最近閲覧した製品
XPA 2002
コンサルタント向け資料
製品番号を選択してください:
テキストをコピー
コピーされました!
エラーが発生しました。しばらくしてからもう一度お試しください。
XPA 2002-100V
- Provide a compact, energy efficient audio amplifier that shall support two analog inputs and two amplified outputs with 200 watts rms per channel into a 100 volt line.
- Compact stereo amplifier with 200 watts rms power output per channel into a 100 volt line and ENERGY STAR® qualification
- Input Requirements
- Shall support two, balanced or unbalanced line level signals on two 3-pole, 3.5 mm captive screw connectors
- Output Requirements
- Shall support two high impedance speaker level signals on two 2-pole, 5 mm screw-lock captive screw connectors
- Shall provide a total of 400 watts rms output power with 200 watts rms per channel into a 100 volt line measured at 1 kHz with 0.1% THD
- Shall provide a signal-to-noise ratio of 100 dB measured from 20 Hz to 20 kHz, unweighted
- Shall provide a minimum load impedance of 50 ohms
- Shall provide a THD+N measurement of 0.1% measured at 3 dB below clipping
- Shall provide a damping factor of greater than 100 at 50 ohms
- Shall provide a switch-selectable high pass filter for frequencies below 80 Hz with a 12 dB per octave rolloff
- Amplifier Requirements
- Shall utilize an efficient Class D amplifier design
- Shall provide Class D Ripple Suppression technology
- Shall be convection cooled and operate without fans or vents
- Shall provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain without audible artifacts to eliminate clipping distortion
- Shall provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults
- Shall provide power factor correction technology to remove harmonic content on the AC power line
- Power Requirements
- Shall draw 89.6 watts during typical (1/8 power) operation
- Shall draw 25.1 watts during quiescent operation
- Shall provide a low power standby mode
- Shall enter standby mode after 25 minutes (+/- 5 minutes) of inactivity
- Shall draw less than 1 watt while in standby mode
- Shall return to full power status in less than one second upon signal detection while in standby mode
- Shall feature an input signal detection threshold of -40 dBu, +/- 3 dB on a balanced input to deactivate standby mode
- Shall be ENERGY STAR qualified
- Shall provide an internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Control Requirements
- Shall support remote standby control on one 2-pole, 3.5 mm captive screw connector
- Front Panel Requirements
- Shall provide an LED for power indication that lights green when the unit is receiving power and active, and lights amber when the unit is in standby mode
- Shall provide an LED for indication of the enclosure temperature exceeding the optimal value
- Shall provide green LEDs for input signal presence indication
- Shall provide red LEDs for indication of clip warning and protection circuit activation
- Rear Panel Requirements
- Shall provide two inputs on two 3-pole, 3.5 mm captive screw connectors
- Shall provide two outputs on two 2-pole, 5 mm screw-lock captive screw connectors
- Shall support 22 AWG to 12 AWG speaker cables
- Shall provide standby control port on one 2-pole, 3.5 mm captive screw connector
- Shall provide recessed, detented potentiometers for attenuation adjustment
- Shall provide a switch for selecting a high pass filter to roll off frequencies below 80 Hz with a 12 dB per octave rolloff
- Shall provide an L ED for power indication that lights green when the unit is receiving power and active, and lights amber when the unit is in standby mode
- Shall provide green LEDs for input signal presence indication
- Shall provide red LEDs for indication of clip warning and protection circuit activation
- General Requirements
- Shall be enclosed in a rack-mountable 1U, full rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under BSMI, CCC, CE, c-UL, GS, KC Mark, PSE, S-Mark, and UL
- Shall meet UL 60065, IEC 60065, and BSEN 60065 for safety
- Shall meet EMI/EMC compliances under CE, CISPR 22 Class B, CISPR 24, C-tick, EN55103-1, EN55103-2, FCC Class B, ICES, KCC, and VCCI Class B
- Shall comply under the appropriate requirements of ENERGY STAR, EU code of conduct, RoHS, and WEEE
- Shall provide three years parts and labor warranty
- Input Requirements
- Approved device shall be the Extron XPA 2002-100V, part number 60-883-12; no alternates or equals.
- Compact stereo amplifier with 200 watts rms power output per channel into a 100 volt line and ENERGY STAR® qualification
XPA 2002-100V
- Provide a compact, energy efficient audio amplifier that shall support two analog inputs and two amplified outputs with 200 watts rms per channel into a 100 volt line.
