最近閲覧した製品
USB Extender Plusシリーズ
コンサルタント向け資料
製品番号を選択してください:
テキストをコピー
コピーされました！
エラーが発生しました。しばらくしてからもう一度お試しください。
USB Extender Plus T
- Provide a transmitter for extending signals from USB peripheral devices such as human interface devices, imaging devices, mass storage devices, and other USB devices over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair transmitter for USB peripherals
- Shall be paired with a receiver to provide extension of USB peripheral devices up to 330 feet (100 meters) from the host device over one CATx twisted pair cable
- Shall be paired with a receiver through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall support up to four receivers via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
-
Shall support USB 2.0, 1.1, or 1.0 peripherals
-
-
- Shall provide connection for the host computer on one USB Type B connector located on the rear panel
- Shall provide peripheral emulation for a virtual connection of a keyboard and mouse to the host computer
- Shall provide the capability to configure the unit with peripheral emulation disabled
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the transmitter on one 2.5 mm tip, ring, sleeve connector located on the front panel
- Shall provide a recessed button located on the front panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Rack mountable with optional rack shelf or rack mounting brackets
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, and host status
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Approved device shall be the Extron USB Extender Plus T (60-1471-12); no alternates or equals
- Twisted pair transmitter for USB peripherals
USB Extender Plus T
- Provide a transmitter for extending signals from USB peripheral devices such as human interface devices, imaging devices, mass storage devices, and other USB devices over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair transmitter for USB peripherals
- Shall be paired with a receiver to provide extension of USB peripheral devices up to 330 feet (100 meters) from the host device over one CATx twisted pair cable
- Shall be paired with a receiver through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall support up to four receivers via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
-
Shall support USB 2.0, 1.1, or 1.0 peripherals
-
-
- Shall provide connection for the host computer on one USB Type B connector located on the rear panel
- Shall provide peripheral emulation for a virtual connection of a keyboard and mouse to the host computer
- Shall provide the capability to configure the unit with peripheral emulation disabled
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the transmitter on one 2.5 mm tip, ring, sleeve connector located on the front panel
- Shall provide a recessed button located on the front panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Rack mountable with optional rack shelf or rack mounting brackets
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, and host status
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Approved device shall be the Extron USB Extender Plus T (60-1471-12); no alternates or equals
- Twisted pair transmitter for USB peripherals
USB Extender Plus R
- Provide a receiver for extending signals from USB peripheral devices such as human interface devices, imaging devices, mass storage devices, and other USB devices over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair receiver for USB peripherals
- Shall be paired with a transmitter to provide extension of USB peripheral devices up to 330 feet (100 meters) over one CATx twisted pair cable
- Shall be paired with a transmitter through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall allow up to four receivers to be paired with a single transmitter via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide four USB Type A ports located on the rear panel for simultaneous connection of up to four USB peripheral devices
- Each USB port shall provide 5 VDC, 500 mA power
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the receiver on one 2.5 mm tip, ring, sleeve connector located on the front panel
- Shall provide a recessed button located on the front panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Rack mountable with optional rack shelf or rack mounting brackets
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, host status, and port activity between an active host and each connected peripheral device
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Approved device shall be the Extron USB Extender Plus R (60-1471-13); no alternates or equals
- Twisted pair receiver for USB peripherals
USB Extender Plus R
- Provide a receiver for extending signals from USB peripheral devices such as human interface devices, imaging devices, mass storage devices, and other USB devices over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair receiver for USB peripherals
- Shall be paired with a transmitter to provide extension of USB peripheral devices up to 330 feet (100 meters) over one CATx twisted pair cable
- Shall be paired with a transmitter through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall allow up to four receivers to be paired with a single transmitter via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide four USB Type A ports located on the rear panel for simultaneous connection of up to four USB peripheral devices
- Each USB port shall provide 5 VDC, 500 mA power
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the receiver on one 2.5 mm tip, ring, sleeve connector located on the front panel
- Shall provide a recessed button located on the front panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Rack mountable with optional rack shelf or rack mounting brackets
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, host status, and port activity between an active host and each connected peripheral device
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Approved device shall be the Extron USB Extender Plus R (60-1471-13); no alternates or equals
- Twisted pair receiver for USB peripherals
USB Extender Plus D T
- Provide a transmitter for extending signals from USB peripheral devices such as human interface devices, imaging devices, mass storage devices, and other USB devices over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair transmitter for USB peripherals
- Shall be paired with a receiver to provide extension of USB peripheral devices up to 330 feet (100 meters) from the host device over one CATx twisted pair cable
