PowerCage^® 1600は、ラックマウント可能な光ファイバーおよびツイストペアエクステンダーボード用フレームです。1台に光ファイバートランスミッター／レシーバーボードを組み合わせて搭載可能なスロットを16スロット装備していますので、シンプルで効率の良いシステム構築および電源管理が行えます。PowerCage 1600は、ホットスワップ可能なリダンダント電源を搭載可能（オプション）、電源と温度管理を常時行うことにより信頼性の高いシステムを構築します。中断の許されない厳しい条件下でもご使用いただけます。ホットスワップ可能なモジュール式デザインを採用していますので、システムを稼動させながら現場でのボード交換やアップグレードが可能です。

仕様

PowerCage™ 1600 System
NOTE     The PowerCage FOX AEX 104 board is not compatible with the Extron FOX 3G HD-SDI extender or the FOX 3G DVC signal converter.
NOTE     The PowerCage FOX DVI, PowerCage FOX VGA, PowerCage FOX HDMI, and PowerCage FOX SR HDMI boards are not compatible with the FOX 3G HD-SDI, FOX 3G DVC, or FOX AV models.
NOTE     The PowerCage FOX boards are available in singlemode or multimode versions.
NOTE     The PowerCage FOX boards are class 1 laser products. They meet the safety regulations of IEC-60825.
Optical specifications — PowerCage FOX boards, interconnection between transmitter and receiver
Number/type	1 singlemode or 1 multimode fiber optic input and output per FOX board, up to 8 double space boards per PowerCage enclosure
NOTE     For FOX HDMI boards: Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit HDMI video with HDCP content or return data for bidirectional control/communication.
NOTE     Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to return data for bidirectional control and communication.
Connectors	2 bidirectional LC connectors per FOX board
Operating distance
Singlemode	30 km (18.75 miles) with singlemode (SM) cables with a SM board
Multimode	300 m (985') with 62.5 µm OM1 multimode (MM) cable and a MM board 1 km (3280') with 50 µm OM2 multimode (MM) cable and a MM board 2 km (6561') with 50 µm OM3/OM4 2000 MHz bandwidth laser optimized MM cable and a MM board
NOTE     Operating distance is approximate. These are typical distances. The maximum distance may be greater than these typical numbers depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks.
Nominal peak wavelength	850 nm for multimode (MM), 1310 nm for singlemode (SM)
Transmission power, singlemode or multimode	-5 dBm, typical
Maximum receiver sensitivity
Singlemode	-18 dBm, typical
Multimode	-12 dBm, typical
Optical loss budget
Singlemode	13 dB, maximum
Multimode	7 dB, maximum
Maximum channel data rate
PowerCage FOX AV boards	2.125 Gbps
Other PowerCage FOX boards	4.25 Gbps
Video — PowerCage FOX Tx/Rx VGA
NOTE     For PowerCage FOX VGA boards, the analog video input signal is digitized pixel for pixel in the transmitter, sent digitally through the fiber cable, and converted back to analog video in the receiver.
