| XTP CrossPoint® CP I/O Boards |
|
| Video — XTP CP 4i, XTP CP 4o |
|---|
| Gain | Unity |
| Resolution range | Up to 1920x1200*, 2K, or 1080p @ 60 Hz
*reduced blanking |
| Signal type | Single-link HDMI (or DVI-D*) |
| Digital video | RGB digital video (DVI and HDMI standards) or Y, Cr, Cb digital component video (HDMI), actively buffered (supports all single-link DVI [if using an optional adapter] and HDMI standards from 640x480 @ 60 Hz to 1920x1200 @ 60 Hz) or 2K |
| EDID and DDC | Supports Extended Display Identification Data (EDID) and Display Data Channel (DDC) data using DVI and HDMI standards. EDID and DDC signals are actively buffered. |
| HDCP | Compliant with High-bandwidth Digital Content Protection (HDCP) using DVI and HDMI standards |
| HPD | Supports hot plug detection (HPD) of display as a pass-through signal. |
| Maximum pixel clock | 165 MHz |
| Standards | DVI 1.0, HDMI 1.3, HDCP 1.1
|
| Switching speed | 200 ns (max.) |
| Video format | HDMI and DVI |
| Audio format | Analog stereo, Dolby® Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, DTS®, DTS-ES, DTS 96/24, DTS-HD High Res, DTS-HD Master Audio™, up to 8 ch PCM, Dolby Atmos |
|
| Shielded twisted pair interconnection |
|---|
| Number/signal type | 4 sets of proprietary signals |
| Connectors | 4 female RJ-45 per board |
| Signal termination standards | TIA/EIA T568B |
| Input cable length | Up to 330" (100 m) using shielded twisted pair or XTP DTP 24 cable |
| NOTE | Lower resolutions may support longer transmission distances. Transmission distance varies, depending on the signal resolution, type of cable, and source device used in the system. |
|
| Cable requirements | Solid conductor, 24 AWG or better |
| Cable recommendations | 400 MHz bandwidth, STP (shielded twisted pair) |
| NOTE | Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
|
| Control/remote — external device (pass-through) |
|---|
| Serial control pass-through ports | 4 RS-232, via 3.5 mm, 5-pole captive screw connectors (shared with IR ports) |
| Baud rates | 300 to 115200 baud |
| Protocol | 5 to 8 data bits
1 or 2 stop bits
no parity (default), even or odd parity
flow control Xon, Xoff, and none |
| Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = GND |
| Ethernet pass-through ports | 4 female RJ-45 |
| Ethernet data rate | 10/100Base-T, half/full duplex with autodetect |
| IR control ports | 4, via 3.5 mm, 5-pole captive screw connectors (shared with RS-232 ports) |
| IR control pin configuration | 3 = GND, 4 = IR Tx, 5 = IR Rx |
|
| General |
|---|
| Power | Supplied by XTP CrossPoint or XTP II CrossPoint enclosure |
| Power consumption | |
| XTP CP 4i | |
| PoE | 79 watts (XTP II CrossPoint 3200)
95 watts (XTP II CrossPoint 6400) |
| No PoE | 35 watts |
| XTP CP 4o | |
| PoE | 75 watts (XTP II CrossPoint 3200)
90 watts (XTP II CrossPoint 6400) |
| No PoE | 21 watts |
| Product weight | 2.0 lbs (0.9 kg) |
| Regulatory compliance | |
| Environmental | Complies with the appropriate requirements of RoHS, WEEE. |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (4058-D4) |