| USB Extender Plus T/R Series |
|
| USB Extender Plus T/R |
|---|
| USB extension | |
| USB standards | USB 2.0, USB 1.1, USB 1.0 compatible |
| USB host support | xHCI (USB 3.0), EHCI (USB 2.0), OHCI/UHCI (USB 1.1) |
| USB data rates | Low speed (1.5 Mbps), full speed (12 Mbps), high speed (480 Mbps) |
| Data transfer types | Bulk, Control, Interrupt, and Isochronous |
| USB host — Tx units | |
| Number/signal type | 1 USB |
| Connectors | 1 female USB type B |
| Maximum built-in USB hubs | 2 |
| Minimum built-in USB hubs | 0 |
| Optional built-in USB hubs | Peripheral emulation enabled: 1
1:n network pairing enabled: 1 |
| USB device ports — Receiver | |
| Number/signal type | (1) 4-port, USB hub |
| Connectors | 4 female USB 2.0 type A |
| Maximum built-in USB hubs | 1 |
| Minimum built-in USB hubs | 1 |
| Available USB power | 500 mA per port |
| Interconnection between transmitter and receiver | |
| NOTE | This product supports the four types of data transfer defined by USB: bulk, control, interrupt, and isochronous transfers. |
|
| Connectors | 1 female RJ-45 per unit |
| Termination standards | TIA 568B |
| Signal transmission distance | |
| Point to point | Up to 330' (100 m) |
| Over the network | Up to 1980' (600 m)** |
| NOTE | **Over the network distance is through connection of up to five network switches. |
|
| NOTE | The transmission distance varies depending on the type of cable used in the system. |
|
| Network | |
| Protocol | Ethernet |
| Transport | TCP/IP, UDP |
| All supported | IPv4, UDP, DHCP, Unicast |
| Standards | IEEE 802.3u (100Base-T), IEEE 802.3ab (1000Base-T) |
| IP Configuration | Static IP (default) or DHCP |
|
| General — USB Extender Plus T/R |
|---|
| Power supply | External |
| Transmitter | Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 0.5 A, 6 watts |
| Receiver | Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Receiver HUB power output | 5 VDC, 500 mA per port |
| Power consumption | |
| Transmitter | |
| Device | 2.5 watts |
| Device and power supply | 3.4 watts |
| Receiver | |
| Device | 12.4 watts |
| Device and power supply | 14.9 watts |
| Enclosure type | Metal |
| Enclosure dimensions | |
| USB Extender Plus Rack Mount | 1.0" H x 4.3" W x 6.0" D (quarter rack width)
(25 mm H x 109 mm W x 152 mm D)
(Depth excludes connectors.) |
| USB Extender Plus AAP | |
| Faceplate | 1.4" H x 3.5" W x 0.1 " D
(36 mm H x 89 mm W x 2.5 mm D)
Double-space AAP |
| Device | 1.4" H x 2.7" W x 1.8" D
(36 mm H x 69 mm W x 46 mm D) |
| USB Extender Plus D | |
| Faceplate | 2.6" H x 1.3" W x 0.1 " D
(66 mm H x 33 mm W x 2.5 mm D) |
| Device | 2.7" H x 1.7" W x 1.6" D
(69 mm H x 43 mm W x 41 mm D) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | UL, c-UL, CE, FCC Class A, C-Tick, RoHS, WEEE, KC*
*Only USB Extender Plus T, USB Extender Plus R, and USB Extender Plus AAP R models |
| Product warranty | 3 years parts and labor |
|
| USB Plus Matrix Controller |
|---|
| Memory | |
| SDRAM | 512 MB |
| Flash | 512 MB |
| Ethernet control | |
| Network interface controllers (NICs) | 1 |
| Connectors | 1 female RJ-45 connector |
| Data rate | 10/100/1000Base-T, half/full duplex with autodetect |
| Protocols | DHCP, DNS, HTTP, HTTPS, ICMP, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP |
| Default settings | Link speed and duplex level = autodetected
IP address = 192.168.254.250
Subnet mask = 255.255.255.0
Gateway = 0.0.0.0
DHCP = off
DNS: 127.0.0.1 |
| Serial control | |
| Quantity/type | 1 bidirectional RS-232 |
| Connectors | (1) 3.5 mm captive screw connector, 5 pole |
| Baud rate and protocol | 300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits;
no parity (default), even, or odd parity |
|
| General — USB Plus Matrix Controller |
|---|
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 0.5 A, 6 watts |
| Power input requirements | 12 VDC, 1 A, 12 watts, max.
Or power over Ethernet (PoE) (complies with PoE 802.3af, class 3) |
| Power consumption | |
| Device | 1.5 watts, 12 VDC |
| Device and power supply | 2.0 watts, 100-240 VAC, 50-60 Hz |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, no vents |
| Thermal dissipation | |
| Device | 5.2 BTU/hr |
| Device and power supply | 6.8 BTU/hr |
| Mounting | |
| Rack mount | Yes, with optional 1U rack shelf or back of the rack mounting kit |
| Furniture mount | Yes, with optional bracket kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.0" H x 4.3" W x 6.0" D (1U high, quarter rack wide)
(25 mm H x 109 mm W x 152 mm D)
(Depth excludes connectors.) |
| Product weight | 0.6 lbs (0.3 kg) |
| Regulatory compliance | CE, c-UL, UL, C-tick, FCC Class A, ICES RoHS, WEEE |
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (6475-D21) |