- Shall be paired with a receiver through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall support up to four receivers via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide connection for the host computer on one USB Type mini B connector located on the front panel
- Shall provide peripheral emulation for a virtual connection of a keyboard and mouse to the host computer
- Shall provide the capability to configure the unit with peripheral emulation disabled
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the transmitter on one 2.5 mm tip, ring, sleeve connector located on the rear panel
- Shall provide a recessed button located on the rear panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a wall-mountable enclosure that fits within standard US one-gang electrical box
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, and host status
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a wall-mountable enclosure that fits within standard US one-gang electrical box
- Approved device shall be the Extron USB Extender Plus D T (60-1473-13); no alternates or equals
- Twisted pair transmitter for USB peripherals
USB Extender Plus D T
- Provide a transmitter for extending signals from USB peripheral devices such as human interface devices, imaging devices, mass storage devices, and other USB devices over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair transmitter for USB peripherals
- Shall be paired with a receiver to provide extension of USB peripheral devices up to 330 feet (100 meters) from the host device over one CATx twisted pair cable
- Shall be paired with a receiver through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall support up to four receivers via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide connection for the host computer on one USB Type mini B connector located on the front panel
- Shall provide peripheral emulation for a virtual connection of a keyboard and mouse to the host computer
- Shall provide the capability to configure the unit with peripheral emulation disabled
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the transmitter on one 2.5 mm tip, ring, sleeve connector located on the rear panel
- Shall provide a recessed button located on the rear panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a wall-mountable enclosure that fits within standard US one-gang electrical box
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, and host status
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a wall-mountable enclosure that fits within standard US one-gang electrical box
- Approved device shall be the Extron USB Extender Plus D T (60-1473-13); no alternates or equals
- Twisted pair transmitter for USB peripherals
USB Extender Plus D R
- Provide a receiver for extending signals from USB peripheral devices such as human interface devices, imaging devices, mass storage devices, and other USB devices over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair receiver for USB peripherals
- Shall be paired with a transmitter to provide extension of USB peripheral devices up to 330 feet (100 meters) over one CATx twisted pair cable
- Shall be paired with a transmitter through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall allow up to four receivers to be paired with a single transmitter via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide four USB Type A ports located on the front panel for simultaneous connection of up to four USB peripheral devices
- Each USB port shall provide 5 VDC, 500 mA power
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the receiver on one 2.5 mm tip, ring, sleeve connector located on the rear panel
- Shall provide a recessed button located on the rear panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a wall-mountable enclosure that fits within standard US one-gang electrical box
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, host status, and port activity between an active host and each connected peripheral device
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a wall-mountable enclosure that fits within standard US one-gang electrical box
- Approved device shall be the Extron USB Extender Plus D R (60-1473-23); no alternates or equals
- Twisted pair receiver for USB peripherals
USB Extender Plus D R
- Provide a receiver for extending signals from USB peripheral devices such as human interface devices, imaging devices, mass storage devices, and other USB devices over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair receiver for USB peripherals
- Shall be paired with a transmitter to provide extension of USB peripheral devices up to 330 feet (100 meters) over one CATx twisted pair cable
- Shall be paired with a transmitter through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall allow up to four receivers to be paired with a single transmitter via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide four USB Type A ports located on the front panel for simultaneous connection of up to four USB peripheral devices
- Each USB port shall provide 5 VDC, 500 mA power
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the receiver on one 2.5 mm tip, ring, sleeve connector located on the rear panel
- Shall provide a recessed button located on the rear panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a wall-mountable enclosure that fits within standard US one-gang electrical box
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, host status, and port activity between an active host and each connected peripheral device
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a wall-mountable enclosure that fits within standard US one-gang electrical box
- Approved device shall be the Extron USB Extender Plus D R (60-1473-23); no alternates or equals
- Twisted pair receiver for USB peripherals
USB Extender Plus AAP R
- Provide a receiver for extending signals from USB peripheral devices such as human interface devices, imaging devices, mass storage devices, and other USB devices over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair receiver for USB peripherals
- Shall be paired with a transmitter to provide extension of USB peripheral devices up to 330 feet (100 meters) over one CATx twisted pair cable
- Shall be paired with a transmitter through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall allow up to four receivers to be paired with a single transmitter via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide four USB Type A ports located on the front panel for simultaneous connection of up to four USB peripheral devices
- Each USB port shall provide 5 VDC, 500 mA power
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the receiver on one 2.5 mm tip, ring, sleeve connector located on the rear panel
