user intervention
- Automatically recall settings when the same video rate is encountered
- The user may selectively enable or disable automatic memories
- Manual user presets
- Save picture adjustments
- User presets may be saved and recalled using front panel controls
- User presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Manual input presets
- Save video settings and picture adjustments
- Input presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Automatic memories for each video input
- Provide automatic 3:2 and 2:2 pulldown detection
- Provide video input connections
- Video Output Requirements
- Provide one (1) HDMI for loop-through without video scaling, selectable for any video input.
- Provide scaled video output connections
- One (1) HDMI
- One (1) RJ-45 for DTP2 twisted pair
- Provide a range of selectable video output rates from 640x480 to 4096x2160 @ 60 Hz
- Support custom user-defined output resolutions via EDID management
- Provide image scaling and video format conversion with 30-bit precision and 4:4:4 chroma sampling
- Provide motion adaptive deinterlacing for signals up to 1080i
- Provide aspect ratio control
- When in FILL mode, the video image shall always fill the output screen without letterbox or pillarbox
- When in FOLLOW mode, the video image on the output screen shall always preserve the aspect ratio of the input signals without distortion
- Provide internal test patterns for calibration and setup
- Support image freeze via Ethernet, RS-232 or USB connection
- Support upload and placement of a custom logo graphic at any position on the video output
- Support logo placement as a foreground image
- Shall support uploading logo graphics in BMP, JPG, PNG, GIF, or TIFF format
- Shall support displaying full screen images up to 4096x2160 resolution
- Shall support up to 16 logo presets
- Shall support keying with selectable effects including transparency, color key, level key, and alpha key
- Support automatic muting of video and sync output when no video input signal is present
- Provide a choice to generate a blue screen or a black screen before disabling sync
- Provide a configurable timeout period before disabling sync
- The user may selectively enable or disable automatic muting of sync output
- Provide a low power standby state selectable via Ethernet, RS-232 or USB
- Support the connection of DVI displays that do not recognize HDMI-specific formats
- Automatically enable or disable embedded TMDS audio and InfoFrames
- Automatically set the correct color space
- Support selection of output color space as RGB or component video
- Switching Requirements
- Provide configurable automatic switching modes between input sources
- Last connected: always switch to the last active connected input
- Configurable priority: switching priority may be assigned arbitrarily for any combination of the four inputs
- Provide selectable transition effects when switching inputs
- Seamless Cut: video output shall freeze, then cut to the newly selected input source
- Seamless Fade: video output shall freeze, then fade into the newly selected input source
- Cut through black: video output shall cut to black, then cut to the newly selected input source
- Fade through black: video output shall fade to black, then fade into the newly selected input source
- Accompanying audio shall ramp down, then ramp up to match the transition effect
- Provide configurable automatic switching modes between input sources
- EDID Requirements
- Provide automatic EDID management between connected devices
- Provide a set of pre-stored EDID files
- Support capture of EDID from any connected display
- Support user uploading of custom-generated EDID files
- Support assignment of any pre-stored, captured, or custom uploaded EDID file to any input connection
- Provide automatic EDID management between connected devices
- HDCP Requirements
- The unit shall be HDCP 2.3 compliant
- Provide authentication and maintain continuous verification of HDCP key exchange with connected sink devices
- Provide authentication and maintain continuous verification of HDCP key exchange with connected source devices
- Provide the option to disable HDCP processing at video inputs when passing unencrypted content
- Provide selectable, human-readable visual confirmation of HDCP compliance when encrypted content is routed to a non-HDCP compliant display
- When enabled, the video output shall be a solid green color and an on-screen message stating “HDCP CONTENT” shall be displayed
- When enabled, the option shall be provided to display a user-provided image in place of the green video output
- When disabled, the output shall be muted
- Provide real-time verification of HDCP status for each video input and output
- Directly readable on front panel LEDs
- Electronically accessible over Ethernet, RS-232 or USB connection
- The unit shall be HDCP 2.3 compliant
- DTP2 Twisted pair requirements
- Provide signal transmission distance capability of 330 feet (100 meters) for all supported video resolutions using a shielded CATx cable
- Support video, audio, RS-232, IR, and power transmission over a single shielded CATx cable
- Shall be compatible with CATx shielded twisted pair cable, and Extron XTP DTP 24 shielded twisted pair cable
- Support computer and video resolutions up to 3840x2160/60 at 4:4:4 chroma sampling
- Support stereo audio pass-through signals
- Shall actively buffer DDC channels
- Shall be configurable for compatibility with
- Extron DTP inputs
- Extron DTP2 inputs
- Extron XTP matrix switcher inputs
- HDBaseT inputs
- Provide power to remote DTP or DTP2 endpoint connected over the shielded CATx cable.
- Audio Requirements
- Provide audio input connections
- One (1) DisplayPort, embedded
- Five (5) HDMI, embedded
- Two (2) 5-pole 3.5 mm captive screw, balanced/unbalanced line level analog stereo
- Two (2) 3-pole 3.5 mm captive screw, balanced/unbalanced mic/line level with +48 volt phantom power
- Provide audio output connections
- Two (2) 5-pole 3.5 mm captive screw, with output level control and configurable for balanced/unbalanced, analog stereo or dual mono
- One (1) HDMI, embedded and with output level control for two-channel PCM
- One (1) RJ-45 for DTP2 twisted pair transmitting both:
- Embedded digital audio
- Pass-through stereo audio
- Support embedding of the analog audio input signal on the HDMI and DTP2 outputs
- Support extraction of two-channel PCM embedded audio signals to analog audio outputs, or pass bitstream audio to the HDMI and DTP2 outputs
- Provide the capability for all video inputs to share a common analog audio input
- Provide a delay in the audio output to match the corresponding video processing delay
- Provide gain and attenuation adjustments for analog input audio
- Support individual muting of the analog stereo or embedded digital audio outputs
- DSP Requirements
- Provide digital audio processing tools including gain, mixing, parametric EQ, filtering, dynamics, and ducking
- Provide adjustable, automatic ducking of program audio when a signal is detected on microphone inputs
- Provide DSP configuration and parameter adjustments through the product configuration software
- Provide real-time level meters for inputs and outputs in the product configuration software
- Provide live DSP parameter adjustments while they are heard or metered in real-time
- Provide user presets for saving and recalling DSP parameters
- Support storage and playback of up to 16 audio files at any audio output.
- Provide audio input connections
- Control/remote - RS-232 and IR Pass-Through Over Shielded CATx Requirements
- Provide connections for AV device control
- One (1) 3-pole 3.5 mm captive screw: IR pass-through to a DTP twisted pair receiver
- Support Ethernet insertion of RS-232 signals for transmission to a DTP endpoint
- Support RS-232 and IR transmission over shielded CATx up to 330 feet (100 meters)
- Provide connections for AV device control
- Control/remote – Presentation Switcher Requirements
- Provide control connections
- One (1) RJ-45: 10/100/1000Base-T Ethernet
- One (1) 3-pole 3.5 mm captive screw: RS-232
- One (1) Mini USB-B: USB 2.0
- Provide alternatives for configuration and operation
- On-screen menus navigated using front panel controls
- Product configuration software connected via Ethernet, USB, or RS-232
- Serial commands sent over Ethernet, RS-232 or USB connection
- Support disabling of front panel controls to prevent inadvertent or unauthorized changes to configuration settings
- Support triggering of standard CEC commands at main HDMI and DTP2 outputs
- Provide control connections
- General Requirements
- Enclosure shall be rack-mountable, full rack width, and 1RU in height
- Shall be equipped with an internal 100-240 VAC, 50/60 Hz universal power supply
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Video Input Requirements
- Approved device shall be the Extron IN1808 (part number 60-1615-01); no alternates or equals
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
IN1808 IPCP Q SA
- Provide a video scaling presentation switcher that shall support up to eight inputs and two simultaneous outputs for processing and switching of DisplayPort and HDMI video sources, with additional support for signal extension over shielded CATx cable
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
- Video Input Requirements
- Provide video input connections
- One (1) DisplayPort supporting DisplayPort SST - Single Stream Transport data rates up to 21.6 Gbps
- Five (5) HDMI supporting HDMI specifications including 4K/60 Deep Color, data rates up to 18 Gbps, and HD lossless audio formats
- Two (2) RJ-45 for DTP2 twisted pair
- Provide automatic detection of input video parameters
- Determine total pixels, active pixels, active lines, H/V starting points, H/V image positions, H/V image sizes, and video clock phase
- The user may selectively enable to disable automatic detection for each input
- Provide image adjustments for brightness, contrast, color, tint, detail, H/V positioning, and sizing
- Provide storage and recall of video parameters and picture settings
- Automatic memories for each video input
- Save video settings and picture adjustments without user intervention
- Automatically recall settings when the same video rate is encountered
- The user may selectively enable or disable automatic memories
- Manual user presets
- Save picture adjustments
- User presets may be saved and recalled using front panel controls
- User presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Manual input presets
- Save video settings and picture adjustments
- Input presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Automatic memories for each video input
- Provide automatic 3:2 and 2:2 pulldown detection
- Provide video input connections
- Video Output Requirements
- Provide one (1) HDMI for loop-through without video scaling, selectable for any video input.
- Provide scaled video output connections
- One (1) HDMI
- One (1) RJ-45 for DTP2 twisted pair
- Provide a range of selectable video output rates from 640x480 to 4096x2160 @ 60 Hz
- Support custom user-defined output resolutions via EDID management
- Provide image scaling and video format conversion with 30-bit precision and 4:4:4 chroma sampling
- Provide motion adaptive deinterlacing for signals up to 1080i
- Provide aspect ratio control
- When in FILL mode, the video image shall always fill the output screen without letterbox or pillarbox
- When in FOLLOW mode, the video image on the output screen shall always preserve the aspect ratio of the input signals without distortion
- Provide internal test patterns for calibration and setup
- Support image freeze via Ethernet, RS-232 or USB connection
- Support upload and placement of a custom logo graphic at any position on the video output
- Support logo placement as a foreground image
- Shall support uploading logo graphics in BMP, JPG, PNG, GIF, or TIFF format
- Shall support displaying full screen images up to 4096x2160 resolution
- Shall support up to 16 logo presets
- Shall support keying with selectable effects including transparency, color key, level key, and alpha key
- Support automatic muting of video and sync output when no video input signal is present
- Provide a choice to generate a blue screen or a black screen before disabling sync
- Provide a configurable timeout period before disabling sync
- The user may selectively enable or disable automatic muting of sync output
- Provide a low power standby state selectable via Ethernet, RS-232 or USB
- Support the connection of DVI displays that do not recognize HDMI-specific formats
- Automatically enable or disable embedded TMDS audio and InfoFrames
- Automatically set the correct color space
- Support selection of output color space as RGB or component video
- Switching Requirements
- Provide configurable automatic switching modes between input sources
- Last connected: always switch to the last active connected input
- Configurable priority: switching priority may be assigned arbitrarily for any combination of the four inputs
- Provide selectable transition effects when switching inputs
- Seamless Cut: video output shall freeze, then cut to the newly selected input source
- Seamless Fade: video output shall freeze, then fade into the newly selected input source
- Cut through black: video output shall cut to black, then cut to the newly selected input source
- Fade through black: video output shall fade to black, then fade into the newly selected input source
- Accompanying audio shall ramp down, then ramp up to match the transition effect
- Provide configurable automatic switching modes between input sources
- EDID Requirements
- Provide automatic EDID management between connected devices
- Provide a set of pre-stored EDID files
- Support capture of EDID from any connected display
- Support user uploading of custom-generated EDID files
- Support assignment of any pre-stored, captured, or custom uploaded EDID file to any input connection
- Provide automatic EDID management between connected devices
- HDCP Requirements
- The unit shall be HDCP 2.2 compliant
- Provide authentication and maintain continuous verification of HDCP key exchange with connected sink devices
- Provide authentication and maintain continuous verification of HDCP key exchange with connected source devices
- Provide the option to disable HDCP processing at video inputs 2 through 8 when passing unencrypted content
- Provide selectable, human-readable visual confirmation of HDCP compliance when encrypted content is routed to a non-HDCP compliant display
- When enabled, the video output shall be a solid green color and an on-screen message stating “HDCP CONTENT” shall be displayed
- When enabled, the option shall be provided to display a user-provided image in place of the green video output
- When disabled, the output shall be muted
- Provide real-time verification of HDCP status for each video input and output
- Directly readable on front panel LEDs
- Electronically accessible over Ethernet, RS-232 or USB connection
- The unit shall be HDCP 2.2 compliant
- DTP2 Twisted pair requirements
- Provide signal transmission distance capability of 330 feet (100 meters) for all supported video resolutions using a shielded CATx cable
- Support video, audio, RS-232, IR, and power transmission over a single shielded CATx cable
- Shall be compatible with CATx shielded twisted pair cable, and Extron XTP DTP 24 shielded twisted pair cable
- Support computer and video resolutions up to 3840x2160/60 at 4:4:4 chroma sampling
- Support stereo audio pass-through signals
- Shall actively buffer DDC channels
- Shall be configurable for compatibility with
- Extron DTP inputs
- Extron DTP2 inputs
- Extron XTP matrix switcher inputs
- HDBaseT inputs
- Provide power to remote DTP or DTP2 endpoint connected over the shielded CATx cable.