Signal Type	VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs
Gain	Unity
Pixel data bit depth	8 bits per channel, 3 channels (R, G, B)
Maximum resolution	640x480 to 1600x1200 or 480p,576p, 720p,1080i, 1080p @ 60 Hz pixel for pixel; higher resolutions up to 1920x1200 @ 60 Hz, undersampled
Video input — PowerCage FOX Tx VGA
Number/signal type	1 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs
Connector	1 female 15-pin HD
Nominal levels	0.7 Vp-p for RGB
Minimum/maximum levels	Analog: 0.3 V to 0.75 Vp-p with no offset, terminated
Impedance	75 ohms
Horizontal frequency	24 kHz to 100 kHz
Vertical frequency	40 Hz to 120 Hz
Return loss	>40 dB @ 5 MHz
Video output — PowerCage FOX Rx VGA
Number/signal type	With input from a FOXBOX Tx VGA or a FOX 500 Tx: 1 VGA-UXGA RGBHV, RGsB (follows input or can be set by user) With input from a FOXBOX Tx VGA/YUV: 1 VGA-UXGA RGBHV, component video (bi- or tri-level YUV, 480p, 576p, 720p, 1080i, 1080p)
Connector	1 female 15-pin HD
Nominal levels	1 Vp-p for Y of component video 0.7 Vp-p for RGB and for R-Y and B-Y of component video
Minimum/maximum levels	0.3 V to 0.75 Vp-p, terminated
Impedance	75 ohms
Return loss	>30 dB @ 5 MHz
DC offset	±5 mV with input at 0 offset
Video delay	1-2 frames
Sync — PowerCage FOX Tx/Rx VGA
Input type	RGBHV, RGBS, RGsB, RsGsBs
Output type	RGBHV, RGsB (follows input or can be set by user)
Input level	2.5 V to 5.0 Vp-p
Output level	TTL: 5.0 Vp-p, unterminated, on HV, for RGBHV, RGBS 0.3 Vp-p for component video (bi-level sync) or for Gs (SOG) 0.6 Vp-p for component video (tri-level sync)
Input impedance	10k ohms
Output impedance	75 ohms
Polarity	Positive or negative (follows input or can be set by user)
Video — PowerCage FOX Tx DVI, PowerCage FOX Tx/Rx DVI Plus
Resolution range
PowerCage FOX Tx DVI	640x480 to 1600x1200 or 480p,576p, 720p,1080i, 1080p @ 60 Hz pixel for pixel; higher resolutions up to 1920x1200 @ 60 Hz, undersampled
PowerCage FOX Tx/Rx DVI Plus	640x480 up to 1920x1200 @ 60Hz, including 480p, 576p, 720p, 1080i, 1080p @ 60Hz, sampled pixel for pixel; higher resolution 2K (2048x1080) @ 60 Hz, undersampled
Format	RGB
Standards	DVI 1.0, HDMI
Video input — PowerCage FOX Tx DVI, PowerCage FOX Tx DVI Plus
Number/signal type	1 single link DVI-D (or HDMI*)
Connector	1 female DVI-I
NOTE     *Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output. The PowerCage FOX DVI and DVI Plus boards can be used to distribute HDMI signals if you use a DVI-to-HDMI adapter. However, when using HDMI signals, these units do not transmit audio and CEC signals. These boards do not support transmission of DVI signals with High-bandwidth Digital Content Protection (HDCP).
Video output — PowerCage FOX Rx DVI Plus
Number/signal type	1 single link DVI-D (or HDMI*)
Connector	1 female DVI-I
Nominal level	0.8 Vp-p
Video delay	1-2 frames
Video — PowerCage FOX 3G HD-SDI
NOTE     The PowerCage FOX 3G HD-SDI is a transceiver that can function as a transmitter or as a receiver. Two units are required for a transmitter-receiver system with one fiber optic cable linking the two units.
Signal Type	HD-SDI, SDI, and 3G-SDI digital video signals
Gain	Unity
Resolution	8 or 10 bits, automatic
Data rates	270 Mbps, 1.485 Gbps, 2.970 Gbps
Operation standards	SMPTE 259M-C, SMPTE 292M, SMPTE 424M, ITU-R BT.601, ITU-R BT.1120
Auto data rate lock	Yes
Video input — PowerCage FOX 3G HD-SDI transmitter
Number/signal type	1 single link SDI, HD-SDI, or 3G-SDI digital component video
Connectors	1 female BNC
Data rates	19 Mbps to 2.97 Gbps
Nominal level	0.8 Vp-p
Minimum/maximum levels	0.5 V to 1 Vp-p with no offset
Impedance	75 ohms
Return loss	≥15 dB @ 5 MHz to 1.5 GHz ≥10 dB @ 1.5 GHz to 3 GHz
DC offset (max. allowable)	5 V
Input coupling	AC
Input cable equalization	Automatic for up to -30 dB of cable loss
HD-SDI	120 m (400') using Extron RG6 cable 90 m (300') using Extron RG59 cable
SDI	150 m (500') using Extron RG6 cable 120 m (400') using Extron RG59 cable
NOTE     The transmission distance varies depending on the signal resolution and on the type of cable, graphics card, and display used in the system.
