最近閲覧した製品
SM 26
コンサルタント向け資料
製品番号を選択してください:
テキストをコピー
コピーされました！
エラーが発生しました。しばらくしてからもう一度お試しください。
SM 26
- Provide a two-way, 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
- Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
- Driver Requirements
- Shall consist of a 6.5" (16.5 cm) polypropylene woofer
- Shall consist of a 1" (2.5 cm) silk dome tweeter
- Performance Requirements
- Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
- Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Shall provide a crossover frequency of 2.5 kHz
- Electrical Requirements
- Shall support 8 ohm direct connection from power amplifiers
- Shall provide an internal overload protection circuit
- Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
- Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
- Shall have a black or white finish
- Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
- Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
- Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
- Shall weigh 8.4 lbs (3.81 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall support all incoming and pass-through wiring for speaker
- Shall have a black or white finish to match speaker
- Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
- Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 26, part number 60-1308-02 or 60-1308-03; no alternates or equals.
- Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
SM 26
- Provide a two-way, 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
- Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
- Driver Requirements
- Shall consist of a 6.5" (16.5 cm) polypropylene woofer
- Shall consist of a 1" (2.5 cm) silk dome tweeter
- Performance Requirements
- Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
- Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Shall provide a crossover frequency of 2.5 kHz
- Electrical Requirements
- Shall support 8 ohm direct connection from power amplifiers
- Shall provide an internal overload protection circuit
- Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
- Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
- Shall have a black or white finish
- Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
- Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
- Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
- Shall weigh 8.4 lbs (3.81 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall support all incoming and pass-through wiring for speaker
- Shall have a black or white finish to match speaker
- Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
- Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 26, part number 60-1308-02 or 60-1308-03; no alternates or equals.
- Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
SM 26
- Provide a two-way, 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
- Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
- Driver Requirements
- Shall consist of a 6.5" (16.5 cm) polypropylene woofer
- Shall consist of a 1" (2.5 cm) silk dome tweeter
- Performance Requirements
- Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
- Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Shall provide a crossover frequency of 2.5 kHz
- Electrical Requirements
- Shall support 8 ohm direct connection from power amplifiers
- Shall provide an internal overload protection circuit
- Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
- Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
- Shall have a black or white finish
- Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
- Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
- Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
- Shall weigh 8.4 lbs (3.81 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall support all incoming and pass-through wiring for speaker
- Shall have a black or white finish to match speaker
- Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
- Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 26, part number 60-1308-02 or 60-1308-03; no alternates or equals.
- Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
SM 26
- Provide a two-way, 8 ohm surface mount speaker that shall accommodate division-of-labor installations.
- Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
- Driver Requirements
- Shall consist of a 6.5" (16.5 cm) polypropylene woofer
- Shall consist of a 1" (2.5 cm) silk dome tweeter
- Performance Requirements
- Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
- Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Shall provide a crossover frequency of 2.5 kHz
- Electrical Requirements
- Shall support 8 ohm direct connection from power amplifiers
- Shall provide an internal overload protection circuit
- Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
- Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
- Shall have a black or white finish
- Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
- Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
- Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
- Shall weigh 8.4 lbs (3.81 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall support all incoming and pass-through wiring for speaker
- Shall have a black or white finish to match speaker
- Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
- Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 26, part number 60-1308-02 or 60-1308-03; no alternates or equals.
- Two-way surface mount speaker with a dual-ported enclosure, grille, crossover network, 8 ohm nominal impedance, and a concealed, lockable mounting system
SM 26T
- Provide a two-way surface mount speaker that shall provide an internal transformer and accommodate division-of-labor installations.
- Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
- Driver Requirements
- Shall consist of a 6.5" (16.5 cm) polypropylene woofer
- Shall consist of a 1" (2.5 cm) silk dome tweeter
- Performance Requirements
- Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
- Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Shall provide a crossover frequency of 2.5 kHz
- Electrical Requirements
- Shall support 8 ohm direct or 70/100 volt connection from power amplifiers
- Shall provide a six-position, through-the-grille power tap selector
- Shall provide selectable rotary switch taps for 70 volt operation, including 32, 16, 8, 4, and 2 watts, and 8 ohms direct
- Shall provide selectable rotary switch taps for 100 volt operation, including 32, 16, 8, and 4 watts, and 8 ohms direct
- Shall provide speaker tap selector and selection guide on the front of the speaker
- Shall provide an internal overload protection circuit
- Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
- Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
- Shall have a black or white finish
- Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
- Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
- Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
- Shall weigh 9.7 lbs (4.40 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall support all incoming and pass-through wiring for speaker
- Shall have a black or white finish to match speaker
- Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
- Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 26T, part number 60-1308-12 or 60-1308-13; no alternates or equals.
- Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
SM 26T
- Provide a two-way surface mount speaker that shall provide an internal transformer and accommodate division-of-labor installations.
- Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
- Driver Requirements
- Shall consist of a 6.5" (16.5 cm) polypropylene woofer
- Shall consist of a 1" (2.5 cm) silk dome tweeter
- Performance Requirements
- Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
- Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Shall provide a crossover frequency of 2.5 kHz
- Electrical Requirements
- Shall support 8 ohm direct or 70/100 volt connection from power amplifiers
- Shall provide a six-position, through-the-grille power tap selector
- Shall provide selectable rotary switch taps for 70 volt operation, including 32, 16, 8, 4, and 2 watts, and 8 ohms direct
- Shall provide selectable rotary switch taps for 100 volt operation, including 32, 16, 8, and 4 watts, and 8 ohms direct
- Shall provide speaker tap selector and selection guide on the front of the speaker
- Shall provide an internal overload protection circuit
- Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
- Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
- Shall have a black or white finish
- Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
- Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
- Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
- Shall weigh 9.7 lbs (4.40 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall support all incoming and pass-through wiring for speaker
- Shall have a black or white finish to match speaker
- Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
- Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 26T, part number 60-1308-12 or 60-1308-13; no alternates or equals.
- Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
SM 26T
- Provide a two-way surface mount speaker that shall provide an internal transformer and accommodate division-of-labor installations.
- Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
- Driver Requirements
- Shall consist of a 6.5" (16.5 cm) polypropylene woofer
- Shall consist of a 1" (2.5 cm) silk dome tweeter
- Performance Requirements
- Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
- Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Shall provide a crossover frequency of 2.5 kHz
- Electrical Requirements
- Shall support 8 ohm direct or 70/100 volt connection from power amplifiers
- Shall provide a six-position, through-the-grille power tap selector
- Shall provide selectable rotary switch taps for 70 volt operation, including 32, 16, 8, 4, and 2 watts, and 8 ohms direct
- Shall provide selectable rotary switch taps for 100 volt operation, including 32, 16, 8, and 4 watts, and 8 ohms direct
- Shall provide speaker tap selector and selection guide on the front of the speaker
- Shall provide an internal overload protection circuit
- Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
- Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
- Shall have a black or white finish
- Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
- Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
- Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
- Shall weigh 9.7 lbs (4.40 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall support all incoming and pass-through wiring for speaker
- Shall have a black or white finish to match speaker
- Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
- Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 26T, part number 60-1308-12 or 60-1308-13; no alternates or equals.
- Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
SM 26T
- Provide a two-way surface mount speaker that shall provide an internal transformer and accommodate division-of-labor installations.
- Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
- Driver Requirements
- Shall consist of a 6.5" (16.5 cm) polypropylene woofer
- Shall consist of a 1" (2.5 cm) silk dome tweeter
- Performance Requirements
- Shall provide a frequency range of 70 Hz to 18 kHz, -10 dB below average SPL, measured on-axis in full space
- Shall provide a power capacity of 60 watts (rms) continuous pink noise per IEC 60268-5 and 120 watts (rms) continuous program
- Shall provide a nominal sensitivity of 87 dB SPL (1 W, 1 m) measured in full space
- Shall provide a nominal impedance of 8 ohms
- Shall provide a crossover frequency of 2.5 kHz
- Electrical Requirements
- Shall support 8 ohm direct or 70/100 volt connection from power amplifiers
- Shall provide a six-position, through-the-grille power tap selector
- Shall provide selectable rotary switch taps for 70 volt operation, including 32, 16, 8, 4, and 2 watts, and 8 ohms direct
- Shall provide selectable rotary switch taps for 100 volt operation, including 32, 16, 8, and 4 watts, and 8 ohms direct
- Shall provide speaker tap selector and selection guide on the front of the speaker
- Shall provide an internal overload protection circuit
- Shall support one incoming and one outgoing speaker level signal on one 4-pole, 10 mm Euro-style captive screw terminal block built into 0° mounting plate
- Shall support direct wiring of speaker or support wiring of multiple speakers using loop-through wiring terminals
- Shall support a maximum wire gauge of 12 AWG per connection point for a single wire
- Shall support a maximum wire gauge of 16 AWG per connection point for two wires
- Enclosure Requirements
- Shall consist of a plastic, trapezoidal enclosure with molded grille and dual bass reflex ports
- Shall have a black or white finish
- Shall measure 12.98" (32.97 cm) in height when using 0° mounting plate
- Shall measure 8.45" (21.46 cm) in width when using 0° mounting plate
- Shall protrude 6.45" (16.38 cm) into environment from mounting surface when using 0° mounting plate
- Shall weigh 9.7 lbs (4.40 kg) per speaker when using 0° mounting plate
- Mounting Requirements
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
- Shall support both enclosure mounting and electrical connection as speaker is placed on mount
- Shall support all incoming and pass-through wiring for speaker
- Shall have a black or white finish to match speaker
- Shall include a four-position 10° mounting adapter for vertical or horizontal speaker installation with 10° of tilt downward, upward, left, or right
- Shall have a black or white finish to match speaker
- Shall provide cable raceway access on 0° mounting plate and 10° mounting adapter for surface-mounted wiring
- Shall support 180° of speaker pivot in 10° detented steps with the use of optional Extron Yoke Mount Kit that is available in black or white finish
- Shall provide a hidden locking speaker release mechanism
- Shall include a 0° mounting plate for vertical or horizontal flush-with-the-wall enclosure installation
- General Requirements
- Shall be sold in pairs
- Shall meet regulatory compliances
- Shall comply with appropriate requirements of RoHS and WEEE
- Shall provide five year parts and labor warranty
- Driver Requirements
- Approved device shall be the Extron SM 26T, part number 60-1308-12 or 60-1308-13; no alternates or equals.
- Two-way surface mount speaker with dual-ported enclosure, grille, crossover network, internal transformer for 8 ohm direct and 70/100 volt operation, and a concealed, lockable mounting system
アイテムをカートに追加する
Order Message Number
製品番号
注: Extron products using the Universal AC Outlet accept a number of different AC plug types. Before use, ensure that the device meets all regulatory requirements for your region and complies with all applicable local safety and electrical codes and standards.
現在の合計金額:
Annotation Graphics Processor
To view this page ensure that Adobe Flash Player version
11.0.0 or greater is installed and enabled.
Chrome
Firefox
Edge
Safari