| NAV 10E 401 D |
|
specification |
 |
| Frame rate2 | 24, 25, 30, 50, or 60 fps |
| Chroma sampling2 | 4:4:4, 4:2:2, or 4:2:0 |
| Color bit depth2 | 8, or 10 bits per color |
| Signal Type | DVI v1.0, HDMI v1.4 and v2.0, HDCP v1.4 and v2.3 |
| Max. video data rate | 18 Gbps (6 Gbps per color) |
| NOTE | 14096 x 2160 @ 50-60 Hz is available only for HDMI connectors. |
|
| NOTE | 2Subject to the maximum data rate limit. Use our calculator at www.extron.com/8Kdatarate to determine video parameters supported by this data rate. |
|
|
| Video input and loop through |
| NOTE | *Appropriate DVI-D to HDMI or DisplayPort to HDMI cables or adapters are required for DVI or DisplayPort signal input. |
|
| Number/signal type | 1 digital HDMI video*
1 digital HDMI video (loop through) |
| Connectors | 2 female HDMI type A: 1 for input, 1 for loop through |
| Resolution range | Up to 4K (4096x2160 at 60 Hz) and UHD (3840x2160 at 60 Hz) |
| Standards | DVI v1.0, HDMI v1.4 and v2.0, HDCP v1.4/v2.3 |
|
| Video processing |
| Digital sampling | 8 or 10 bits per color; 600 MHz pixel clock maximum |
| Compression | PURE3® |
| Bit rate | 250 Mbps to 9.5 Gbps |
| Latency | <1 frame (encode/decode)** |
| NOTE | **Indicates minimum latency. Network and video processing dependencies apply. |
|
|
| Video output stream |
| Number/signal type | 1 PURE3 digital video over IP |
| Connector | 1 SFP+ connector (SM or MM) |
|
| Audio |
| Sampling Rates | 32, 44.1, 48 kHz |
| Bit depths | 16, 20, 24 bit |
|
| Audio input |
| Number/signal type | 1 digital stereo, de-embedded from HDMI |
| Connectors | 1 female HDMI type A (shared with video input) |
| Supported formats | LPCM (2 channel) |
|
| Audio output stream |
| Number/signal type | 1 audio over IP LPCM 1 audio over IP AES67* |
| Connector | 1 SFP+ connector (SM or MM) |
| NOTE | *AES67 specifications are compatible with the Extron DSPs. |
|
|
| Network interconnection (NAV) |
| Number/signal type | 2 fiber optic |
| Connectors | (1) 10G SFP+ connector, 2 LC connectors |
| Termination | MDI (SFP+) |
| Ethernet standards | 10 Gb Ethernet (802.3ae), 10GBase-LR (SFP+) SM, and 10GBase-SR (SFP+) MM |
| Protocols | |
| Streaming | SRTP (AES-128) on video and audio |
| Transport | Multicast UDP |
| All supported | DHCP, HTTPS, IGMPv2/v3, IPv4, PTPv2, QoS, SSH, TCP, UDP |
| Security | AES-256, 802.1X, Active Directory authentication |
| Signal transmission distance | |
| Singlemode | 10 km (6.25 miles) with singlemode (SM) cables with 10GBASE-LR (SFP+) |
| Multimode | 400 m (1312') with 50/125 µm OM4 cables with 10GBase-SR (SFP+) |
| NOTE | Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. |
|
| Nominal peak wavelength | 850 nm for multimode, 1310 nm for singlemode |
| Transmission power | |
| Singlemode | -5.2 dBm, minimum |
| Multimode | -2.8 dBm, minimum |
| Maximum receiver sensitivity | |
| Singlemode | -12.6 dBm, maximum |
| Multimode | -11.1 dBm, maximum |
| Optical loss budget | |
| Singlemode | 7.4 dB, maximum |
| Multimode | 8.3 dB, maximum |
|
| Network extension (EXT) |
| Connector | 1 RJ-45 female |
| Termination | Auto-MDIX, TIA/EIA T568B |
| Ethernet standards | 1GbE, (802,3ab), 10/100/1000 Base-T, half/full duplex with autodetect |
| Signal transmission distance | 330' (100 m) using CAT-5e/6/6a/7 cables |
|
| Communications - external devices |
| Serial | |
| Quantity/type | 1 bidirectional RS-232 |
| Connector | (1) 3.5 mm captive screw connector, 5 pole (shared with IR port) |
| Baud rate and protocol | 300 to 115200 baud (9600 baud = default)
8 (default) or 7 data bits
1 (default) or 2 stop bits
no parity (default), even or odd parity |
| Pin configuration | Tx, Rx, and Gnd |
| IR control | |
| Quantity/type | 1 TTL level (0 to 5 V) infrared (carrier and non-carrier) up to 300 kHz |
| Connector | (1) 3.5 mm captive screw connector, 5-pole (shared with RS-232) |
| Pin configuration | S = signal and G = Gnd |
| IR output carrier frequency | 30 kHz to 300 kHz |
| USB configuration port | |
| Quantity/type | 1 front panel USB mini-B |
| Standard | Ethernet over USB |
|
| General |
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 2.0 A, 24 watts |
| Power consumption | |
| Device | 21.7 watts |
| Device and power supply | 24.8 watts |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +104 °F (0 to +40 °C) / 10% to 85%, noncondensing |
| Cooling | Fan, air flows from bottom to top |
| Thermal dissipation | |
| Device | 73.2 BTU/hr |
| Device and power supply | 83.5 BTU/hr |
| Mounting | |
| Rack mount | No |
| Furniture or wall mount | Yes, in a standard US 3-gang electrical junction box or mud ring. |
| Enclosure type | Metal |
| Enclosure | |
| Faceplate | 4.5" H x 6.4" W x 0.72" D (11.4 cm H x 16.3 cm W x 1.82 cm D) |
| Device | 2.72" H x 5.29" W x 1.98" D* (6.9 cm H x 13.4 cm W x 5.0 cm D*) |
| NOTE | Depth excludes connectors. Fits the openings in a 3-gang decorator-style wallplate. |
|
| |  |
| Product weight | 1.45 lbs (0.66 kg) |
| Regulatory compliance | CE, c-UL UL,C-tick, FCC Class A, ICES, VCCI, Complies with the appropriate requirements of RoHS, WEEE |
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (5819-D4) |