- Shall provide a recessed button located on the rear panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a furniture or floor box-mountable enclosure
- Shall provide LED indicators located on the front panel for power, link status, host status, and port activity between an active host and each connected peripheral device
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Approved device shall be the Extron USB Extender Plus AAP R (60-1472-22 or 60-1472-23); no alternates or equals
- Twisted pair receiver for USB peripherals
USB Extender Plus AAP R
- Provide a receiver for extending signals from USB peripheral devices such as human interface devices, imaging devices, mass storage devices, and other USB devices over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair receiver for USB peripherals
- Shall be paired with a transmitter to provide extension of USB peripheral devices up to 330 feet (100 meters) over one CATx twisted pair cable
- Shall be paired with a transmitter through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall allow up to four receivers to be paired with a single transmitter via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide four USB Type A ports located on the front panel for simultaneous connection of up to four USB peripheral devices
- Each USB port shall provide 5 VDC, 500 mA power
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the receiver on one 2.5 mm tip, ring, sleeve connector located on the rear panel
- Shall provide a recessed button located on the rear panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a furniture or floor box-mountable enclosure
- Shall provide LED indicators located on the front panel for power, link status, host status, and port activity between an active host and each connected peripheral device
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Approved device shall be the Extron USB Extender Plus AAP R (60-1472-22 or 60-1472-23); no alternates or equals
- Twisted pair receiver for USB peripherals
USB Extender Plus T HID
- Provide a transmitter for extending signals from USB human interface peripheral devices only, over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair transmitter for USB peripherals
- Shall be paired with a receiver to provide extension of USB peripheral devices up to 330 feet (100 meters) from the host device over one CATx twisted pair cable
- Shall be paired with a receiver through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall support up to four receivers via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide connection for the host computer on one USB Type B connector located on the rear panel
- Shall provide peripheral emulation for a virtual connection of a keyboard and mouse to the host computer
- Shall provide the capability to configure the unit with peripheral emulation disabled
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the transmitter on one 2.5 mm tip, ring, sleeve connector located on the front panel
- Shall provide a recessed button located on the front panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Rack mountable with optional rack shelf or rack mounting brackets
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, and host status
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Approved device shall be the Extron USB Extender Plus T HID (60-1539-12); no alternates or equals
- Twisted pair transmitter for USB peripherals
USB Extender Plus T HID
- Provide a transmitter for extending signals from USB human interface peripheral devices only, over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair transmitter for USB peripherals
- Shall be paired with a receiver to provide extension of USB peripheral devices up to 330 feet (100 meters) from the host device over one CATx twisted pair cable
- Shall be paired with a receiver through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall support up to four receivers via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide connection for the host computer on one USB Type B connector located on the rear panel
- Shall provide peripheral emulation for a virtual connection of a keyboard and mouse to the host computer
- Shall provide the capability to configure the unit with peripheral emulation disabled
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the transmitter on one 2.5 mm tip, ring, sleeve connector located on the front panel
- Shall provide a recessed button located on the front panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Rack mountable with optional rack shelf or rack mounting brackets
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, and host status
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Approved device shall be the Extron USB Extender Plus T HID (60-1539-12); no alternates or equals
- Twisted pair transmitter for USB peripherals
USB Extender Plus R HID
- Provide a receiver for extending signals from USB human interface peripheral devices only, over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair receiver for USB peripherals
- Shall be paired with a transmitter to provide extension of USB peripheral devices up to 330 feet (100 meters) over one CATx twisted pair cable
- Shall be paired with a transmitter through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall allow up to four receivers to be paired with a single transmitter via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide four USB Type A ports located on the rear panel for simultaneous connection of up to four USB peripheral devices
- Each USB port shall provide 5 VDC, 500 mA power
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the receiver on one 2.5 mm tip, ring, sleeve connector located on the front panel
- Shall provide a recessed button located on the front panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Rack mountable with optional rack shelf or rack mounting brackets
- Shall be available in a wall-mountable enclosure that fits within standard US one-gang electrical box
- Rack mountable with optional rack shelf or rack mounting brackets
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, host status, and port activity between an active host and each connected peripheral device
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Approved device shall be the Extron USB Extender Plus R HID (60-1539-13); no alternates or equals
- Twisted pair receiver for USB peripherals
USB Extender Plus R HID
- Provide a receiver for extending signals from USB human interface peripheral devices only, over a single CATx cable in a point-to-point configuration or via a Gigabit Ethernet network.