Video output — PowerCage FOX 3G HD-SDI receiver
Number/signal type	2 single link SDI, HD-SDI, or 3G-SDI digital component video
Connectors	2 female BNC
Re-clocking	Automatic for 270 Mbps, 1.485 Gbps, 2.97 Gbps, or bypassed for unrecognized rates
Nominal level	0.8 Vp-p
Minimum/maximum levels	0.5 V to 1.0 Vp-p
Impedance	75 ohms
Return loss	>25 dB @ 100 MHz
DC offset	±5 mV with input at 0 offset
Video — PowerCage FOX Tx/Rx AV
NOTE     For PowerCage FOX AV boards, the analog video input signal is digitized pixel for pixel in the transmitter, sent digitally through the fiber cable, and converted back to analog video in the receiver.
Gain	Unity
Standards
Input	NTSC 3.58, NTSC 4.43, PAL, SECAM, autodetected
Output	NTSC 3.58, PAL (follows vertical rate)
Decoder type	Adaptive 2D, digital comb filter
Video input — PowerCage FOX Tx AV
Number/signal type	1 component (Y, R-Y, B-Y), S-video, composite video
Connectors	1 x 3 female BNC or 1 female 4-pin mini DIN for S-video
Nominal levels	1.0 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for R-Y, B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	Analog: 0.3 V to 1.5 Vp-p with no offset
Impedance	75 ohms
Return loss	>30 dB for Y/VID, B-Y/C, R-Y @ 5 MHz
Input coupling	AC
Video output — PowerCage FOX Rx AV
Number/signal type	1 component (Y, R-Y, B-Y) video, S-video, composite video
Connectors	1 x 3 female BNC or 1 female 4-pin mini DIN for S-video
Nominal levels	1.0 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for R-Y, B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	0.3 V to 1.5 Vp-p
Impedance	75 ohms
Return loss	>40 dB @ 5 MHz
DC offset	+350 mV, maximum, with input at 0 offset
Video delay	1-2 frames
Video — PowerCage FOX Tx/Rx HDMI
NOTE     Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input and output.
Maximum data rate	4.25 Gbps
Maximum pixel clock	165 MHz
Maximum resolution	640x480 up to 1920x1200 @ 60Hz, including 480p, 576p, 720p, 1080i, 1080p @ 60Hz, sampled pixel for pixel; higher resolution 2K (2048x1080) @ 60 Hz, undersampled
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI, HDCP 1.1, CEA-861E
Video input — PowerCage FOX Tx HDMI
Number/signal type	1 single link HDMI
Connectors	1 female 19-pin HDMI type A
Video output — PowerCage FOX Rx HDMI
Number/signal type	1 single link HDMI
Connectors	1 female 19-pin HDMI type A
Video processing — PowerCage FOX SR HDMI
Digital sampling	24 bit, 8 bits per color, 165 MHz standard
Colors	16.78 million
Video output — PowerCage FOX SR HDMI
NOTE     Appropriate HDMI to DVI-D cables or adapters are required for DVI signal output.
Number/signal type	1 single link HDMI (HDCP compliant)
Connectors	1 female HDMI type A
Nominal level	0.8 Vp-p
Video delay	1-2 frames
Scaled resolution	640x4806,8,9, 800x6006,8,9, 852x4806,8,9, 1024x7686,8,9, 1024x8526,8,9, 1024x10246,8,9, 1280x7686,8,9, 1280x8006,8,9, 1280x10246,8,9, 1360x7656,8,9, 1360x7686,8,9, 1365x7686,8,9, 1365x10246,8,9, 1366x7686,8,9, 1400x10506,8, 1440x9006,8,9, 1600x12006,8, 1680x10506,8, 1920x12006,8 HDTV: 480p7,8, 576p6, 720p3,4,5,6,7,8, 1080i6,7,8, 1080p1,2,3,4,5,6,7,8, 2048x10801,2,3,4,5,6,7,8
	1 = 23.98 Hz, 2 = 24 Hz, 3 = 25 Hz, 4 = 29.97 Hz, 5 = 30 Hz, 6 = 50 Hz, 7 = 59.94 Hz, 8 = 60 Hz, 9 = 75 Hz
Video — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ
Gain	Unity
Number/signal type	1 set of proprietary analog signals
Connector	1 female RJ-45
Video input — PowerCage MTP T 15HD RSA
Number/signal type	1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (YUVi or YUVp/HDTV), S-video, or composite video
Connector	1 female 15-pin HD
Nominal levels	1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	0.3 V to 1.45 Vp-p
Impedance	75 ohms
Horizontal frequency	15 kHz to 130 kHz
Vertical frequency	30 Hz to 150 Hz
Return loss	<-30 dB @ 5 MHz
DC offset (max. allowable)	250 mV
Video output — PowerCage MTP R 15HD RSA SEQ
Number/signal type	1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, component video (YUVi or YUVp/HDTV), S-video, or composite video
Connector	1 female 15-pin HD
Nominal levels	1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video
Minimum/maximum levels	0.3 V to 1.45 Vp-p
Impedance	75 ohms
Return loss	<-30 dB @ 5 MHz
DC offset	<±35 mV with input at 0 offset
Skew compensation	62 ns
Maximum resolution	Up to 1920x1200 or 2048x1080 or 1080p at 300' Up to 1024x768 at 600'
NOTE     Refer to the user guide for the maximum distances recommended for specific resolutions.