- Audio Requirements
- Provide audio input connections
- One (1) DisplayPort, embedded
- Five (5) HDMI, embedded
- Two (2) 5-pole 3.5 mm captive screw, balanced/unbalanced line level analog stereo
- Two (2) 3-pole 3.5 mm captive screw, balanced/unbalanced mic/line level with +48 volt phantom power
- Provide audio output connections
- One (1) 4-pole, 5 mm captive screw, speaker level connector for stereo signal or dual mono
- Two (2) 5-pole 3.5 mm captive screw, with output level control and configurable for balanced/unbalanced, analog stereo or dual mono
- One (1) HDMI, embedded and with output level control for two-channel PCM
- One (1) RJ-45 for DTP2 twisted pair transmitting both:
- Embedded digital audio
- Pass-through stereo audio
- Provide stereo amplification for low impedance speaker systems
- Support one stereo speaker level signal or two mono speaker level signals on one 4-pole, 5 mm screw-lock captive screw connector
- Provide a total of 100 watts rms output power with 50 watts rms per channel into 4 ohms, or 25 watts rms per channel into 8 ohms measured at 1 kHz with 0.1% THD
- Provide a THD+N measurement of less than 0.1 % measured at 3 dB below clipping
- Provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Utilize an efficient Class D amplifier design
- Provide Class D Ripple Suppression technology
- Provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain with a slow attack and fast release to eliminate clipping distortion
- Provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults
- Support embedding of the analog audio input signal on the HDMI and DTP2 outputs
- Support extraction of two-channel PCM embedded audio signals to analog audio outputs, or pass bitstream audio to the HDMI and DTP2 outputs
- Provide the capability for all video inputs to share a common analog audio input
- Provide a delay in the audio output to match the corresponding video processing delay
- Provide gain and attenuation adjustments for analog input audio
- Support individual muting of the analog stereo or embedded digital audio outputs
- DSP Requirements
- Provide digital audio processing tools including gain, mixing, parametric EQ, filtering, dynamics, and ducking
- Provide adjustable, automatic ducking of program audio when a signal is detected on microphone inputs
- Provide DSP configuration and parameter adjustments through the product configuration software
- Provide real-time level meters for inputs and outputs in the product configuration software
- Provide live DSP parameter adjustments while they are heard or metered in real-time
- Provide user presets for saving and recalling DSP parameters
- Support storage and playback of up to 16 audio files at any audio output.
- Provide audio input connections
- Integrated Control Processor Requirements
- Provide AV system control connections
- Three RJ-45: 10/100/1000Base-T Ethernet, half/full duplex with auto-detect for connection to a LAN and include link and activity LED indicators located on the left and right of each jack for troubleshooting network issues, these ports will be designated as AV LAN ports allowing for AV devices to be isolated from a corporate network.
- AV LAN ports shall support a DHCP server that can distribute 50 dynamic IP addresses with a 24-hour lease
- One RJ-45: 10/100/1000Base-T, half/full duplex with auto-detect for connection to a LAN or WAN and includes link and activity LED indicators located on the left and right of the jack for troubleshooting network issues.
- Two 3-pole 3.5 mm captive screw: RS-232, configurable for unidirectional or bidirectional control of AV system components
- One 5-pole 3.5 mm captive screw: RS-232/RS-422/RS-485, configurable for unidirectional or bidirectional control of AV system components
- Two IR/serial ports on one 5-pole 3.5 mm captive screw: IR (using an IR emitter) or unidirectional RS-232 for control of AV system components
- Four low voltage relays on one 6-pole 3.5 mm captive screw: configurable for controlling lighting, controlling screens, or other device functions
- Four digital input/output ports on one 5-pole 3.5 mm captive screw: configurable for use as an interface with devices such as sensors, switches, LEDs, and relays
- One eBUS® port on a 4-pole 3.5 mm captive screw for connecting to eBUS devices
- Shall support the following protocols: ICMP (ping), IEEE 802.1X, IPv4, TCP, UDP, DHCP, DNS, HTTP, HTTPS, NTP, SFTP, SMTP, SNMP, SSH
- Shall support a Web-based AV resource management application that provides a means to manage, monitor, and control AV equipment
- Provide an internal real-time clock with a 30-year backup battery that is used to keep track of the date and time
- Shall support the addition of an Extron LinkLicense® for use of third party devices as primary control interfaces
- Provide front panel LED activity indicators for RS-232 status, RS-232/RS-422/RS-485 status, IR/serial status, digital I/O status, relay status, eBUS status, and network status
- Shall support control system synchronization to allow users to retain and recover configured endpoints in case of network or power failure
- Shall be configured using Extron Global Configurator® Plus or Extron Global Configurator Professional with support for the following:
- Provide support for up to eight configurable Extron TouchLink Pro touchpanels
- Provide support for up to eight configurable eBUS button panels
- Provide remote monitoring and control via Ethernet
- Provide the ability to create E-mail notifications
- Provide multiple levels of password protection
- Provide the ability to create schedules and monitors
- Support up to 32 Ethernet-controllable AV devices
- Support local variables and conditional logic
- Support grouping of multiple Extron IP Link® Pro xi control processors to function as one when configured with Global Configurator Professional
- Security Requirements
- Support SFTP and SSH for secure communication between the control processor and a TouchLink Pro touchpanel or Network Button Panel
- Support HTTPS and SSH for secure communication between the control processor and Extron Control App
- Support HTTPS for secure communication between the control processor and Extron Control for Web
- Support SSH for secure communication between the control processor and controlled device for programmed systems
- Support SFTP and SSH for secure communication between the control processor and the configuration or programming software
- Provide the option to modify administrator and user credentials
- Support security updates to maintain network health
- Require that a Secure Socket Layer (SSL) Certificate is installed to maintain system confidentiality and data integrity
- Support the installation of an owner furnished certificate with the following properties:
- Certificates shall include x.509 support
- Certificates shall include public / private key exchange
- Certificates shall support PEM encoding
- Extron shall furnish documentation that describes all supported network ports and services
- Provide AV system control connections
- Control/remote - RS-232 and IR Pass-Through Over Shielded CATx Requirements
- Provide connections for AV device control
- One (1) 3-pole 3.5 mm captive screw: IR pass-through to a DTP twisted pair receiver
- Support Ethernet insertion of RS-232 signals for transmission to a DTP endpoint
- Support RS-232 and IR transmission over shielded CATx up to 330 feet (100 meters)
- Provide connections for AV device control
- Control/remote – Presentation Switcher Requirements
- Provide control connections
- One (1) RJ-45: 10/100/1000Base-T Ethernet
- One (1) 3-pole 3.5 mm captive screw: RS-232
- One (1) Mini USB-B: USB 2.0
- Provide alternatives for configuration and operation
- On-screen menus navigated using front panel controls
- Product configuration software connected via Ethernet, USB, or RS-232
- Serial commands sent over Ethernet, RS-232 or USB connection
- Support disabling of front panel controls to prevent inadvertent or unauthorized changes to configuration settings
- Support triggering of standard CEC commands at main HDMI and DTP2 outputs
- Provide control connections
- General Requirements
- Enclosure shall be rack-mountable, full rack width, and 1RU in height
- Shall be equipped with an internal 100-240 VAC, 50/60 Hz universal power supply
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Video Input Requirements
- Approved device shall be the Extron IN1808 IPCP Q SA (part number 60-1615-92); no alternates or equals
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
IN1808 IPCP Q SA
- Provide a video scaling presentation switcher that shall support up to eight inputs and two simultaneous outputs for processing and switching of DisplayPort and HDMI video sources, with additional support for signal extension over shielded CATx cable
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
- Video Input Requirements
- Provide video input connections
- One (1) DisplayPort supporting DisplayPort SST - Single Stream Transport data rates up to 21.6 Gbps
- Five (5) HDMI supporting HDMI specifications including 4K/60 Deep Color, data rates up to 18 Gbps, and HD lossless audio formats
- Two (2) RJ-45 for DTP2 twisted pair
- Provide automatic detection of input video parameters
- Determine total pixels, active pixels, active lines, H/V starting points, H/V image positions, H/V image sizes, and video clock phase
- The user may selectively enable to disable automatic detection for each input
- Provide image adjustments for brightness, contrast, color, tint, detail, H/V positioning, and sizing
- Provide storage and recall of video parameters and picture settings
- Automatic memories for each video input
- Save video settings and picture adjustments without user intervention
- Automatically recall settings when the same video rate is encountered
- The user may selectively enable or disable automatic memories
- Manual user presets
- Save picture adjustments
- User presets may be saved and recalled using front panel controls
- User presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Manual input presets
- Save video settings and picture adjustments
- Input presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Automatic memories for each video input
- Provide automatic 3:2 and 2:2 pulldown detection
- Provide video input connections
- Video Output Requirements
- Provide one (1) HDMI for loop-through without video scaling, selectable for any video input.
- Provide scaled video output connections
- One (1) HDMI
- One (1) RJ-45 for DTP2 twisted pair
- Provide a range of selectable video output rates from 640x480 to 4096x2160 @ 60 Hz
- Support custom user-defined output resolutions via EDID management
- Provide image scaling and video format conversion with 30-bit precision and 4:4:4 chroma sampling
- Provide motion adaptive deinterlacing for signals up to 1080i
- Provide aspect ratio control
- When in FILL mode, the video image shall always fill the output screen without letterbox or pillarbox
- When in FOLLOW mode, the video image on the output screen shall always preserve the aspect ratio of the input signals without distortion
- Provide internal test patterns for calibration and setup
- Support image freeze via Ethernet, RS-232 or USB connection
- Support upload and placement of a custom logo graphic at any position on the video output
- Support logo placement as a foreground image
- Shall support uploading logo graphics in BMP, JPG, PNG, GIF, or TIFF format
- Shall support displaying full screen images up to 4096x2160 resolution
- Shall support up to 16 logo presets
- Shall support keying with selectable effects including transparency, color key, level key, and alpha key
- Support automatic muting of video and sync output when no video input signal is present
- Provide a choice to generate a blue screen or a black screen before disabling sync
- Provide a configurable timeout period before disabling sync
- The user may selectively enable or disable automatic muting of sync output
- Provide a low power standby state selectable via Ethernet, RS-232 or USB
- Support the connection of DVI displays that do not recognize HDMI-specific formats
- Automatically enable or disable embedded TMDS audio and InfoFrames
- Automatically set the correct color space
- Support selection of output color space as RGB or component video
- Switching Requirements
- Provide configurable automatic switching modes between input sources
- Last connected: always switch to the last active connected input
- Configurable priority: switching priority may be assigned arbitrarily for any combination of the four inputs
- Provide selectable transition effects when switching inputs
- Seamless Cut: video output shall freeze, then cut to the newly selected input source
- Seamless Fade: video output shall freeze, then fade into the newly selected input source
- Cut through black: video output shall cut to black, then cut to the newly selected input source
- Fade through black: video output shall fade to black, then fade into the newly selected input source
- Accompanying audio shall ramp down, then ramp up to match the transition effect
- Provide configurable automatic switching modes between input sources
- EDID Requirements
- Provide automatic EDID management between connected devices
- Provide a set of pre-stored EDID files
- Support capture of EDID from any connected display
- Support user uploading of custom-generated EDID files
- Support assignment of any pre-stored, captured, or custom uploaded EDID file to any input connection
- Provide automatic EDID management between connected devices
- HDCP Requirements
- The unit shall be HDCP 2.2 compliant
- Provide authentication and maintain continuous verification of HDCP key exchange with connected sink devices
- Provide authentication and maintain continuous verification of HDCP key exchange with connected source devices
- Provide the option to disable HDCP processing at video inputs 2 through 8 when passing unencrypted content
- Provide selectable, human-readable visual confirmation of HDCP compliance when encrypted content is routed to a non-HDCP compliant display
- When enabled, the video output shall be a solid green color and an on-screen message stating “HDCP CONTENT” shall be displayed
- When enabled, the option shall be provided to display a user-provided image in place of the green video output
- When disabled, the output shall be muted
- Provide real-time verification of HDCP status for each video input and output
- Directly readable on front panel LEDs
- Electronically accessible over Ethernet, RS-232 or USB connection
- The unit shall be HDCP 2.2 compliant
- DTP2 Twisted pair requirements
- Provide signal transmission distance capability of 330 feet (100 meters) for all supported video resolutions using a shielded CATx cable
- Support video, audio, RS-232, IR, and power transmission over a single shielded CATx cable
- Shall be compatible with CATx shielded twisted pair cable, and Extron XTP DTP 24 shielded twisted pair cable
- Support computer and video resolutions up to 3840x2160/60 at 4:4:4 chroma sampling
- Support stereo audio pass-through signals
- Shall actively buffer DDC channels
- Shall be configurable for compatibility with
- Extron DTP inputs
- Extron DTP2 inputs
- Extron XTP matrix switcher inputs
- HDBaseT inputs
- Provide power to remote DTP or DTP2 endpoint connected over the shielded CATx cable.
- Audio Requirements
- Provide audio input connections
- One (1) DisplayPort, embedded
- Five (5) HDMI, embedded
- Two (2) 5-pole 3.5 mm captive screw, balanced/unbalanced line level analog stereo
- Two (2) 3-pole 3.5 mm captive screw, balanced/unbalanced mic/line level with +48 volt phantom power
- Provide audio output connections
- One (1) 4-pole, 5 mm captive screw, speaker level connector for stereo signal or dual mono
- Two (2) 5-pole 3.5 mm captive screw, with output level control and configurable for balanced/unbalanced, analog stereo or dual mono
- One (1) HDMI, embedded and with output level control for two-channel PCM
- One (1) RJ-45 for DTP2 twisted pair transmitting both:
- Embedded digital audio
- Pass-through stereo audio
- Provide stereo amplification for low impedance speaker systems
- Support one stereo speaker level signal or two mono speaker level signals on one 4-pole, 5 mm screw-lock captive screw connector
- Provide a total of 100 watts rms output power with 50 watts rms per channel into 4 ohms, or 25 watts rms per channel into 8 ohms measured at 1 kHz with 0.1% THD
- Provide a THD+N measurement of less than 0.1 % measured at 3 dB below clipping
- Provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Utilize an efficient Class D amplifier design
- Provide Class D Ripple Suppression technology
- Provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain with a slow attack and fast release to eliminate clipping distortion
- Provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults
- Support embedding of the analog audio input signal on the HDMI and DTP2 outputs
- Support extraction of two-channel PCM embedded audio signals to analog audio outputs, or pass bitstream audio to the HDMI and DTP2 outputs
- Provide the capability for all video inputs to share a common analog audio input
- Provide a delay in the audio output to match the corresponding video processing delay
- Provide gain and attenuation adjustments for analog input audio
- Support individual muting of the analog stereo or embedded digital audio outputs
- DSP Requirements
- Provide digital audio processing tools including gain, mixing, parametric EQ, filtering, dynamics, and ducking
- Provide adjustable, automatic ducking of program audio when a signal is detected on microphone inputs
- Provide DSP configuration and parameter adjustments through the product configuration software
- Provide real-time level meters for inputs and outputs in the product configuration software
- Provide live DSP parameter adjustments while they are heard or metered in real-time
- Provide user presets for saving and recalling DSP parameters
- Support storage and playback of up to 16 audio files at any audio output.