- Compact stereo amplifier with 200 watts rms power output per channel into a 100 volt line and ENERGY STAR® qualification
- Input Requirements
- Shall support two, balanced or unbalanced line level signals on two 3-pole, 3.5 mm captive screw connectors
- Output Requirements
- Shall support two high impedance speaker level signals on two 2-pole, 5 mm screw-lock captive screw connectors
- Shall provide a total of 400 watts rms output power with 200 watts rms per channel into a 100 volt line measured at 1 kHz with 0.1% THD
- Shall provide a signal-to-noise ratio of 100 dB measured from 20 Hz to 20 kHz, unweighted
- Shall provide a minimum load impedance of 50 ohms
- Shall provide a THD+N measurement of 0.1% measured at 3 dB below clipping
- Shall provide a damping factor of greater than 100 at 50 ohms
- Shall provide a switch-selectable high pass filter for frequencies below 80 Hz with a 12 dB per octave rolloff
- Amplifier Requirements
- Shall utilize an efficient Class D amplifier design
- Shall provide Class D Ripple Suppression technology
- Shall be convection cooled and operate without fans or vents
- Shall provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain without audible artifacts to eliminate clipping distortion
- Shall provide multiple protection circuits that activate during output shorts, thermal overload, or DC faults
- Shall provide power factor correction technology to remove harmonic content on the AC power line
- Power Requirements
- Shall draw 89.6 watts during typical (1/8 power) operation
- Shall draw 25.1 watts during quiescent operation
- Shall provide a low power standby mode
- Shall enter standby mode after 25 minutes (+/- 5 minutes) of inactivity
- Shall draw less than 1 watt while in standby mode
- Shall return to full power status in less than one second upon signal detection while in standby mode
- Shall feature an input signal detection threshold of -40 dBu, +/- 3 dB on a balanced input to deactivate standby mode
- Shall be ENERGY STAR qualified
- Shall provide an internal universal power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Control Requirements
- Shall support remote standby control on one 2-pole, 3.5 mm captive screw connector
- Front Panel Requirements
- Shall provide an LED for power indication that lights green when the unit is receiving power and active, and lights amber when the unit is in standby mode
- Shall provide an LED for indication of the enclosure temperature exceeding the optimal value
- Shall provide green LEDs for input signal presence indication
- Shall provide red LEDs for indication of clip warning and protection circuit activation
- Rear Panel Requirements
- Shall provide two inputs on two 3-pole, 3.5 mm captive screw connectors
- Shall provide two outputs on two 2-pole, 5 mm screw-lock captive screw connectors
- Shall support 22 AWG to 12 AWG speaker cables
- Shall provide standby control port on one 2-pole, 3.5 mm captive screw connector
- Shall provide recessed, detented potentiometers for attenuation adjustment
- Shall provide a switch for selecting a high pass filter to roll off frequencies below 80 Hz with a 12 dB per octave rolloff
- Shall provide an L ED for power indication that lights green when the unit is receiving power and active, and lights amber when the unit is in standby mode
- Shall provide green LEDs for input signal presence indication
- Shall provide red LEDs for indication of clip warning and protection circuit activation
- General Requirements
- Shall be enclosed in a rack-mountable 1U, full rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under BSMI, CCC, CE, c-UL, GS, KC Mark, PSE, S-Mark, and UL
- Shall meet UL 60065, IEC 60065, and BSEN 60065 for safety
- Shall meet EMI/EMC compliances under CE, CISPR 22 Class B, CISPR 24, C-tick, EN55103-1, EN55103-2, FCC Class B, ICES, KCC, and VCCI Class B
- Shall comply under the appropriate requirements of ENERGY STAR, EU code of conduct, RoHS, and WEEE
- Shall provide three years parts and labor warranty
- Input Requirements
- Approved device shall be the Extron XPA 2002-100V, part number 60-883-12; no alternates or equals.
- Compact stereo amplifier with 200 watts rms power output per channel into a 100 volt line and ENERGY STAR® qualification
アイテムをカートに追加する
Order Message Number
製品番号
注: Extron products using the Universal AC Outlet accept a number of different AC plug types. Before use, ensure that the device meets all regulatory requirements for your region and complies with all applicable local safety and electrical codes and standards.
現在の合計金額:
製品をEメールでシェア

XPA 2002
2チャンネルパワーアンプ(200 W×2)
Eメールアドレスを正しく入力してください。
ありがとうございます。Emailの送信が完了しました。
Eメール送信中にエラーが発生しました。しばらくしてからもう一度お試しください。