Sync — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ
Input/output type	RGBHV, RGBS, RGsB, RsGsBs
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM
Input level (transmitter)	3.5 V to 5.5 Vp-p, unterminated
Output level (receiver)	4.0 V to 5.0 Vp-p, unterminated
Input impedance (transmitter)	573 ohms ±5%
Output impedance (receiver)	110 ohms
Polarity
Transmitter	Positive or negative (follows input polarity)
Receiver	Positive or negative (switch-selectable)
Video — PowerCage MTP T AV, PowerCage MTP R AV
Gain	Unity
Differential phase error	<1.0° at 3.58 MHz and 4.43 MHz
Differential gain error	<1.0% at 3.58 MHz and 4.43 MHz
Video input — PowerCage MTP T AV
Number/signal type	1 S-video or composite video
Connectors	2 female BNC
Nominal level	1 Vp-p for Y of S-video and for composite video 0.3 Vp-p for C of S-video
Minimum/maximum levels	0.3 V to 1.5 Vp-p with no offset
Impedance	75 ohms
Return loss	<-30 dB, DC @ 10 MHz
DC offset (max. allowable)	250 mV
Video output — PowerCage MTP R AV
Number/signal type	1 S-video or composite video
Connectors	2 female BNC
Nominal level	1 V p-p for Y of S-video and for composite video 0.3 V p-p for C of S-video
Minimum/maximum level	0.3 V to 1.5 Vp-p
Impedance	75 ohms
Return loss	<-35 dB @ 5 MHz
DC offset	±20 mV with input at 0 offset
Sync — PowerCage MTP T AV, PowerCage MTP R AV
Standards	NTSC 3.58, NTSC 4.43, PAL, SECAM
Audio — PowerCage FOX Tx/Rx VGA, PowerCage FOX Tx DVI, PowerCage FOX Tx/Rx DVI Plus, PowerCage FOX Tx/Rx AV, PowerCage FOX Tx/Rx HDMI, PowerCage FOX SR HDMI
NOTE     In PowerCage FOX boards, the analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver.
Gain
Range	Adjustable, -18 dB to +10 dB
Default	Unbalanced output: -6 dB; balanced output: 0 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise
VGA, DVI, HDMI, SR HDMI boards	0.10% @ 1 kHz at nominal level
AV boards	0.15% @ 1 kHz at nominal level
S/N	>80 dB at maximum output (unweighted)
CMRR	65 dB @ 20 Hz to 20 kHz
Audio bits per sample	18 bits per channel, 2 channels (L, R)
Sampling rate	48 kHz
Audio — PowerCage FOX AEX 104
NOTE     In PowerCage FOX boards, the analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver.
NOTE     The PowerCage FOX AEX 104 board is not compatible with the Extron FOX 3G HD-SDI extender or the FOX 3G DVC signal converter.