- Provide audio input connections
- Integrated Control Processor Requirements
- Provide AV system control connections
- Three RJ-45: 10/100/1000Base-T Ethernet, half/full duplex with auto-detect for connection to a LAN and include link and activity LED indicators located on the left and right of each jack for troubleshooting network issues, these ports will be designated as AV LAN ports allowing for AV devices to be isolated from a corporate network.
- AV LAN ports shall support a DHCP server that can distribute 50 dynamic IP addresses with a 24-hour lease
- One RJ-45: 10/100/1000Base-T, half/full duplex with auto-detect for connection to a LAN or WAN and includes link and activity LED indicators located on the left and right of the jack for troubleshooting network issues.
- Two 3-pole 3.5 mm captive screw: RS-232, configurable for unidirectional or bidirectional control of AV system components
- One 5-pole 3.5 mm captive screw: RS-232/RS-422/RS-485, configurable for unidirectional or bidirectional control of AV system components
- Two IR/serial ports on one 5-pole 3.5 mm captive screw: IR (using an IR emitter) or unidirectional RS-232 for control of AV system components
- Four low voltage relays on one 6-pole 3.5 mm captive screw: configurable for controlling lighting, controlling screens, or other device functions
- Four digital input/output ports on one 5-pole 3.5 mm captive screw: configurable for use as an interface with devices such as sensors, switches, LEDs, and relays
- One eBUS® port on a 4-pole 3.5 mm captive screw for connecting to eBUS devices
- Shall support the following protocols: ICMP (ping), IEEE 802.1X, IPv4, TCP, UDP, DHCP, DNS, HTTP, HTTPS, NTP, SFTP, SMTP, SNMP, SSH
- Shall support a Web-based AV resource management application that provides a means to manage, monitor, and control AV equipment
- Provide an internal real-time clock with a 30-year backup battery that is used to keep track of the date and time
- Shall support the addition of an Extron LinkLicense® for use of third party devices as primary control interfaces
- Provide front panel LED activity indicators for RS-232 status, RS-232/RS-422/RS-485 status, IR/serial status, digital I/O status, relay status, eBUS status, and network status
- Shall support control system synchronization to allow users to retain and recover configured endpoints in case of network or power failure
- Shall be configured using Extron Global Configurator® Plus or Extron Global Configurator Professional with support for the following:
- Provide support for up to eight configurable Extron TouchLink Pro touchpanels
- Provide support for up to eight configurable eBUS button panels
- Provide remote monitoring and control via Ethernet
- Provide the ability to create E-mail notifications
- Provide multiple levels of password protection
- Provide the ability to create schedules and monitors
- Support up to 32 Ethernet-controllable AV devices
- Support local variables and conditional logic
- Support grouping of multiple Extron IP Link® Pro xi control processors to function as one when configured with Global Configurator Professional
- Security Requirements
- Support SFTP and SSH for secure communication between the control processor and a TouchLink Pro touchpanel or Network Button Panel
- Support HTTPS and SSH for secure communication between the control processor and Extron Control App
- Support HTTPS for secure communication between the control processor and Extron Control for Web
- Support SSH for secure communication between the control processor and controlled device for programmed systems
- Support SFTP and SSH for secure communication between the control processor and the configuration or programming software
- Provide the option to modify administrator and user credentials
- Support security updates to maintain network health
- Require that a Secure Socket Layer (SSL) Certificate is installed to maintain system confidentiality and data integrity
- Support the installation of an owner furnished certificate with the following properties:
- Certificates shall include x.509 support
- Certificates shall include public / private key exchange
- Certificates shall support PEM encoding
- Extron shall furnish documentation that describes all supported network ports and services
- Provide AV system control connections
- Control/remote - RS-232 and IR Pass-Through Over Shielded CATx Requirements
- Provide connections for AV device control
- One (1) 3-pole 3.5 mm captive screw: IR pass-through to a DTP twisted pair receiver
- Support Ethernet insertion of RS-232 signals for transmission to a DTP endpoint
- Support RS-232 and IR transmission over shielded CATx up to 330 feet (100 meters)
- Provide connections for AV device control
- Control/remote – Presentation Switcher Requirements
- Provide control connections
- One (1) RJ-45: 10/100/1000Base-T Ethernet
- One (1) 3-pole 3.5 mm captive screw: RS-232
- One (1) Mini USB-B: USB 2.0
- Provide alternatives for configuration and operation
- On-screen menus navigated using front panel controls
- Product configuration software connected via Ethernet, USB, or RS-232
- Serial commands sent over Ethernet, RS-232 or USB connection
- Support disabling of front panel controls to prevent inadvertent or unauthorized changes to configuration settings
- Support triggering of standard CEC commands at main HDMI and DTP2 outputs
- Provide control connections
- General Requirements
- Enclosure shall be rack-mountable, full rack width, and 1RU in height
- Shall be equipped with an internal 100-240 VAC, 50/60 Hz universal power supply
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Video Input Requirements
- Approved device shall be the Extron IN1808 IPCP Q SA (part number 60-1615-92); no alternates or equals
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
IN1808 IPCP Q SA
- Provide a video scaling presentation switcher that shall support up to eight inputs and two simultaneous outputs for processing and switching of DisplayPort and HDMI video sources, with additional support for signal extension over shielded CATx cable
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
- Video Input Requirements
- Provide video input connections
- One (1) DisplayPort supporting DisplayPort SST - Single Stream Transport data rates up to 21.6 Gbps
- Five (5) HDMI supporting HDMI specifications including 4K/60 Deep Color, data rates up to 18 Gbps, and HD lossless audio formats
- Two (2) RJ-45 for DTP2 twisted pair
- Provide automatic detection of input video parameters
- Determine total pixels, active pixels, active lines, H/V starting points, H/V image positions, H/V image sizes, and video clock phase
- The user may selectively enable to disable automatic detection for each input
- Provide image adjustments for brightness, contrast, color, tint, detail, H/V positioning, and sizing
- Provide storage and recall of video parameters and picture settings
- Automatic memories for each video input
- Save video settings and picture adjustments without user intervention
- Automatically recall settings when the same video rate is encountered
- The user may selectively enable or disable automatic memories
- Manual user presets
- Save picture adjustments
- User presets may be saved and recalled using front panel controls
- User presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Manual input presets
- Save video settings and picture adjustments
- Input presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Automatic memories for each video input
- Provide automatic 3:2 and 2:2 pulldown detection
- Provide video input connections
- Video Output Requirements
- Provide one (1) HDMI for loop-through without video scaling, selectable for any video input.
- Provide scaled video output connections
- One (1) HDMI
- One (1) RJ-45 for DTP2 twisted pair
- Provide a range of selectable video output rates from 640x480 to 4096x2160 @ 60 Hz
- Support custom user-defined output resolutions via EDID management
- Provide image scaling and video format conversion with 30-bit precision and 4:4:4 chroma sampling
- Provide motion adaptive deinterlacing for signals up to 1080i
- Provide aspect ratio control
- When in FILL mode, the video image shall always fill the output screen without letterbox or pillarbox
- When in FOLLOW mode, the video image on the output screen shall always preserve the aspect ratio of the input signals without distortion
- Provide internal test patterns for calibration and setup
- Support image freeze via Ethernet, RS-232 or USB connection
- Support upload and placement of a custom logo graphic at any position on the video output
- Support logo placement as a foreground image
- Shall support uploading logo graphics in BMP, JPG, PNG, GIF, or TIFF format
- Shall support displaying full screen images up to 4096x2160 resolution
- Shall support up to 16 logo presets
- Shall support keying with selectable effects including transparency, color key, level key, and alpha key
- Support automatic muting of video and sync output when no video input signal is present
- Provide a choice to generate a blue screen or a black screen before disabling sync
- Provide a configurable timeout period before disabling sync
- The user may selectively enable or disable automatic muting of sync output
- Provide a low power standby state selectable via Ethernet, RS-232 or USB
- Support the connection of DVI displays that do not recognize HDMI-specific formats
- Automatically enable or disable embedded TMDS audio and InfoFrames
- Automatically set the correct color space
- Support selection of output color space as RGB or component video
- Switching Requirements
- Provide configurable automatic switching modes between input sources
- Last connected: always switch to the last active connected input
- Configurable priority: switching priority may be assigned arbitrarily for any combination of the four inputs
- Provide selectable transition effects when switching inputs
- Seamless Cut: video output shall freeze, then cut to the newly selected input source
- Seamless Fade: video output shall freeze, then fade into the newly selected input source
- Cut through black: video output shall cut to black, then cut to the newly selected input source
- Fade through black: video output shall fade to black, then fade into the newly selected input source
- Accompanying audio shall ramp down, then ramp up to match the transition effect
- Provide configurable automatic switching modes between input sources
- EDID Requirements
- Provide automatic EDID management between connected devices
- Provide a set of pre-stored EDID files
- Support capture of EDID from any connected display
- Support user uploading of custom-generated EDID files
- Support assignment of any pre-stored, captured, or custom uploaded EDID file to any input connection
- Provide automatic EDID management between connected devices
- HDCP Requirements
- The unit shall be HDCP 2.2 compliant
- Provide authentication and maintain continuous verification of HDCP key exchange with connected sink devices
- Provide authentication and maintain continuous verification of HDCP key exchange with connected source devices
- Provide the option to disable HDCP processing at video inputs 2 through 8 when passing unencrypted content
- Provide selectable, human-readable visual confirmation of HDCP compliance when encrypted content is routed to a non-HDCP compliant display
- When enabled, the video output shall be a solid green color and an on-screen message stating “HDCP CONTENT” shall be displayed
- When enabled, the option shall be provided to display a user-provided image in place of the green video output
- When disabled, the output shall be muted
- Provide real-time verification of HDCP status for each video input and output
- Directly readable on front panel LEDs
- Electronically accessible over Ethernet, RS-232 or USB connection
- The unit shall be HDCP 2.2 compliant
- DTP2 Twisted pair requirements
- Provide signal transmission distance capability of 330 feet (100 meters) for all supported video resolutions using a shielded CATx cable
- Support video, audio, RS-232, IR, and power transmission over a single shielded CATx cable
- Shall be compatible with CATx shielded twisted pair cable, and Extron XTP DTP 24 shielded twisted pair cable
- Support computer and video resolutions up to 3840x2160/60 at 4:4:4 chroma sampling
- Support stereo audio pass-through signals
- Shall actively buffer DDC channels
- Shall be configurable for compatibility with
- Extron DTP inputs
- Extron DTP2 inputs
- Extron XTP matrix switcher inputs
- HDBaseT inputs
- Provide power to remote DTP or DTP2 endpoint connected over the shielded CATx cable.
- Audio Requirements
- Provide audio input connections
- One (1) DisplayPort, embedded
- Five (5) HDMI, embedded
- Two (2) 5-pole 3.5 mm captive screw, balanced/unbalanced line level analog stereo
- Two (2) 3-pole 3.5 mm captive screw, balanced/unbalanced mic/line level with +48 volt phantom power
- Provide audio output connections
- One (1) 4-pole, 5 mm captive screw, speaker level connector for stereo signal or dual mono
- Two (2) 5-pole 3.5 mm captive screw, with output level control and configurable for balanced/unbalanced, analog stereo or dual mono
- One (1) HDMI, embedded and with output level control for two-channel PCM
- One (1) RJ-45 for DTP2 twisted pair transmitting both:
- Embedded digital audio
- Pass-through stereo audio
- Provide stereo amplification for low impedance speaker systems
- Support one stereo speaker level signal or two mono speaker level signals on one 4-pole, 5 mm screw-lock captive screw connector
- Provide a total of 100 watts rms output power with 50 watts rms per channel into 4 ohms, or 25 watts rms per channel into 8 ohms measured at 1 kHz with 0.1% THD
- Provide a THD+N measurement of less than 0.1 % measured at 3 dB below clipping
- Provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Utilize an efficient Class D amplifier design
- Provide Class D Ripple Suppression technology
- Provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain with a slow attack and fast release to eliminate clipping distortion
- Provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults
- Support embedding of the analog audio input signal on the HDMI and DTP2 outputs
- Support extraction of two-channel PCM embedded audio signals to analog audio outputs, or pass bitstream audio to the HDMI and DTP2 outputs
- Provide the capability for all video inputs to share a common analog audio input
- Provide a delay in the audio output to match the corresponding video processing delay
- Provide gain and attenuation adjustments for analog input audio
- Support individual muting of the analog stereo or embedded digital audio outputs
- DSP Requirements
- Provide digital audio processing tools including gain, mixing, parametric EQ, filtering, dynamics, and ducking
- Provide adjustable, automatic ducking of program audio when a signal is detected on microphone inputs
- Provide DSP configuration and parameter adjustments through the product configuration software
- Provide real-time level meters for inputs and outputs in the product configuration software
- Provide live DSP parameter adjustments while they are heard or metered in real-time
- Provide user presets for saving and recalling DSP parameters
- Support storage and playback of up to 16 audio files at any audio output.
- Provide audio input connections
- Integrated Control Processor Requirements
- Provide AV system control connections
- Three RJ-45: 10/100/1000Base-T Ethernet, half/full duplex with auto-detect for connection to a LAN and include link and activity LED indicators located on the left and right of each jack for troubleshooting network issues, these ports will be designated as AV LAN ports allowing for AV devices to be isolated from a corporate network.