- Twisted pair receiver for USB peripherals
- Shall be paired with a transmitter to provide extension of USB peripheral devices up to 330 feet (100 meters) over one CATx twisted pair cable
- Shall be paired with a transmitter through a Gigabit Ethernet switch to provide extension of USB peripheral devices up to 660 feet (200 meters) from the host device within an IP network
- Shall allow up to four receivers to be paired with a single transmitter via an IP network using a Gigabit Ethernet switch
- Shall be compatible with up to five Gigabit Ethernet switches to provide extension of USB peripheral devices up to 1,980 feet (600 meters) within an IP network
- Shall support USB 2.0, 1.1, or 1.0 peripherals
- Shall support USB 3.0 peripherals that can operate at USB 2.0 rates
- Shall support data transfer rates up to 480 Mbps
- Shall provide four USB Type A ports located on the rear panel for simultaneous connection of up to four USB peripheral devices
- Each USB port shall provide 5 VDC, 500 mA power
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel
- Shall provide connection for RS-232 configuration of the receiver on one 2.5 mm tip, ring, sleeve connector located on the front panel
- Shall provide a recessed button located on the front panel to pair a transmitter to a receiver
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Rack mountable with optional rack shelf or rack mounting brackets
- Shall be available in a wall-mountable enclosure that fits within standard US one-gang electrical box
- Rack mountable with optional rack shelf or rack mounting brackets
- Wall or furniture mountable with optional mounting kits
- Shall provide LED indicators located on the front panel for power, link status, host status, and port activity between an active host and each connected peripheral device
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width, low profile metal enclosure
- Approved device shall be the Extron USB Extender Plus R HID (60-1539-13); no alternates or equals
- Twisted pair receiver for USB peripherals
USB Plus Matrix Controller
- Provide a matrix controller for switching USB signals using up to 64 USB Extender Plus Series transmitters and receivers connected to USB hosts and peripherals such as human interface devices, imaging devices, mass storage devices, and other USB devices over CATx cable via a Gigabit Ethernet network.
- Twisted pair matrix controller for up to 64 USB Extender Plus Series transmitters and receivers
- Shall support central control of USB Extender Plus transmitters and receivers using CATx cabling connected to an Ethernet network
- Shall support 10/100/100Base-T Ethernet
- Shall support Extron PCS software for matrix configuration and loading transmitter and receiver IP address information
- Shall support simple SIS commands to control USB switching using an Extron control system or a third party control system
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel for communication with USB Extender Plus Series transmitters/receivers and for integration into a control system
- Shall provide one (1) bidirectional RS-232 connector on rear panel for integration into a control system
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width metal enclosure
- Compact, low profile enclosure allows discreet installation
- Shall provide front panel port status indicators for Tx, Rx, RTS, and CTS
- Shall be plenum rated to meet UL 2043 standards for heat and smoke release, excluding power supply
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width metal enclosure
- Approved device shall be the Extron USB Plus Matrix Controller (42-267-01); no alternates or equals
- Twisted pair matrix controller for up to 64 USB Extender Plus Series transmitters and receivers
USB Plus Matrix Controller
- Provide a matrix controller for switching USB signals using up to 64 USB Extender Plus Series transmitters and receivers connected to USB hosts and peripherals such as human interface devices, imaging devices, mass storage devices, and other USB devices over CATx cable via a Gigabit Ethernet network.
- Twisted pair matrix controller for up to 64 USB Extender Plus Series transmitters and receivers
- Shall support central control of USB Extender Plus transmitters and receivers using CATx cabling connected to an Ethernet network
- Shall support 10/100/100Base-T Ethernet
- Shall support Extron PCS software for matrix configuration and loading transmitter and receiver IP address information
- Shall support simple SIS commands to control USB switching using an Extron control system or a third party control system
- Shall provide connection for twisted pair cable on one female RJ-45 connector located on the rear panel for communication with USB Extender Plus Series transmitters/receivers and for integration into a control system
- Shall provide one (1) bidirectional RS-232 connector on rear panel for integration into a control system
- Shall provide connection for 12 VDC power on one 2-pole, 3.5 mm captive screw connector located on the rear panel
- Shall be equipped with an external, universal AC power supply capable of supporting 100 - 240 VAC, 50/60 Hz power
- General requirements
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width metal enclosure
- Compact, low profile enclosure allows discreet installation
- Shall provide front panel port status indicators for Tx, Rx, RTS, and CTS
- Shall be plenum rated to meet UL 2043 standards for heat and smoke release, excluding power supply
- Shall meet regulatory compliances
- CE, c-UL, UL
- CE, C-tick, FCC Class A, ICES, VCCI
- RoHS, WEEE
- Shall provide at least three years parts and labor warranty
- Shall be available in a 1-inch (2.5 cm) high, quarter rack width metal enclosure
- Approved device shall be the Extron USB Plus Matrix Controller (42-267-01); no alternates or equals
- Twisted pair matrix controller for up to 64 USB Extender Plus Series transmitters and receivers
アイテムをカートに追加する
Order Message Number
製品番号
注: Extron products using the Universal AC Outlet accept a number of different AC plug types. Before use, ensure that the device meets all regulatory requirements for your region and complies with all applicable local safety and electrical codes and standards.
現在の合計金額:
Annotation Graphics Processor
To view this page ensure that Adobe Flash Player version
11.0.0 or greater is installed and enabled.
製品をEメールでシェア
USB Extender Plusシリーズ
USBツイストペアエクステンダー
Eメールアドレスを正しく入力してください。
ありがとうございます。Emailの送信が完了しました。
Eメール送信中にエラーが発生しました。しばらくしてからもう一度お試しください。
Chrome
Firefox
Edge
Safari