Gain	Unbalanced output: -6 dB; balanced output (default): 0 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.10% @ 1 kHz at nominal level
S/N	>80 dB at maximum output (unweighted)
Audio bits per sample	18 bits per channel, 2 channels (L, R)
Sampling rate	48 kHz
Audio input — PowerCage FOX Tx VGA, PowerCage FOX Tx DVI, PowerCage FOX Tx DVI Plus, PowerCage FOX Tx AV, PowerCage FOX Tx HDMI
Number/signal type
HDMI boards	1 stereo, unbalanced or 2 mono, unbalanced
VGA, DVI, DVI Plus, and AV boards	1 stereo, balanced/unbalanced or 2 mono, balanced/unbalanced
Connectors
HDMI boards	(1) 3.5 mm mini stereo jack
VGA, DVI, DVI Plus, and AV boards	(1) 3.5 mm captive screw connector, 5 pole
Impedance	≥10k ohms unbalanced, ≥20k ohms balanced
Nominal level
HDMI boards	-10 dBV (316 mVrms)
All other FOX boards	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level
AV boards	+17 dBV, unbalanced at 1% THD+N
VGA, DVI, DVI Plus, and HDMI boards	+8.9 dBV, unbalanced at 1% THD+N
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output — PowerCage FOX Rx VGA, PowerCage FOX Rx DVI Plus, PowerCage FOX Rx AV, PowerCage FOX Rx HDMI, PowerCage FOX SR HDMI, PowerCage FOX AEX 104
Number/signal type
AEX 104 boards	4 stereo, balanced/unbalanced or 8 mono, balanced/unbalanced
All other FOX boards	1 stereo, balanced/unbalanced or 2 mono, balanced/unbalanced
Connectors
AEX 104 boards	(4) 3.5 mm captive screw connectors, 5 pole
All other FOX boards	(1) 3.5 mm captive screw connector, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Nominal level
HDMI boards	-10 dBV (316 mVrms)
All other FOX boards	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level (Hi-Z)
VGA and DVI Plus boards	+7.6 dBu, unbalanced at 1% THD+N
AV boards	>+19 dBu, unbalanced at 1% THD+N
HDMI and AEX 104 boards	>+11.0 dBu, balanced at 1% THD+N
Maximum level (600 ohm)
VGA and DVI boards	>+6.3 dBu, unbalanced at 1% THD+N
AV boards	>+15 dBm, unbalanced at 1% THD+N
HDMI and AEX 104 boards	>+10.0 dBu, balanced at 1% THD+N
Audio delay	1.5 frames
Audio — PowerCage MTP T 15HD RSA, PowerCage MTP R 15HD RSA SEQ, PowerCage MTP T AV, PowerCage MTP R AV
Number/signal type	1 set of proprietary analog signals
Connector	1 female RJ-45
Gain	Unbalanced output: 0 dB; balanced output: +6 dB
Frequency response	20 Hz to 20 kHz, ±1 dB
THD + Noise	0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level
S/N	>70 dB at maximum output (unweighted)
Stereo channel separation	>60 dB @ 1 kHz
CMRR	>43 dB @ 20 Hz to 20 kHz
Audio input — PowerCage MTP T 15HD RSA, PowerCage MTP T AV
Number/signal type
PowerCage MTP T 15HD RSA	1 stereo, unbalanced
PowerCage MTP T AV	1 stereo, balanced/unbalanced
Connector	(1) 3.5 mm captive screw connector, 5 pole
Impedance
PowerCage MTP T 15HD RSA	>10k ohms, unbalanced
PowerCage MTP T AV	>10k ohms, unbalanced; >20k ohms, balanced; AC coupled
Nominal levels	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level	+18 dBu, (unbalanced) at 1% THD+N
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output — PowerCage MTP R 15HD RSA SEQ, PowerCage MTP R AV
Number/signal type
PowerCage MTP R 15HD RSA SEQ	1 mono, balanced/unbalanced
PowerCage MTP R AV	2 mono, balanced/unbalanced
Connector	(1) 3.5 mm captive screw connector, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±1 dB channel to channel
Nominal levels	+4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
Maximum level	+18 dBu, unbalanced at 1% THD+N
Control/remote
NOTE     PowerCage MTP AV Series boards and PowerCage FOX AEX boards do not have any RS-232 communication. PowerCage MTP 15HD Series boards have only pass-through RS-232 communication.