- AV LAN ports shall support a DHCP server that can distribute 50 dynamic IP addresses with a 24-hour lease
- One RJ-45: 10/100/1000Base-T, half/full duplex with auto-detect for connection to a LAN or WAN and includes link and activity LED indicators located on the left and right of the jack for troubleshooting network issues.
- Two 3-pole 3.5 mm captive screw: RS-232, configurable for unidirectional or bidirectional control of AV system components
- One 5-pole 3.5 mm captive screw: RS-232/RS-422/RS-485, configurable for unidirectional or bidirectional control of AV system components
- Two IR/serial ports on one 5-pole 3.5 mm captive screw: IR (using an IR emitter) or unidirectional RS-232 for control of AV system components
- Four low voltage relays on one 6-pole 3.5 mm captive screw: configurable for controlling lighting, controlling screens, or other device functions
- Four digital input/output ports on one 5-pole 3.5 mm captive screw: configurable for use as an interface with devices such as sensors, switches, LEDs, and relays
- One eBUS® port on a 4-pole 3.5 mm captive screw for connecting to eBUS devices
- Shall support the following protocols: ICMP (ping), IEEE 802.1X, IPv4, TCP, UDP, DHCP, DNS, HTTP, HTTPS, NTP, SFTP, SMTP, SNMP, SSH
- Shall support a Web-based AV resource management application that provides a means to manage, monitor, and control AV equipment
- Provide an internal real-time clock with a 30-year backup battery that is used to keep track of the date and time
- Shall include an Extron LinkLicense® for use of third party devices as primary control interfaces
- Provide front panel LED activity indicators for RS-232 status, RS-232/RS-422/RS-485 status, IR/serial status, digital I/O status, relay status, eBUS status, and network status
- Shall support control system synchronization to allow users to retain and recover configured endpoints in case of network or power failure
- Shall be configured using Extron Global Configurator® Plus or Extron Global Configurator Professional with support for the following:
- Provide support for up to eight configurable Extron TouchLink Pro touchpanels
- Provide support for up to eight configurable eBUS button panels
- Provide remote monitoring and control via Ethernet
- Provide the ability to create E-mail notifications
- Provide multiple levels of password protection
- Provide the ability to create schedules and monitors
- Support up to 32 Ethernet-controllable AV devices
- Support local variables and conditional logic
- Support grouping of multiple Extron IP Link® Pro xi control processors to function as one when configured with Global Configurator Professional
- Security Requirements
- Support SFTP and SSH for secure communication between the control processor and a TouchLink Pro touchpanel or Network Button Panel
- Support HTTPS and SSH for secure communication between the control processor and Extron Control App
- Support HTTPS for secure communication between the control processor and Extron Control for Web
- Support SSH for secure communication between the control processor and controlled device for programmed systems
- Support SFTP and SSH for secure communication between the control processor and the configuration or programming software
- Provide the option to modify administrator and user credentials
- Support security updates to maintain network health
- Require that a Secure Socket Layer (SSL) Certificate is installed to maintain system confidentiality and data integrity
- Support the installation of an owner furnished certificate with the following properties:
- Certificates shall include x.509 support
- Certificates shall include public / private key exchange
- Certificates shall support PEM encoding
- Extron shall furnish documentation that describes all supported network ports and services
- Provide AV system control connections
- Control/remote - RS-232 and IR Pass-Through Over Shielded CATx Requirements
- Provide connections for AV device control
- One (1) 3-pole 3.5 mm captive screw: IR pass-through to a DTP twisted pair receiver
- Support Ethernet insertion of RS-232 signals for transmission to a DTP endpoint
- Support RS-232 and IR transmission over shielded CATx up to 330 feet (100 meters)
- Provide connections for AV device control
- Control/remote – Presentation Switcher Requirements
- Provide control connections
- One (1) RJ-45: 10/100/1000Base-T Ethernet
- One (1) 3-pole 3.5 mm captive screw: RS-232
- One (1) Mini USB-B: USB 2.0
- Provide alternatives for configuration and operation
- On-screen menus navigated using front panel controls
- Product configuration software connected via Ethernet, USB, or RS-232
- Serial commands sent over Ethernet, RS-232 or USB connection
- Support disabling of front panel controls to prevent inadvertent or unauthorized changes to configuration settings
- Support triggering of standard CEC commands at main HDMI and DTP2 outputs
- Provide control connections
- General Requirements
- Enclosure shall be rack-mountable, full rack width, and 2RU in height
- Shall be equipped with an internal 100-240 VAC, 50/60 Hz universal power supply
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Video Input Requirements
- Approved device shall be the Extron IN1808 IPCP Q SA (part number 60-1615-92A); no alternates or equals
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
IN1808 IPCP Q SA
- Provide a video scaling presentation switcher that shall support up to eight inputs and two simultaneous outputs for processing and switching of DisplayPort and HDMI video sources, with additional support for signal extension over shielded CATx cable
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
- Video Input Requirements
- Provide video input connections
- One (1) DisplayPort supporting DisplayPort SST - Single Stream Transport data rates up to 21.6 Gbps
- Five (5) HDMI supporting HDMI specifications including 4K/60 Deep Color, data rates up to 18 Gbps, and HD lossless audio formats
- Two (2) RJ-45 for DTP2 twisted pair
- Provide automatic detection of input video parameters
- Determine total pixels, active pixels, active lines, H/V starting points, H/V image positions, H/V image sizes, and video clock phase
- The user may selectively enable to disable automatic detection for each input
- Provide image adjustments for brightness, contrast, color, tint, detail, H/V positioning, and sizing
- Provide storage and recall of video parameters and picture settings
- Automatic memories for each video input
- Save video settings and picture adjustments without user intervention
- Automatically recall settings when the same video rate is encountered
- The user may selectively enable or disable automatic memories
- Manual user presets
- Save picture adjustments
- User presets may be saved and recalled using front panel controls
- User presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Manual input presets
- Save video settings and picture adjustments
- Input presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Automatic memories for each video input
- Provide automatic 3:2 and 2:2 pulldown detection
- Provide video input connections
- Video Output Requirements
- Provide one (1) HDMI for loop-through without video scaling, selectable for any video input.
- Provide scaled video output connections
- One (1) HDMI
- One (1) RJ-45 for DTP2 twisted pair
- Provide a range of selectable video output rates from 640x480 to 4096x2160 @ 60 Hz
- Support custom user-defined output resolutions via EDID management
- Provide image scaling and video format conversion with 30-bit precision and 4:4:4 chroma sampling
- Provide motion adaptive deinterlacing for signals up to 1080i
- Provide aspect ratio control
- When in FILL mode, the video image shall always fill the output screen without letterbox or pillarbox
- When in FOLLOW mode, the video image on the output screen shall always preserve the aspect ratio of the input signals without distortion
- Provide internal test patterns for calibration and setup
- Support image freeze via Ethernet, RS-232 or USB connection
- Support upload and placement of a custom logo graphic at any position on the video output
- Support logo placement as a foreground image
- Shall support uploading logo graphics in BMP, JPG, PNG, GIF, or TIFF format
- Shall support displaying full screen images up to 4096x2160 resolution
- Shall support up to 16 logo presets
- Shall support keying with selectable effects including transparency, color key, level key, and alpha key
- Support automatic muting of video and sync output when no video input signal is present
- Provide a choice to generate a blue screen or a black screen before disabling sync
- Provide a configurable timeout period before disabling sync
- The user may selectively enable or disable automatic muting of sync output
- Provide a low power standby state selectable via Ethernet, RS-232 or USB
- Support the connection of DVI displays that do not recognize HDMI-specific formats
- Automatically enable or disable embedded TMDS audio and InfoFrames
- Automatically set the correct color space
- Support selection of output color space as RGB or component video
- Switching Requirements
- Provide configurable automatic switching modes between input sources
- Last connected: always switch to the last active connected input
- Configurable priority: switching priority may be assigned arbitrarily for any combination of the four inputs
- Provide selectable transition effects when switching inputs
- Seamless Cut: video output shall freeze, then cut to the newly selected input source
- Seamless Fade: video output shall freeze, then fade into the newly selected input source
- Cut through black: video output shall cut to black, then cut to the newly selected input source
- Fade through black: video output shall fade to black, then fade into the newly selected input source
- Accompanying audio shall ramp down, then ramp up to match the transition effect
- Provide configurable automatic switching modes between input sources
- EDID Requirements
- Provide automatic EDID management between connected devices
- Provide a set of pre-stored EDID files
- Support capture of EDID from any connected display
- Support user uploading of custom-generated EDID files
- Support assignment of any pre-stored, captured, or custom uploaded EDID file to any input connection
- Provide automatic EDID management between connected devices
- HDCP Requirements
- The unit shall be HDCP 2.2 compliant
- Provide authentication and maintain continuous verification of HDCP key exchange with connected sink devices
- Provide authentication and maintain continuous verification of HDCP key exchange with connected source devices
- Provide the option to disable HDCP processing at video inputs 2 through 8 when passing unencrypted content
- Provide selectable, human-readable visual confirmation of HDCP compliance when encrypted content is routed to a non-HDCP compliant display
- When enabled, the video output shall be a solid green color and an on-screen message stating “HDCP CONTENT” shall be displayed
- When enabled, the option shall be provided to display a user-provided image in place of the green video output
- When disabled, the output shall be muted
- Provide real-time verification of HDCP status for each video input and output
- Directly readable on front panel LEDs
- Electronically accessible over Ethernet, RS-232 or USB connection
- The unit shall be HDCP 2.2 compliant
- DTP2 Twisted pair requirements
- Provide signal transmission distance capability of 330 feet (100 meters) for all supported video resolutions using a shielded CATx cable
- Support video, audio, RS-232, IR, and power transmission over a single shielded CATx cable
- Shall be compatible with CATx shielded twisted pair cable, and Extron XTP DTP 24 shielded twisted pair cable
- Support computer and video resolutions up to 3840x2160/60 at 4:4:4 chroma sampling
- Support stereo audio pass-through signals
- Shall actively buffer DDC channels
- Shall be configurable for compatibility with
- Extron DTP inputs
- Extron DTP2 inputs
- Extron XTP matrix switcher inputs
- HDBaseT inputs
- Provide power to remote DTP or DTP2 endpoint connected over the shielded CATx cable.
- Audio Requirements
- Provide audio input connections
- One (1) DisplayPort, embedded
- Five (5) HDMI, embedded
- Two (2) 5-pole 3.5 mm captive screw, balanced/unbalanced line level analog stereo
- Two (2) 3-pole 3.5 mm captive screw, balanced/unbalanced mic/line level with +48 volt phantom power
- Provide audio output connections
- One (1) 4-pole, 5 mm captive screw, speaker level connector for stereo signal or dual mono
- Two (2) 5-pole 3.5 mm captive screw, with output level control and configurable for balanced/unbalanced, analog stereo or dual mono
- One (1) HDMI, embedded and with output level control for two-channel PCM
- One (1) RJ-45 for DTP2 twisted pair transmitting both:
- Embedded digital audio
- Pass-through stereo audio
- Provide stereo amplification for low impedance speaker systems
- Support one stereo speaker level signal or two mono speaker level signals on one 4-pole, 5 mm screw-lock captive screw connector
- Provide a total of 100 watts rms output power with 50 watts rms per channel into 4 ohms, or 25 watts rms per channel into 8 ohms measured at 1 kHz with 0.1% THD
- Provide a THD+N measurement of less than 0.1 % measured at 3 dB below clipping
- Provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Utilize an efficient Class D amplifier design
- Provide Class D Ripple Suppression technology
- Provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain with a slow attack and fast release to eliminate clipping distortion
- Provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults
- Support embedding of the analog audio input signal on the HDMI and DTP2 outputs
- Support extraction of two-channel PCM embedded audio signals to analog audio outputs, or pass bitstream audio to the HDMI and DTP2 outputs
- Provide the capability for all video inputs to share a common analog audio input
- Provide a delay in the audio output to match the corresponding video processing delay
- Provide gain and attenuation adjustments for analog input audio
- Support individual muting of the analog stereo or embedded digital audio outputs
- DSP Requirements
- Provide digital audio processing tools including gain, mixing, parametric EQ, filtering, dynamics, and ducking
- Provide adjustable, automatic ducking of program audio when a signal is detected on microphone inputs
- Provide DSP configuration and parameter adjustments through the product configuration software
- Provide real-time level meters for inputs and outputs in the product configuration software
- Provide live DSP parameter adjustments while they are heard or metered in real-time
- Provide user presets for saving and recalling DSP parameters
- Support storage and playback of up to 16 audio files at any audio output.
- Provide audio input connections
- Integrated Control Processor Requirements
- Provide AV system control connections
- Three RJ-45: 10/100/1000Base-T Ethernet, half/full duplex with auto-detect for connection to a LAN and include link and activity LED indicators located on the left and right of each jack for troubleshooting network issues, these ports will be designated as AV LAN ports allowing for AV devices to be isolated from a corporate network.
- AV LAN ports shall support a DHCP server that can distribute 50 dynamic IP addresses with a 24-hour lease
- One RJ-45: 10/100/1000Base-T, half/full duplex with auto-detect for connection to a LAN or WAN and includes link and activity LED indicators located on the left and right of the jack for troubleshooting network issues.
