| XTP T VGA |
| NOTE | The XTP T VGA transmitter and XTP R HDMI receiver can be used together, with twisted pair cables linking the transmitter and receiver, or with other Extron XTP products. |
|
|
| Video |
|---|
| Gain | Unity |
| Resolution range | Up to 1920x1200 or 1080p (HDTV) |
| Maximum pixel clock | 165 MHz |
| Formats | RGB, component video, S-video, composite video |
|
| Video input and loop-through |
|---|
| Number/signal type | 1 analog RGBHV, RGBS, RGsB, RsGsBs, bi-level and tri-level component video (YUVi or YUVp/HDTV), S-video, or composite video input
1 buffered RGBHV, RGBS, RGsB, RsGsBs, bi-level and tri-level component video (YUVi or YUVp/HDTV), S-video, or composite video loop-through |
| Connectors | 2 female 15-pin HD |
| Nominal level | 1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video |
| Minimum/maximum levels | Analog: 0.3 V to 1.45 Vp-p with no offset |
| Impedance | 75 ohms |
| Horizontal frequency | 30 kHz to 100 kHz |
| Vertical frequency | 24 Hz to 120 Hz |
|
| Interconnection between transmitter and receiver |
|---|
| Connectors | 1 female RJ-45 per unit |
| Termination standards | TIA/EIA T568B |
| Signal transmission distance | 330' (100 m) using shielded twisted pair or XTP DTP 24 cable |
| Cable requirements | Solid conductor, 24 AWG or better |
| Cable recommendations | 400 MHz bandwidth, STP (Shielded Twisted Pair) |
| NOTE | Extron XTP DTP 24 shielded twisted pair cable is stongly recommended for optimal performance. |
|
|
| Audio |
|---|
| Gain | Unbalanced output: 0 dB; balanced output: +6 |
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | <0.1%, 20 Hz - 20 kHz at nominal level |
| S/N | >90 dB, at maximum balanced output (unweighted) |
| Crosstalk | ≤-80 dB @ 1kHz, fully loaded |
| Stereo channel separation | >80 dB @ 1 kHz |
|
| Audio input |
|---|
| Number/signal type | 1 analog stereo, balanced/unbalanced or
1 analog stereo, unbalanced |
| Connectors | (1) 3.5 mm captive screw connector, 5 pole
1 female 3.5 mm mini stereo jack |
| Impedance | 10k ohms unbalanced, 20k ohms balanced |
| Nominal level | +4 dBu balanced, -10 dBV configurable |
| Maximum level | +7 dBv unbalanced |
| Input gain adjustment | -18 dB to +24 dB, 1 dB steps, adjustable |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Communications — transmitter |
|---|
| USB control ports | 1 front panel female mini USB B |
| USB standards | USB 2.0, low speed |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™) |
|
| Communications — external device (pass-through, unidirectional or bidirectional) |
|---|
| Serial control port input/output | 1 set of proprieraey signals on a female RJ-45 jack |
| Serial control port output/input | RS-232 (±5 V) via (1) 3.5 mm, 5 pole captive screw connector (uses 3 poles) (connector is shared with IR control port) |
| Baud rates | Up to 115200 baud |
| Protocol | Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none |
| Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = GND |
| Ethernet pass-through port | 1 female RJ-45 connector |
| Ethernet data rate | 10/100Base-T, half/full duplex with autodetect |
| IR control port | (1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 40 kHz |
| IR control pin configuration | 3 = GND, 4 = IR Tx, 5 = IR Rx |
|
| General |
|---|
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power consumption | |
| Device | 11.5 watts, 12 VDC |
| Device and power supply | 14.2 watts, 12 VDC |
| NOTE | Each XTP transmitter or receiver can be powered either locally by an external power supply or remotely using an optional power inserter. |
|
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on sides and top |
| Thermal dissipation | |
| Device | 38.9 BTU/hr |
| Device and power supply | 48.1 BTU/hr |
| Mounting |
| Rack mount | Yes, with optional 1U high rack shelf |
| Furniture mount | Yes, with optional under-desk mounting kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.0" H x 8.75" W x 6.0" D (half rack wide)
(2.5 cm H x 22.2 cm W x 15.2 cm D)
(Depth excludes connectors.) |
| Product weight | 1.2 lbs (0.5 kg) |
| Shipping weight | 3 lbs (2 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | CE**, c-UL, UL, C-tick, FCC Class A**, ICES, VCCI
Complies with the appropriate requirements of RoHS and WEEE. |
| NOTE | **CE and FCC testing is conducted with STP (shielded twisted pair) cable. |
|
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (4454-D12) |