Serial control ports
Enclosure	1 bidirectional RS-232, 2.5 mm mini stereo jack (front panel)
PowerCage FOX boards
Control	1 bidirectional RS-232, 3.5 mm captive screw connector, 5 pole (uses 3 poles; shared with the alarm port)
Pass-through	1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used, "RS-232 Over Fiber")
PowerCage MTP 15HD boards	External device; pass-through, uni- or bidirectional Input/output: 1 set of proprietary signals on a female RJ-45 jack Output/input: 1 RS-232 via 3 poles of a 3.5 mm captive screw connector (3 pole for transmitter, 5 pole for receiver)
Baud rate and protocol
PowerCage FOX boards
Control	9600 baud, 8 data bits, 1 stop bit, no parity
Pass-through	9600 to 115,200 baud
PowerCage MTP 15HD boards
Baud rates	Up to 38400 bps at up to 600' (182.9 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.)
Protocol	Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none Defaults: 8 data bits, 1 stop bit, no parity
NOTE     For PowerCage MTP boards, protocol is mirrored between the transmitter and the receiver.
Serial control pin configurations
Captive screw connector
PowerCage FOX boards	1 = Tx, 2 = Rx, 3 = GND
PowerCage MTP 15HD boards	Transmitter: 1 = Tx, 2 = Rx, 3 = GND Receiver: 3 = GND, 4 = Tx, 5 = Rx
Mini stereo jack	RS-232: tip = Tx, ring = Rx, sleeve = GND
Program control	For FOX boards only: Extron control/configuration program for Windows® Extron Simple Instruction Set (SIS™)
General
Recommended cable type	For PowerCage MTP boards: Extron Enhanced Skew-Free™ AV UTP cable or CAT 5/5e/6 (shielded or unshielded)
Power supply	Internal, 1 or 2* (positive-negative), primary and redundant, hot-swappable 100-240 VAC, 50-60 Hz *A redundant power supply is optional.
Power consumption
System	Enclosure without boards: 12.4 watts
Individual FOX boards	FOX Tx VGA: 5.68 watts FOX Rx VGA: 6.54 watts FOX Tx DVI: 5.67 watts FOX Rx DVI: 5.50 watts FOX 3G HD-SDI: 1.84 watts FOX Tx AV: 6.89 watts FOX Rx AV: 5.57 watts FOX DVI Plus Tx: 5.68 watts FOX DVI Plus Rx: 6.18 watts FOX Tx HDMI: 6.02 watts FOX Rx HDMI: 6.02 watts FOX SR HDMI: 8.8 watts FOX AEX 104: 7.9 watts
Individual MTP boards	MTP T 15HD RSA: 4.30 watts MTP R 15HD RSA SEQ: 8.38 watts MTP T AV: 2.69 watts MTP R AV: 3.92 watts
Power input requirements for boards	12 VDC, 1.0 A, supplied by the PowerCage enclosure
Ambient temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Enclosure: fans, front to back Boards: convection, within the PowerCage enclosure
Thermal dissipation
FOX SR HDMI board	29.8 BTU/hr
FOX AEX 104	27.0 BTU/hr
All other boards	27.6 BTU/hr
Mounting — PowerCage enclosure
Rack mount	Yes
Enclosure type	Metal
Enclosure dimensions
PowerCage enclosure	5.25" H x 17.0" W x 12.25" D (3U high, full rack wide) 13.3 cm H x 43.2 cm W x 31.2 cm D (Depth excludes connectors on the optional boards.  Width excludes rack ears.)
PowerCage FOX boards	Each fits a double slot opening in a PowerCage enclosure.
PowerCage MTP R 15HD RSA SEQ	Each fits a double slot opening in a PowerCage enclosure.
All other boards	Each fits a single slot opening in a PowerCage enclosure.
Product weight
PowerCage enclosure	11.6 lbs (5.3 kg)
PowerCage FOX boards	1.1 lbs (0.5 kg)
PowerCage MTP R 15HD RSA SEQ	1.0 lbs (0.5 kg)
All other boards	0.8 lbs (0.4 kg)
Shipping weight
PowerCage enclosure	13 lbs (6 kg)
Boards	2 lbs (1 kg) each
Vibration	ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety	CE, c-UL, UL
EMI/EMC	CE, C-tick, FCC Class A, ICES, VCCI
Environmental	Complies with the appropriate requirements of RoHS, WEEE.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(8.1-121114-D15)