- Two 3-pole 3.5 mm captive screw: RS-232, configurable for unidirectional or bidirectional control of AV system components
- One 5-pole 3.5 mm captive screw: RS-232/RS-422/RS-485, configurable for unidirectional or bidirectional control of AV system components
- Two IR/serial ports on one 5-pole 3.5 mm captive screw: IR (using an IR emitter) or unidirectional RS-232 for control of AV system components
- Four low voltage relays on one 6-pole 3.5 mm captive screw: configurable for controlling lighting, controlling screens, or other device functions
- Four digital input/output ports on one 5-pole 3.5 mm captive screw: configurable for use as an interface with devices such as sensors, switches, LEDs, and relays
- One eBUS® port on a 4-pole 3.5 mm captive screw for connecting to eBUS devices
- Shall support the following protocols: ICMP (ping), IEEE 802.1X, IPv4, TCP, UDP, DHCP, DNS, HTTP, HTTPS, NTP, SFTP, SMTP, SNMP, SSH
- Shall support a Web-based AV resource management application that provides a means to manage, monitor, and control AV equipment
- Provide an internal real-time clock with a 30-year backup battery that is used to keep track of the date and time
- Shall include an Extron LinkLicense® for use of third party devices as primary control interfaces
- Provide front panel LED activity indicators for RS-232 status, RS-232/RS-422/RS-485 status, IR/serial status, digital I/O status, relay status, eBUS status, and network status
- Shall support control system synchronization to allow users to retain and recover configured endpoints in case of network or power failure
- Shall be configured using Extron Global Configurator® Plus or Extron Global Configurator Professional with support for the following:
- Provide support for up to eight configurable Extron TouchLink Pro touchpanels
- Provide support for up to eight configurable eBUS button panels
- Provide remote monitoring and control via Ethernet
- Provide the ability to create E-mail notifications
- Provide multiple levels of password protection
- Provide the ability to create schedules and monitors
- Support up to 32 Ethernet-controllable AV devices
- Support local variables and conditional logic
- Support grouping of multiple Extron IP Link® Pro xi control processors to function as one when configured with Global Configurator Professional
- Security Requirements
- Support SFTP and SSH for secure communication between the control processor and a TouchLink Pro touchpanel or Network Button Panel
- Support HTTPS and SSH for secure communication between the control processor and Extron Control App
- Support HTTPS for secure communication between the control processor and Extron Control for Web
- Support SSH for secure communication between the control processor and controlled device for programmed systems
- Support SFTP and SSH for secure communication between the control processor and the configuration or programming software
- Provide the option to modify administrator and user credentials
- Support security updates to maintain network health
- Require that a Secure Socket Layer (SSL) Certificate is installed to maintain system confidentiality and data integrity
- Support the installation of an owner furnished certificate with the following properties:
- Certificates shall include x.509 support
- Certificates shall include public / private key exchange
- Certificates shall support PEM encoding
- Extron shall furnish documentation that describes all supported network ports and services
- Provide AV system control connections
- Control/remote - RS-232 and IR Pass-Through Over Shielded CATx Requirements
- Provide connections for AV device control
- One (1) 3-pole 3.5 mm captive screw: IR pass-through to a DTP twisted pair receiver
- Support Ethernet insertion of RS-232 signals for transmission to a DTP endpoint
- Support RS-232 and IR transmission over shielded CATx up to 330 feet (100 meters)
- Provide connections for AV device control
- Control/remote – Presentation Switcher Requirements
- Provide control connections
- One (1) RJ-45: 10/100/1000Base-T Ethernet
- One (1) 3-pole 3.5 mm captive screw: RS-232
- One (1) Mini USB-B: USB 2.0
- Provide alternatives for configuration and operation
- On-screen menus navigated using front panel controls
- Product configuration software connected via Ethernet, USB, or RS-232
- Serial commands sent over Ethernet, RS-232 or USB connection
- Support disabling of front panel controls to prevent inadvertent or unauthorized changes to configuration settings
- Support triggering of standard CEC commands at main HDMI and DTP2 outputs
- Provide control connections
- General Requirements
- Enclosure shall be rack-mountable, full rack width, and 2RU in height
- Shall be equipped with an internal 100-240 VAC, 50/60 Hz universal power supply
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Video Input Requirements
- Approved device shall be the Extron IN1808 IPCP Q SA (part number 60-1615-92A); no alternates or equals
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
IN1808 IPCP Q MA 70
- Provide a video scaling presentation switcher that shall support up to eight inputs and two simultaneous outputs for processing and switching of DisplayPort and HDMI video sources, with additional support for signal extension over shielded CATx cable
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
- Video Input Requirements
- Provide video input connections
- One (1) DisplayPort supporting DisplayPort SST - Single Stream Transport data rates up to 21.6 Gbps
- Five (5) HDMI supporting HDMI specifications including 4K/60 Deep Color, data rates up to 18 Gbps, and HD lossless audio formats
- Two (2) RJ-45 for DTP2 twisted pair
- Provide automatic detection of input video parameters
- Determine total pixels, active pixels, active lines, H/V starting points, H/V image positions, H/V image sizes, and video clock phase
- The user may selectively enable to disable automatic detection for each input
- Provide image adjustments for brightness, contrast, color, tint, detail, H/V positioning, and sizing
- Provide storage and recall of video parameters and picture settings
- Automatic memories for each video input
- Save video settings and picture adjustments without user intervention
- Automatically recall settings when the same video rate is encountered
- The user may selectively enable or disable automatic memories
- Manual user presets
- Save picture adjustments
- User presets may be saved and recalled using front panel controls
- User presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Manual input presets
- Save video settings and picture adjustments
- Input presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Automatic memories for each video input
- Provide automatic 3:2 and 2:2 pulldown detection
- Provide video input connections
- Video Output Requirements
- Provide one (1) HDMI for loop-through without video scaling, selectable for any video input.
- Provide scaled video output connections
- One (1) HDMI
- One (1) RJ-45 for DTP2 twisted pair
- Provide a range of selectable video output rates from 640x480 to 4096x2160 @ 60 Hz
- Support custom user-defined output resolutions via EDID management
- Provide image scaling and video format conversion with 30-bit precision and 4:4:4 chroma sampling
- Provide motion adaptive deinterlacing for signals up to 1080i
- Provide aspect ratio control
- When in FILL mode, the video image shall always fill the output screen without letterbox or pillarbox
- When in FOLLOW mode, the video image on the output screen shall always preserve the aspect ratio of the input signals without distortion
- Provide internal test patterns for calibration and setup
- Support image freeze via Ethernet, RS-232 or USB connection
- Support upload and placement of a custom logo graphic at any position on the video output
- Support logo placement as a foreground image
- Shall support uploading logo graphics in BMP, JPG, PNG, GIF, or TIFF format
- Shall support displaying full screen images up to 4096x2160 resolution
- Shall support up to 16 logo presets
- Shall support keying with selectable effects including transparency, color key, level key, and alpha key
- Support automatic muting of video and sync output when no video input signal is present
- Provide a choice to generate a blue screen or a black screen before disabling sync
- Provide a configurable timeout period before disabling sync
- The user may selectively enable or disable automatic muting of sync output
- Provide a low power standby state selectable via Ethernet, RS-232 or USB
- Support the connection of DVI displays that do not recognize HDMI-specific formats
- Automatically enable or disable embedded TMDS audio and InfoFrames
- Automatically set the correct color space
- Support selection of output color space as RGB or component video
- Switching Requirements
- Provide configurable automatic switching modes between input sources
- Last connected: always switch to the last active connected input
- Configurable priority: switching priority may be assigned arbitrarily for any combination of the four inputs
- Provide selectable transition effects when switching inputs
- Seamless Cut: video output shall freeze, then cut to the newly selected input source
- Seamless Fade: video output shall freeze, then fade into the newly selected input source
- Cut through black: video output shall cut to black, then cut to the newly selected input source
- Fade through black: video output shall fade to black, then fade into the newly selected input source
- Accompanying audio shall ramp down, then ramp up to match the transition effect
- Provide configurable automatic switching modes between input sources
- EDID Requirements
- Provide automatic EDID management between connected devices
- Provide a set of pre-stored EDID files
- Support capture of EDID from any connected display
- Support user uploading of custom-generated EDID files
- Support assignment of any pre-stored, captured, or custom uploaded EDID file to any input connection
- Provide automatic EDID management between connected devices
- HDCP Requirements
- The unit shall be HDCP 2.2 compliant
- Provide authentication and maintain continuous verification of HDCP key exchange with connected sink devices
- Provide authentication and maintain continuous verification of HDCP key exchange with connected source devices
- Provide the option to disable HDCP processing at video inputs 2 through 8 when passing unencrypted content
- Provide selectable, human-readable visual confirmation of HDCP compliance when encrypted content is routed to a non-HDCP compliant display
- When enabled, the video output shall be a solid green color and an on-screen message stating “HDCP CONTENT” shall be displayed
- When enabled, the option shall be provided to display a user-provided image in place of the green video output
- When disabled, the output shall be muted
- Provide real-time verification of HDCP status for each video input and output
- Directly readable on front panel LEDs
- Electronically accessible over Ethernet, RS-232 or USB connection
- The unit shall be HDCP 2.2 compliant
- DTP2 Twisted pair requirements
- Provide signal transmission distance capability of 330 feet (100 meters) for all supported video resolutions using a shielded CATx cable
- Support video, audio, RS-232, IR, and power transmission over a single shielded CATx cable
- Shall be compatible with CATx shielded twisted pair cable, and Extron XTP DTP 24 shielded twisted pair cable
- Support computer and video resolutions up to 3840x2160/60 at 4:4:4 chroma sampling
- Support stereo audio pass-through signals
- Shall actively buffer DDC channels
- Shall be configurable for compatibility with
- Extron DTP inputs
- Extron DTP2 inputs
- Extron XTP matrix switcher inputs
- HDBaseT inputs
- Provide power to remote DTP or DTP2 endpoint connected over the shielded CATx cable.
- Audio Requirements
- Provide audio input connections
- One (1) DisplayPort, embedded
- Five (5) HDMI, embedded
- Two (2) 5-pole 3.5 mm captive screw, balanced/unbalanced line level analog stereo
- Two (2) 3-pole 3.5 mm captive screw, balanced/unbalanced mic/line level with +48 volt phantom power
- Provide audio output connections
- One (1) 2-pole, 5 mm captive screw, mono speaker level connector
- Two (2) 5-pole 3.5 mm captive screw, with output level control and configurable for balanced/unbalanced, analog stereo or dual mono
- One (1) HDMI, embedded and with output level control for two-channel PCM
- One (1) RJ-45 for DTP2 twisted pair transmitting both:
- Embedded digital audio
- Pass-through stereo audio
- Provide mono amplification for high impedance speaker systems
- Support one mono speaker level signal on one 2-pole, 5 mm screw-lock captive screw connector
- Provide a total of 100 watts rms output power into a 70 volt load, measured at 1 kHz with 0.1% THD
- Provide a THD+N measurement of less than 0.1 % measured at 3 dB below clipping
- Provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Utilize an efficient Class D amplifier design
- Provide Class D Ripple Suppression technology
- Provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain with a slow attack and fast release to eliminate clipping distortion
- Provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults
- Support embedding of the analog audio input signal on the HDMI and DTP2 outputs
- Support extraction of two-channel PCM embedded audio signals to analog audio outputs, or pass bitstream audio to the HDMI and DTP2 outputs
- Provide the capability for all video inputs to share a common analog audio input
- Provide a delay in the audio output to match the corresponding video processing delay
- Provide gain and attenuation adjustments for analog input audio
- Support individual muting of the analog stereo or embedded digital audio outputs
- DSP Requirements
- Provide digital audio processing tools including gain, mixing, parametric EQ, filtering, dynamics, and ducking
- Provide adjustable, automatic ducking of program audio when a signal is detected on microphone inputs
- Provide DSP configuration and parameter adjustments through the product configuration software
- Provide real-time level meters for inputs and outputs in the product configuration software
- Provide live DSP parameter adjustments while they are heard or metered in real-time
- Provide user presets for saving and recalling DSP parameters
- Support storage and playback of up to 16 audio files at any audio output.
- Provide audio input connections
- Integrated Control Processor Requirements
- Provide AV system control connections
- Three RJ-45: 10/100/1000Base-T Ethernet, half/full duplex with auto-detect for connection to a LAN and include link and activity LED indicators located on the left and right of each jack for troubleshooting network issues, these ports will be designated as AV LAN ports allowing for AV devices to be isolated from a corporate network.
- AV LAN ports shall support a DHCP server that can distribute 50 dynamic IP addresses with a 24-hour lease
- One RJ-45: 10/100/1000Base-T, half/full duplex with auto-detect for connection to a LAN or WAN and includes link and activity LED indicators located on the left and right of the jack for troubleshooting network issues.
- Two 3-pole 3.5 mm captive screw: RS-232, configurable for unidirectional or bidirectional control of AV system components
- One 5-pole 3.5 mm captive screw: RS-232/RS-422/RS-485, configurable for unidirectional or bidirectional control of AV system components
- Two IR/serial ports on one 5-pole 3.5 mm captive screw: IR (using an IR emitter) or unidirectional RS-232 for control of AV system components
- Four low voltage relays on one 6-pole 3.5 mm captive screw: configurable for controlling lighting, controlling screens, or other device functions
- Four digital input/output ports on one 5-pole 3.5 mm captive screw: configurable for use as an interface with devices such as sensors, switches, LEDs, and relays
- One eBUS® port on a 4-pole 3.5 mm captive screw for connecting to eBUS devices
- Shall support the following protocols: ICMP (ping), IEEE 802.1X, IPv4, TCP, UDP, DHCP, DNS, HTTP, HTTPS, NTP, SFTP, SMTP, SNMP, SSH
- Shall support a Web-based AV resource management application that provides a means to manage, monitor, and control AV equipment
- Provide an internal real-time clock with a 30-year backup battery that is used to keep track of the date and time
- Shall support the addition of an Extron LinkLicense® for use of third party devices as primary control interfaces
- Provide front panel LED activity indicators for RS-232 status, RS-232/RS-422/RS-485 status, IR/serial status, digital I/O status, relay status, eBUS status, and network status
- Shall support control system synchronization to allow users to retain and recover configured endpoints in case of network or power failure
- Shall be configured using Extron Global Configurator® Plus or Extron Global Configurator Professional with support for the following:
- Provide support for up to eight configurable Extron TouchLink Pro touchpanels
- Provide support for up to eight configurable eBUS button panels
- Provide remote monitoring and control via Ethernet
- Provide the ability to create E-mail notifications
- Provide multiple levels of password protection
- Provide the ability to create schedules and monitors
- Support up to 32 Ethernet-controllable AV devices
- Support local variables and conditional logic
- Support grouping of multiple Extron IP Link® Pro xi control processors to function as one when configured with Global Configurator Professional
- Security Requirements
- Support SFTP and SSH for secure communication between the control processor and a TouchLink Pro touchpanel or Network Button Panel
- Support HTTPS and SSH for secure communication between the control processor and Extron Control App
- Support HTTPS for secure communication between the control processor and Extron Control for Web
- Support SSH for secure communication between the control processor and controlled device for programmed systems
- Support SFTP and SSH for secure communication between the control processor and the configuration or programming software
- Provide the option to modify administrator and user credentials
- Support security updates to maintain network health
- Require that a Secure Socket Layer (SSL) Certificate is installed to maintain system confidentiality and data integrity
- Support the installation of an owner furnished certificate with the following properties:
- Certificates shall include x.509 support
- Certificates shall include public / private key exchange
- Certificates shall support PEM encoding
- Extron shall furnish documentation that describes all supported network ports and services
- Provide AV system control connections
- Control/remote - RS-232 and IR Pass-Through Over Shielded CATx Requirements
- Provide connections for AV device control
- One (1) 3-pole 3.5 mm captive screw: IR pass-through to a DTP twisted pair receiver
- Support Ethernet insertion of RS-232 signals for transmission to a DTP endpoint
- Support RS-232 and IR transmission over shielded CATx up to 330 feet (100 meters)
- Provide connections for AV device control
- Control/remote – Presentation Switcher Requirements
- Provide control connections
- One (1) RJ-45: 10/100/1000Base-T Ethernet
- One (1) 3-pole 3.5 mm captive screw: RS-232
- One (1) Mini USB-B: USB 2.0
- Provide alternatives for configuration and operation
- On-screen menus navigated using front panel controls
- Product configuration software connected via Ethernet, USB, or RS-232
- Serial commands sent over Ethernet, RS-232 or USB connection
- Support disabling of front panel controls to prevent inadvertent or unauthorized changes to configuration settings
- Support triggering of standard CEC commands at main HDMI and DTP2 outputs
- Provide control connections
- General Requirements
- Enclosure shall be rack-mountable, full rack width, and 1RU in height
- Shall be equipped with an internal 100-240 VAC, 50/60 Hz universal power supply
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Video Input Requirements
- Approved device shall be the Extron IN1808 IPCP Q MA 70 (part number 60-1615-93); no alternates or equals
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
IN1808 IPCP Q MA 70
- Provide a video scaling presentation switcher that shall support up to eight inputs and two simultaneous outputs for processing and switching of DisplayPort and HDMI video sources, with additional support for signal extension over shielded CATx cable
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
- Video Input Requirements
- Provide video input connections
- One (1) DisplayPort supporting DisplayPort SST - Single Stream Transport data rates up to 21.6 Gbps
- Five (5) HDMI supporting HDMI specifications including 4K/60 Deep Color, data rates up to 18 Gbps, and HD lossless audio formats
- Two (2) RJ-45 for DTP2 twisted pair
- Provide automatic detection of input video parameters
- Determine total pixels, active pixels, active lines, H/V starting points, H/V image positions, H/V image sizes, and video clock phase
- The user may selectively enable to disable automatic detection for each input
- Provide image adjustments for brightness, contrast, color, tint, detail, H/V positioning, and sizing
- Provide storage and recall of video parameters and picture settings
- Automatic memories for each video input
- Save video settings and picture adjustments without user intervention
- Automatically recall settings when the same video rate is encountered
- The user may selectively enable or disable automatic memories
- Manual user presets
- Save picture adjustments
- User presets may be saved and recalled using front panel controls
- User presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Manual input presets
- Save video settings and picture adjustments
- Input presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Automatic memories for each video input
- Provide automatic 3:2 and 2:2 pulldown detection
- Provide video input connections
- Video Output Requirements
- Provide one (1) HDMI for loop-through without video scaling, selectable for any video input.
- Provide scaled video output connections
- One (1) HDMI
- One (1) RJ-45 for DTP2 twisted pair
- Provide a range of selectable video output rates from 640x480 to 4096x2160 @ 60 Hz
- Support custom user-defined output resolutions via EDID management
- Provide image scaling and video format conversion with 30-bit precision and 4:4:4 chroma sampling
- Provide motion adaptive deinterlacing for signals up to 1080i
- Provide aspect ratio control
- When in FILL mode, the video image shall always fill the output screen without letterbox or pillarbox
- When in FOLLOW mode, the video image on the output screen shall always preserve the aspect ratio of the input signals without distortion
- Provide internal test patterns for calibration and setup
- Support image freeze via Ethernet, RS-232 or USB connection
- Support upload and placement of a custom logo graphic at any position on the video output
- Support logo placement as a foreground image
- Shall support uploading logo graphics in BMP, JPG, PNG, GIF, or TIFF format
- Shall support displaying full screen images up to 4096x2160 resolution
- Shall support up to 16 logo presets
- Shall support keying with selectable effects including transparency, color key, level key, and alpha key
- Support automatic muting of video and sync output when no video input signal is present
- Provide a choice to generate a blue screen or a black screen before disabling sync
- Provide a configurable timeout period before disabling sync
- The user may selectively enable or disable automatic muting of sync output
- Provide a low power standby state selectable via Ethernet, RS-232 or USB
- Support the connection of DVI displays that do not recognize HDMI-specific formats
- Automatically enable or disable embedded TMDS audio and InfoFrames
- Automatically set the correct color space
- Support selection of output color space as RGB or component video
- Switching Requirements
- Provide configurable automatic switching modes between input sources
- Last connected: always switch to the last active connected input
- Configurable priority: switching priority may be assigned arbitrarily for any combination of the four inputs
- Provide selectable transition effects when switching inputs
- Seamless Cut: video output shall freeze, then cut to the newly selected input source
- Seamless Fade: video output shall freeze, then fade into the newly selected input source
- Cut through black: video output shall cut to black, then cut to the newly selected input source
- Fade through black: video output shall fade to black, then fade into the newly selected input source
- Accompanying audio shall ramp down, then ramp up to match the transition effect
- Provide configurable automatic switching modes between input sources
- EDID Requirements
- Provide automatic EDID management between connected devices
- Provide a set of pre-stored EDID files
- Support capture of EDID from any connected display
- Support user uploading of custom-generated EDID files
- Support assignment of any pre-stored, captured, or custom uploaded EDID file to any input connection
- Provide automatic EDID management between connected devices
- HDCP Requirements
- The unit shall be HDCP 2.2 compliant
- Provide authentication and maintain continuous verification of HDCP key exchange with connected sink devices
- Provide authentication and maintain continuous verification of HDCP key exchange with connected source devices
- Provide the option to disable HDCP processing at video inputs 2 through 8 when passing unencrypted content
- Provide selectable, human-readable visual confirmation of HDCP compliance when encrypted content is routed to a non-HDCP compliant display
- When enabled, the video output shall be a solid green color and an on-screen message stating “HDCP CONTENT” shall be displayed
- When enabled, the option shall be provided to display a user-provided image in place of the green video output
- When disabled, the output shall be muted
- Provide real-time verification of HDCP status for each video input and output
- Directly readable on front panel LEDs
- Electronically accessible over Ethernet, RS-232 or USB connection
- The unit shall be HDCP 2.2 compliant
- DTP2 Twisted pair requirements
- Provide signal transmission distance capability of 330 feet (100 meters) for all supported video resolutions using a shielded CATx cable
- Support video, audio, RS-232, IR, and power transmission over a single shielded CATx cable
- Shall be compatible with CATx shielded twisted pair cable, and Extron XTP DTP 24 shielded twisted pair cable
- Support computer and video resolutions up to 3840x2160/60 at 4:4:4 chroma sampling
- Support stereo audio pass-through signals
- Shall actively buffer DDC channels
- Shall be configurable for compatibility with
- Extron DTP inputs
- Extron DTP2 inputs
- Extron XTP matrix switcher inputs
- HDBaseT inputs
- Provide power to remote DTP or DTP2 endpoint connected over the shielded CATx cable.
- Audio Requirements
- Provide audio input connections
- One (1) DisplayPort, embedded
- Five (5) HDMI, embedded
- Two (2) 5-pole 3.5 mm captive screw, balanced/unbalanced line level analog stereo
- Two (2) 3-pole 3.5 mm captive screw, balanced/unbalanced mic/line level with +48 volt phantom power
- Provide audio output connections
- One (1) 2-pole, 5 mm captive screw, mono speaker level connector
- Two (2) 5-pole 3.5 mm captive screw, with output level control and configurable for balanced/unbalanced, analog stereo or dual mono
- One (1) HDMI, embedded and with output level control for two-channel PCM
- One (1) RJ-45 for DTP2 twisted pair transmitting both:
- Embedded digital audio
- Pass-through stereo audio
- Provide mono amplification for high impedance speaker systems
- Support one mono speaker level signal on one 2-pole, 5 mm screw-lock captive screw connector
- Provide a total of 100 watts rms output power into a 70 volt load, measured at 1 kHz with 0.1% THD
- Provide a THD+N measurement of less than 0.1 % measured at 3 dB below clipping
- Provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Utilize an efficient Class D amplifier design
- Provide Class D Ripple Suppression technology
- Provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain with a slow attack and fast release to eliminate clipping distortion
- Provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults
- Support embedding of the analog audio input signal on the HDMI and DTP2 outputs
- Support extraction of two-channel PCM embedded audio signals to analog audio outputs, or pass bitstream audio to the HDMI and DTP2 outputs
- Provide the capability for all video inputs to share a common analog audio input
- Provide a delay in the audio output to match the corresponding video processing delay
- Provide gain and attenuation adjustments for analog input audio
- Support individual muting of the analog stereo or embedded digital audio outputs
- DSP Requirements
- Provide digital audio processing tools including gain, mixing, parametric EQ, filtering, dynamics, and ducking
- Provide adjustable, automatic ducking of program audio when a signal is detected on microphone inputs
- Provide DSP configuration and parameter adjustments through the product configuration software
- Provide real-time level meters for inputs and outputs in the product configuration software
- Provide live DSP parameter adjustments while they are heard or metered in real-time
- Provide user presets for saving and recalling DSP parameters
- Support storage and playback of up to 16 audio files at any audio output.
- Provide audio input connections
- Integrated Control Processor Requirements
- Provide AV system control connections
- Three RJ-45: 10/100/1000Base-T Ethernet, half/full duplex with auto-detect for connection to a LAN and include link and activity LED indicators located on the left and right of each jack for troubleshooting network issues, these ports will be designated as AV LAN ports allowing for AV devices to be isolated from a corporate network.
- AV LAN ports shall support a DHCP server that can distribute 50 dynamic IP addresses with a 24-hour lease
- One RJ-45: 10/100/1000Base-T, half/full duplex with auto-detect for connection to a LAN or WAN and includes link and activity LED indicators located on the left and right of the jack for troubleshooting network issues.
- Two 3-pole 3.5 mm captive screw: RS-232, configurable for unidirectional or bidirectional control of AV system components
- One 5-pole 3.5 mm captive screw: RS-232/RS-422/RS-485, configurable for unidirectional or bidirectional control of AV system components
- Two IR/serial ports on one 5-pole 3.5 mm captive screw: IR (using an IR emitter) or unidirectional RS-232 for control of AV system components
- Four low voltage relays on one 6-pole 3.5 mm captive screw: configurable for controlling lighting, controlling screens, or other device functions
- Four digital input/output ports on one 5-pole 3.5 mm captive screw: configurable for use as an interface with devices such as sensors, switches, LEDs, and relays
- One eBUS® port on a 4-pole 3.5 mm captive screw for connecting to eBUS devices
- Shall support the following protocols: ICMP (ping), IEEE 802.1X, IPv4, TCP, UDP, DHCP, DNS, HTTP, HTTPS, NTP, SFTP, SMTP, SNMP, SSH
- Shall support a Web-based AV resource management application that provides a means to manage, monitor, and control AV equipment
- Provide an internal real-time clock with a 30-year backup battery that is used to keep track of the date and time
- Shall support the addition of an Extron LinkLicense® for use of third party devices as primary control interfaces
- Provide front panel LED activity indicators for RS-232 status, RS-232/RS-422/RS-485 status, IR/serial status, digital I/O status, relay status, eBUS status, and network status
- Shall support control system synchronization to allow users to retain and recover configured endpoints in case of network or power failure
- Shall be configured using Extron Global Configurator® Plus or Extron Global Configurator Professional with support for the following:
- Provide support for up to eight configurable Extron TouchLink Pro touchpanels
- Provide support for up to eight configurable eBUS button panels
- Provide remote monitoring and control via Ethernet
- Provide the ability to create E-mail notifications
- Provide multiple levels of password protection
- Provide the ability to create schedules and monitors
- Support up to 32 Ethernet-controllable AV devices
- Support local variables and conditional logic
- Support grouping of multiple Extron IP Link® Pro xi control processors to function as one when configured with Global Configurator Professional
- Security Requirements
- Support SFTP and SSH for secure communication between the control processor and a TouchLink Pro touchpanel or Network Button Panel
- Support HTTPS and SSH for secure communication between the control processor and Extron Control App
- Support HTTPS for secure communication between the control processor and Extron Control for Web
- Support SSH for secure communication between the control processor and controlled device for programmed systems
- Support SFTP and SSH for secure communication between the control processor and the configuration or programming software
- Provide the option to modify administrator and user credentials
- Support security updates to maintain network health
- Require that a Secure Socket Layer (SSL) Certificate is installed to maintain system confidentiality and data integrity
- Support the installation of an owner furnished certificate with the following properties:
- Certificates shall include x.509 support
- Certificates shall include public / private key exchange
- Certificates shall support PEM encoding
- Extron shall furnish documentation that describes all supported network ports and services
- Provide AV system control connections
- Control/remote - RS-232 and IR Pass-Through Over Shielded CATx Requirements
- Provide connections for AV device control
- One (1) 3-pole 3.5 mm captive screw: IR pass-through to a DTP twisted pair receiver
- Support Ethernet insertion of RS-232 signals for transmission to a DTP endpoint
- Support RS-232 and IR transmission over shielded CATx up to 330 feet (100 meters)
- Provide connections for AV device control
- Control/remote – Presentation Switcher Requirements
- Provide control connections
- One (1) RJ-45: 10/100/1000Base-T Ethernet
- One (1) 3-pole 3.5 mm captive screw: RS-232
- One (1) Mini USB-B: USB 2.0
- Provide alternatives for configuration and operation
- On-screen menus navigated using front panel controls
- Product configuration software connected via Ethernet, USB, or RS-232
- Serial commands sent over Ethernet, RS-232 or USB connection
- Support disabling of front panel controls to prevent inadvertent or unauthorized changes to configuration settings
- Support triggering of standard CEC commands at main HDMI and DTP2 outputs
- Provide control connections
- General Requirements
- Enclosure shall be rack-mountable, full rack width, and 1RU in height
- Shall be equipped with an internal 100-240 VAC, 50/60 Hz universal power supply
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Video Input Requirements
- Approved device shall be the Extron IN1808 IPCP Q MA 70 (part number 60-1615-93); no alternates or equals
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
IN1808 IPCP Q MA 70
- Provide a video scaling presentation switcher that shall support up to eight inputs and two simultaneous outputs for processing and switching of DisplayPort and HDMI video sources, with additional support for signal extension over shielded CATx cable
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
- Video Input Requirements
- Provide video input connections
- One (1) DisplayPort supporting DisplayPort SST - Single Stream Transport data rates up to 21.6 Gbps
- Five (5) HDMI supporting HDMI specifications including 4K/60 Deep Color, data rates up to 18 Gbps, and HD lossless audio formats
- Two (2) RJ-45 for DTP2 twisted pair
- Provide automatic detection of input video parameters
- Determine total pixels, active pixels, active lines, H/V starting points, H/V image positions, H/V image sizes, and video clock phase
- The user may selectively enable to disable automatic detection for each input
- Provide image adjustments for brightness, contrast, color, tint, detail, H/V positioning, and sizing
- Provide storage and recall of video parameters and picture settings
- Automatic memories for each video input
- Save video settings and picture adjustments without user intervention
- Automatically recall settings when the same video rate is encountered
- The user may selectively enable or disable automatic memories
- Manual user presets
- Save picture adjustments
- User presets may be saved and recalled using front panel controls
- User presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Manual input presets
- Save video settings and picture adjustments
- Input presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Automatic memories for each video input
- Provide automatic 3:2 and 2:2 pulldown detection
- Provide video input connections
- Video Output Requirements
- Provide one (1) HDMI for loop-through without video scaling, selectable for any video input.
- Provide scaled video output connections
- One (1) HDMI
- One (1) RJ-45 for DTP2 twisted pair
- Provide a range of selectable video output rates from 640x480 to 4096x2160 @ 60 Hz
- Support custom user-defined output resolutions via EDID management
- Provide image scaling and video format conversion with 30-bit precision and 4:4:4 chroma sampling
- Provide motion adaptive deinterlacing for signals up to 1080i
- Provide aspect ratio control
- When in FILL mode, the video image shall always fill the output screen without letterbox or pillarbox
- When in FOLLOW mode, the video image on the output screen shall always preserve the aspect ratio of the input signals without distortion
- Provide internal test patterns for calibration and setup
- Support image freeze via Ethernet, RS-232 or USB connection
- Support upload and placement of a custom logo graphic at any position on the video output
- Support logo placement as a foreground image
- Shall support uploading logo graphics in BMP, JPG, PNG, GIF, or TIFF format
- Shall support displaying full screen images up to 4096x2160 resolution
- Shall support up to 16 logo presets
- Shall support keying with selectable effects including transparency, color key, level key, and alpha key
- Support automatic muting of video and sync output when no video input signal is present
- Provide a choice to generate a blue screen or a black screen before disabling sync
- Provide a configurable timeout period before disabling sync
- The user may selectively enable or disable automatic muting of sync output
- Provide a low power standby state selectable via Ethernet, RS-232 or USB
- Support the connection of DVI displays that do not recognize HDMI-specific formats
- Automatically enable or disable embedded TMDS audio and InfoFrames
- Automatically set the correct color space
- Support selection of output color space as RGB or component video
- Switching Requirements
- Provide configurable automatic switching modes between input sources
- Last connected: always switch to the last active connected input
- Configurable priority: switching priority may be assigned arbitrarily for any combination of the four inputs
- Provide selectable transition effects when switching inputs
- Seamless Cut: video output shall freeze, then cut to the newly selected input source
- Seamless Fade: video output shall freeze, then fade into the newly selected input source
- Cut through black: video output shall cut to black, then cut to the newly selected input source
- Fade through black: video output shall fade to black, then fade into the newly selected input source
- Accompanying audio shall ramp down, then ramp up to match the transition effect
- Provide configurable automatic switching modes between input sources
- EDID Requirements
- Provide automatic EDID management between connected devices
- Provide a set of pre-stored EDID files
- Support capture of EDID from any connected display
- Support user uploading of custom-generated EDID files
- Support assignment of any pre-stored, captured, or custom uploaded EDID file to any input connection
- Provide automatic EDID management between connected devices
- HDCP Requirements
- The unit shall be HDCP 2.2 compliant
- Provide authentication and maintain continuous verification of HDCP key exchange with connected sink devices
- Provide authentication and maintain continuous verification of HDCP key exchange with connected source devices
- Provide the option to disable HDCP processing at video inputs 2 through 8 when passing unencrypted content
- Provide selectable, human-readable visual confirmation of HDCP compliance when encrypted content is routed to a non-HDCP compliant display
- When enabled, the video output shall be a solid green color and an on-screen message stating “HDCP CONTENT” shall be displayed
- When enabled, the option shall be provided to display a user-provided image in place of the green video output
- When disabled, the output shall be muted
- Provide real-time verification of HDCP status for each video input and output
- Directly readable on front panel LEDs
- Electronically accessible over Ethernet, RS-232 or USB connection
- The unit shall be HDCP 2.2 compliant
- DTP2 Twisted pair requirements
- Provide signal transmission distance capability of 330 feet (100 meters) for all supported video resolutions using a shielded CATx cable
- Support video, audio, RS-232, IR, and power transmission over a single shielded CATx cable
- Shall be compatible with CATx shielded twisted pair cable, and Extron XTP DTP 24 shielded twisted pair cable
- Support computer and video resolutions up to 3840x2160/60 at 4:4:4 chroma sampling
- Support stereo audio pass-through signals
- Shall actively buffer DDC channels
- Shall be configurable for compatibility with
- Extron DTP inputs
- Extron DTP2 inputs
- Extron XTP matrix switcher inputs
- HDBaseT inputs
- Provide power to remote DTP or DTP2 endpoint connected over the shielded CATx cable.
- Audio Requirements
- Provide audio input connections
- One (1) DisplayPort, embedded
- Five (5) HDMI, embedded
- Two (2) 5-pole 3.5 mm captive screw, balanced/unbalanced line level analog stereo
- Two (2) 3-pole 3.5 mm captive screw, balanced/unbalanced mic/line level with +48 volt phantom power
- Provide audio output connections
- One (1) 2-pole, 5 mm captive screw, mono speaker level connector
- Two (2) 5-pole 3.5 mm captive screw, with output level control and configurable for balanced/unbalanced, analog stereo or dual mono
- One (1) HDMI, embedded and with output level control for two-channel PCM
- One (1) RJ-45 for DTP2 twisted pair transmitting both:
- Embedded digital audio
- Pass-through stereo audio
- Provide mono amplification for high impedance speaker systems
- Support one mono speaker level signal on one 2-pole, 5 mm screw-lock captive screw connector
- Provide a total of 100 watts rms output power into a 70 volt load, measured at 1 kHz with 0.1% THD
- Provide a THD+N measurement of less than 0.1 % measured at 3 dB below clipping
- Provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Utilize an efficient Class D amplifier design
- Provide Class D Ripple Suppression technology
- Provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain with a slow attack and fast release to eliminate clipping distortion
- Provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults
- Support embedding of the analog audio input signal on the HDMI and DTP2 outputs
- Support extraction of two-channel PCM embedded audio signals to analog audio outputs, or pass bitstream audio to the HDMI and DTP2 outputs
- Provide the capability for all video inputs to share a common analog audio input
- Provide a delay in the audio output to match the corresponding video processing delay
- Provide gain and attenuation adjustments for analog input audio
- Support individual muting of the analog stereo or embedded digital audio outputs
- DSP Requirements
- Provide digital audio processing tools including gain, mixing, parametric EQ, filtering, dynamics, and ducking
- Provide adjustable, automatic ducking of program audio when a signal is detected on microphone inputs
- Provide DSP configuration and parameter adjustments through the product configuration software
- Provide real-time level meters for inputs and outputs in the product configuration software
- Provide live DSP parameter adjustments while they are heard or metered in real-time
- Provide user presets for saving and recalling DSP parameters
- Support storage and playback of up to 16 audio files at any audio output.
- Provide audio input connections
- Integrated Control Processor Requirements
- Provide AV system control connections
- Three RJ-45: 10/100/1000Base-T Ethernet, half/full duplex with auto-detect for connection to a LAN and include link and activity LED indicators located on the left and right of each jack for troubleshooting network issues, these ports will be designated as AV LAN ports allowing for AV devices to be isolated from a corporate network.
- AV LAN ports shall support a DHCP server that can distribute 50 dynamic IP addresses with a 24-hour lease
- One RJ-45: 10/100/1000Base-T, half/full duplex with auto-detect for connection to a LAN or WAN and includes link and activity LED indicators located on the left and right of the jack for troubleshooting network issues.
- Two 3-pole 3.5 mm captive screw: RS-232, configurable for unidirectional or bidirectional control of AV system components
- One 5-pole 3.5 mm captive screw: RS-232/RS-422/RS-485, configurable for unidirectional or bidirectional control of AV system components
- Two IR/serial ports on one 5-pole 3.5 mm captive screw: IR (using an IR emitter) or unidirectional RS-232 for control of AV system components
- Four low voltage relays on one 6-pole 3.5 mm captive screw: configurable for controlling lighting, controlling screens, or other device functions
- Four digital input/output ports on one 5-pole 3.5 mm captive screw: configurable for use as an interface with devices such as sensors, switches, LEDs, and relays
- One eBUS® port on a 4-pole 3.5 mm captive screw for connecting to eBUS devices
- Shall support the following protocols: ICMP (ping), IEEE 802.1X, IPv4, TCP, UDP, DHCP, DNS, HTTP, HTTPS, NTP, SFTP, SMTP, SNMP, SSH
- Shall support a Web-based AV resource management application that provides a means to manage, monitor, and control AV equipment
- Provide an internal real-time clock with a 30-year backup battery that is used to keep track of the date and time
- Shall include an Extron LinkLicense® for use of third party devices as primary control interfaces
- Provide front panel LED activity indicators for RS-232 status, RS-232/RS-422/RS-485 status, IR/serial status, digital I/O status, relay status, eBUS status, and network status
- Shall support control system synchronization to allow users to retain and recover configured endpoints in case of network or power failure
- Shall be configured using Extron Global Configurator® Plus or Extron Global Configurator Professional with support for the following:
- Provide support for up to eight configurable Extron TouchLink Pro touchpanels
- Provide support for up to eight configurable eBUS button panels
- Provide remote monitoring and control via Ethernet
- Provide the ability to create E-mail notifications
- Provide multiple levels of password protection
- Provide the ability to create schedules and monitors
- Support up to 32 Ethernet-controllable AV devices
- Support local variables and conditional logic
- Support grouping of multiple Extron IP Link® Pro xi control processors to function as one when configured with Global Configurator Professional
- Security Requirements
- Support SFTP and SSH for secure communication between the control processor and a TouchLink Pro touchpanel or Network Button Panel
- Support HTTPS and SSH for secure communication between the control processor and Extron Control App
- Support HTTPS for secure communication between the control processor and Extron Control for Web
- Support SSH for secure communication between the control processor and controlled device for programmed systems
- Support SFTP and SSH for secure communication between the control processor and the configuration or programming software
- Provide the option to modify administrator and user credentials
- Support security updates to maintain network health
- Require that a Secure Socket Layer (SSL) Certificate is installed to maintain system confidentiality and data integrity
- Support the installation of an owner furnished certificate with the following properties:
- Certificates shall include x.509 support
- Certificates shall include public / private key exchange
- Certificates shall support PEM encoding
- Extron shall furnish documentation that describes all supported network ports and services
- Provide AV system control connections
- Control/remote - RS-232 and IR Pass-Through Over Shielded CATx Requirements
- Provide connections for AV device control
- One (1) 3-pole 3.5 mm captive screw: IR pass-through to a DTP twisted pair receiver
- Support Ethernet insertion of RS-232 signals for transmission to a DTP endpoint
- Support RS-232 and IR transmission over shielded CATx up to 330 feet (100 meters)
- Provide connections for AV device control
- Control/remote – Presentation Switcher Requirements
- Provide control connections
- One (1) RJ-45: 10/100/1000Base-T Ethernet
- One (1) 3-pole 3.5 mm captive screw: RS-232
- One (1) Mini USB-B: USB 2.0
- Provide alternatives for configuration and operation
- On-screen menus navigated using front panel controls
- Product configuration software connected via Ethernet, USB, or RS-232
- Serial commands sent over Ethernet, RS-232 or USB connection
- Support disabling of front panel controls to prevent inadvertent or unauthorized changes to configuration settings
- Support triggering of standard CEC commands at main HDMI and DTP2 outputs
- Provide control connections
- General Requirements
- Enclosure shall be rack-mountable, full rack width, and 1RU in height
- Shall be equipped with an internal 100-240 VAC, 50/60 Hz universal power supply
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Video Input Requirements
- Approved device shall be the Extron IN1808 IPCP Q MA 70 (part number 60-1615-93A); no alternates or equals
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
IN1808 IPCP Q MA 70
- Provide a video scaling presentation switcher that shall support up to eight inputs and two simultaneous outputs for processing and switching of DisplayPort and HDMI video sources, with additional support for signal extension over shielded CATx cable
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
- Video Input Requirements
- Provide video input connections
- One (1) DisplayPort supporting DisplayPort SST - Single Stream Transport data rates up to 21.6 Gbps
- Five (5) HDMI supporting HDMI specifications including 4K/60 Deep Color, data rates up to 18 Gbps, and HD lossless audio formats
- Two (2) RJ-45 for DTP2 twisted pair
- Provide automatic detection of input video parameters
- Determine total pixels, active pixels, active lines, H/V starting points, H/V image positions, H/V image sizes, and video clock phase
- The user may selectively enable to disable automatic detection for each input
- Provide image adjustments for brightness, contrast, color, tint, detail, H/V positioning, and sizing
- Provide storage and recall of video parameters and picture settings
- Automatic memories for each video input
- Save video settings and picture adjustments without user intervention
- Automatically recall settings when the same video rate is encountered
- The user may selectively enable or disable automatic memories
- Manual user presets
- Save picture adjustments
- User presets may be saved and recalled using front panel controls
- User presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Manual input presets
- Save video settings and picture adjustments
- Input presets may be saved and recalled electronically via Ethernet, RS-232 or USB connection
- Automatic memories for each video input
- Provide automatic 3:2 and 2:2 pulldown detection
- Provide video input connections
- Video Output Requirements
- Provide one (1) HDMI for loop-through without video scaling, selectable for any video input.
- Provide scaled video output connections
- One (1) HDMI
- One (1) RJ-45 for DTP2 twisted pair
- Provide a range of selectable video output rates from 640x480 to 4096x2160 @ 60 Hz
- Support custom user-defined output resolutions via EDID management
- Provide image scaling and video format conversion with 30-bit precision and 4:4:4 chroma sampling
- Provide motion adaptive deinterlacing for signals up to 1080i
- Provide aspect ratio control
- When in FILL mode, the video image shall always fill the output screen without letterbox or pillarbox
- When in FOLLOW mode, the video image on the output screen shall always preserve the aspect ratio of the input signals without distortion
- Provide internal test patterns for calibration and setup
- Support image freeze via Ethernet, RS-232 or USB connection
- Support upload and placement of a custom logo graphic at any position on the video output
- Support logo placement as a foreground image
- Shall support uploading logo graphics in BMP, JPG, PNG, GIF, or TIFF format
- Shall support displaying full screen images up to 4096x2160 resolution
- Shall support up to 16 logo presets
- Shall support keying with selectable effects including transparency, color key, level key, and alpha key
- Support automatic muting of video and sync output when no video input signal is present
- Provide a choice to generate a blue screen or a black screen before disabling sync
- Provide a configurable timeout period before disabling sync
- The user may selectively enable or disable automatic muting of sync output
- Provide a low power standby state selectable via Ethernet, RS-232 or USB
- Support the connection of DVI displays that do not recognize HDMI-specific formats
- Automatically enable or disable embedded TMDS audio and InfoFrames
- Automatically set the correct color space
- Support selection of output color space as RGB or component video
- Switching Requirements
- Provide configurable automatic switching modes between input sources
- Last connected: always switch to the last active connected input
- Configurable priority: switching priority may be assigned arbitrarily for any combination of the four inputs
- Provide selectable transition effects when switching inputs
- Seamless Cut: video output shall freeze, then cut to the newly selected input source
- Seamless Fade: video output shall freeze, then fade into the newly selected input source
- Cut through black: video output shall cut to black, then cut to the newly selected input source
- Fade through black: video output shall fade to black, then fade into the newly selected input source
- Accompanying audio shall ramp down, then ramp up to match the transition effect
- Provide configurable automatic switching modes between input sources
- EDID Requirements
- Provide automatic EDID management between connected devices
- Provide a set of pre-stored EDID files
- Support capture of EDID from any connected display
- Support user uploading of custom-generated EDID files
- Support assignment of any pre-stored, captured, or custom uploaded EDID file to any input connection
- Provide automatic EDID management between connected devices
- HDCP Requirements
- The unit shall be HDCP 2.2 compliant
- Provide authentication and maintain continuous verification of HDCP key exchange with connected sink devices
- Provide authentication and maintain continuous verification of HDCP key exchange with connected source devices
- Provide the option to disable HDCP processing at video inputs 2 through 8 when passing unencrypted content
- Provide selectable, human-readable visual confirmation of HDCP compliance when encrypted content is routed to a non-HDCP compliant display
- When enabled, the video output shall be a solid green color and an on-screen message stating “HDCP CONTENT” shall be displayed
- When enabled, the option shall be provided to display a user-provided image in place of the green video output
- When disabled, the output shall be muted
- Provide real-time verification of HDCP status for each video input and output
- Directly readable on front panel LEDs
- Electronically accessible over Ethernet, RS-232 or USB connection
- The unit shall be HDCP 2.2 compliant
- DTP2 Twisted pair requirements
- Provide signal transmission distance capability of 330 feet (100 meters) for all supported video resolutions using a shielded CATx cable
- Support video, audio, RS-232, IR, and power transmission over a single shielded CATx cable
- Shall be compatible with CATx shielded twisted pair cable, and Extron XTP DTP 24 shielded twisted pair cable
- Support computer and video resolutions up to 3840x2160/60 at 4:4:4 chroma sampling
- Support stereo audio pass-through signals
- Shall actively buffer DDC channels
- Shall be configurable for compatibility with
- Extron DTP inputs
- Extron DTP2 inputs
- Extron XTP matrix switcher inputs
- HDBaseT inputs
- Provide power to remote DTP or DTP2 endpoint connected over the shielded CATx cable.
- Audio Requirements
- Provide audio input connections
- One (1) DisplayPort, embedded
- Five (5) HDMI, embedded
- Two (2) 5-pole 3.5 mm captive screw, balanced/unbalanced line level analog stereo
- Two (2) 3-pole 3.5 mm captive screw, balanced/unbalanced mic/line level with +48 volt phantom power
- Provide audio output connections
- One (1) 2-pole, 5 mm captive screw, mono speaker level connector
- Two (2) 5-pole 3.5 mm captive screw, with output level control and configurable for balanced/unbalanced, analog stereo or dual mono
- One (1) HDMI, embedded and with output level control for two-channel PCM
- One (1) RJ-45 for DTP2 twisted pair transmitting both:
- Embedded digital audio
- Pass-through stereo audio
- Provide mono amplification for high impedance speaker systems
- Support one mono speaker level signal on one 2-pole, 5 mm screw-lock captive screw connector
- Provide a total of 100 watts rms output power into a 70 volt load, measured at 1 kHz with 0.1% THD
- Provide a THD+N measurement of less than 0.1 % measured at 3 dB below clipping
- Provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Utilize an efficient Class D amplifier design
- Provide Class D Ripple Suppression technology
- Provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain with a slow attack and fast release to eliminate clipping distortion
- Provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults
- Support embedding of the analog audio input signal on the HDMI and DTP2 outputs
- Support extraction of two-channel PCM embedded audio signals to analog audio outputs, or pass bitstream audio to the HDMI and DTP2 outputs
- Provide the capability for all video inputs to share a common analog audio input
- Provide a delay in the audio output to match the corresponding video processing delay
- Provide gain and attenuation adjustments for analog input audio
- Support individual muting of the analog stereo or embedded digital audio outputs
- DSP Requirements
- Provide digital audio processing tools including gain, mixing, parametric EQ, filtering, dynamics, and ducking
- Provide adjustable, automatic ducking of program audio when a signal is detected on microphone inputs
- Provide DSP configuration and parameter adjustments through the product configuration software
- Provide real-time level meters for inputs and outputs in the product configuration software
- Provide live DSP parameter adjustments while they are heard or metered in real-time
- Provide user presets for saving and recalling DSP parameters
- Support storage and playback of up to 16 audio files at any audio output.
- Provide audio input connections
- Integrated Control Processor Requirements
- Provide AV system control connections
- Three RJ-45: 10/100/1000Base-T Ethernet, half/full duplex with auto-detect for connection to a LAN and include link and activity LED indicators located on the left and right of each jack for troubleshooting network issues, these ports will be designated as AV LAN ports allowing for AV devices to be isolated from a corporate network.
- AV LAN ports shall support a DHCP server that can distribute 50 dynamic IP addresses with a 24-hour lease
- One RJ-45: 10/100/1000Base-T, half/full duplex with auto-detect for connection to a LAN or WAN and includes link and activity LED indicators located on the left and right of the jack for troubleshooting network issues.
- Two 3-pole 3.5 mm captive screw: RS-232, configurable for unidirectional or bidirectional control of AV system components
- One 5-pole 3.5 mm captive screw: RS-232/RS-422/RS-485, configurable for unidirectional or bidirectional control of AV system components
- Two IR/serial ports on one 5-pole 3.5 mm captive screw: IR (using an IR emitter) or unidirectional RS-232 for control of AV system components
- Four low voltage relays on one 6-pole 3.5 mm captive screw: configurable for controlling lighting, controlling screens, or other device functions
- Four digital input/output ports on one 5-pole 3.5 mm captive screw: configurable for use as an interface with devices such as sensors, switches, LEDs, and relays
- One eBUS® port on a 4-pole 3.5 mm captive screw for connecting to eBUS devices
- Shall support the following protocols: ICMP (ping), IEEE 802.1X, IPv4, TCP, UDP, DHCP, DNS, HTTP, HTTPS, NTP, SFTP, SMTP, SNMP, SSH
- Shall support a Web-based AV resource management application that provides a means to manage, monitor, and control AV equipment
- Provide an internal real-time clock with a 30-year backup battery that is used to keep track of the date and time
- Shall include an Extron LinkLicense® for use of third party devices as primary control interfaces
- Provide front panel LED activity indicators for RS-232 status, RS-232/RS-422/RS-485 status, IR/serial status, digital I/O status, relay status, eBUS status, and network status
- Shall support control system synchronization to allow users to retain and recover configured endpoints in case of network or power failure
- Shall be configured using Extron Global Configurator® Plus or Extron Global Configurator Professional with support for the following:
- Provide support for up to eight configurable Extron TouchLink Pro touchpanels
- Provide support for up to eight configurable eBUS button panels
- Provide remote monitoring and control via Ethernet
- Provide the ability to create E-mail notifications
- Provide multiple levels of password protection
- Provide the ability to create schedules and monitors
- Support up to 32 Ethernet-controllable AV devices
- Support local variables and conditional logic
- Support grouping of multiple Extron IP Link® Pro xi control processors to function as one when configured with Global Configurator Professional
- Security Requirements
- Support SFTP and SSH for secure communication between the control processor and a TouchLink Pro touchpanel or Network Button Panel
- Support HTTPS and SSH for secure communication between the control processor and Extron Control App
- Support HTTPS for secure communication between the control processor and Extron Control for Web
- Support SSH for secure communication between the control processor and controlled device for programmed systems
- Support SFTP and SSH for secure communication between the control processor and the configuration or programming software
- Provide the option to modify administrator and user credentials
- Support security updates to maintain network health
- Require that a Secure Socket Layer (SSL) Certificate is installed to maintain system confidentiality and data integrity
- Support the installation of an owner furnished certificate with the following properties:
- Certificates shall include x.509 support
- Certificates shall include public / private key exchange
- Certificates shall support PEM encoding
- Extron shall furnish documentation that describes all supported network ports and services
- Provide AV system control connections
- Control/remote - RS-232 and IR Pass-Through Over Shielded CATx Requirements
- Provide connections for AV device control
- One (1) 3-pole 3.5 mm captive screw: IR pass-through to a DTP twisted pair receiver
- Support Ethernet insertion of RS-232 signals for transmission to a DTP endpoint
- Support RS-232 and IR transmission over shielded CATx up to 330 feet (100 meters)
- Provide connections for AV device control
- Control/remote – Presentation Switcher Requirements
- Provide control connections
- One (1) RJ-45: 10/100/1000Base-T Ethernet
- One (1) 3-pole 3.5 mm captive screw: RS-232
- One (1) Mini USB-B: USB 2.0
- Provide alternatives for configuration and operation
- On-screen menus navigated using front panel controls
- Product configuration software connected via Ethernet, USB, or RS-232
- Serial commands sent over Ethernet, RS-232 or USB connection
- Support disabling of front panel controls to prevent inadvertent or unauthorized changes to configuration settings
- Support triggering of standard CEC commands at main HDMI and DTP2 outputs
- Provide control connections
- General Requirements
- Enclosure shall be rack-mountable, full rack width, and 1RU in height
- Shall be equipped with an internal 100-240 VAC, 50/60 Hz universal power supply
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class A, ICES, and VCCI
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide three year parts and labor warranty
- Video Input Requirements
- Approved device shall be the Extron IN1808 IPCP Q MA 70 (part number 60-1615-93A); no alternates or equals
- Rack-mountable scaler and switcher for DisplayPort and HDMI video sources and associated digital and analog audio
アイテムをカートに追加する
Order Message Number
製品番号
注: Extron products using the Universal AC Outlet accept a number of different AC plug types. Before use, ensure that the device meets all regulatory requirements for your region and complies with all applicable local safety and electrical codes and standards.
現在の合計金額:
Annotation Graphics Processor
To view this page ensure that Adobe Flash Player version
11.0.0 or greater is installed and enabled.
製品をEメールでシェア
IN1808シリーズ
8入力4K/60対応シームレスプレゼンテーションスイッチャー
Eメールアドレスを正しく入力してください。
ありがとうございます。Emailの送信が完了しました。
Eメール送信中にエラーが発生しました。しばらくしてからもう一度お試しください。
Chrome
Firefox
Edge
Safari