| FOX Matrix 7200 |
| NOTE | The I/O boards are class 1 laser products. They meet the safety regulations of IEC-60825, FDA 21 CFR 1040.10, and FDA 21 CFR 1040.11. |
|
|
| Optical specifications |
|---|
| Number/type | 8 singlemode or 8 multimode fiber optic inputs and outputs (8 Tx and 8 Rx) per I/O board |
| NOTE | Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit return data for bidirectional control/communication. |
|
| Connectors | 16 LC connectors per I/O board |
| Operating distance | |
| Singlemode | 30 km (18.75 miles) with singlemode (SM) cables with an Extron singlemode transmitter/receiver |
| Multimode | 300 m (985') with 62.5 µm OM1 multimode (MM) cables with an Extron multimode Tx/Rx unit
1 km (3280') with 50 µm OM2 multimode (MM) cables with an Extron multimode Tx/Rx unit
2 km (6561') with 50 µm, OM3/OM4, 2000 MHz bandwidth, laser-optimized multimode (MM) cables with an Extron multimode Tx/Rx unit |
| NOTE | Operating distance is approximate. These are typical distances. The maximum distance may be greater than these typical numbers depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. |
|
| Nominal peak wavelength | 850 nm for multimode (MM), 1310 nm for singlemode (SM) |
| Transmission power | |
| Singlemode | -5 dBm, typical |
| Multimode | -5 dBm, typical |
| Maximum receiver sensitivity | |
| Singlemode | -18 dBm, typical |
| Multimode | -12 dBm, typical |
| Optical loss budget | |
| Singlemode | 13 dB, maximum |
| Multimode | 7 dB, maximum |
| Maximum channel data rate | 4.25 Gbps |
|
| Video — fiber optic (FOX I/O 88 SM, FOX I/O 88 MM) |
|---|
| Routing | 8 x 8 up to 72 x 72 unidirectional (Tx) matrix or
4 x 4 up to 36 x 36 bidirectional (Tx/Rx) matrix |
| Gain | Unity |
| Pixel data bit depth | 8 bits per channel, 3 channels (R, G, B) |
|
| Video/audio input or output — fiber optic (FOX I/O 88 SM, FOX I/O 88 MM) |
|---|
| Number/signal type | 8 to 72 fiber optic signals |
| Connectors | 8 LC connectors per I/O board |
| NOTE | Input comes from an Extron fiber optic transmitter, fiber optic distribution amplifier, or fiber optic matrix switcher. |
|
| NOTE | Output connects to an Extron fiber optic receiver. |
|
|
| Digital video — SDI/HD-SDI (FOX I/O HD-SDI) |
|---|
| Routing | 8 x 8 up to 72 x 72 matrix |
| Gain | Unity |
| Maximum data rate | 2.97 Gbps |
| Auto data rate lock | Yes |
| Data types | 8 or 10 bit |
| Operation standards | SMPTE 292M, SMPTE 259M, SMPTE 297-2006, SMPTE 424M, ITU-RBT.601, ITU-RBT.1120 |
|
| Digital video input — SDI/HD-SDI (FOX I/O HD-SDI) |
|---|
| Number/signal type | 8 single link SDI, HD-SDI, or 3G-SDI; or dual link HD-SDI per board |
| Connectors | 8 female BNC per board |
| Nominal level | 0.80 Vp-p ±10% |
| Impedance | 75 ohms |
| Return loss | >14 dB @ 1 MHz to 1.3 GHz |
| Equalization | Automatic |
| Input cable equalization distance | |
| 3G-SDI | |
| Extron RG6, Belden 1694A cable | 328' (100 m) |
| Extron R59, Belden 1505A cable | 218' (66 m) |
| HD-SDI | |
| Extron RG6, Belden 1694A cable | 492' (150 m) |
| Extron R59, Belden 1505A cable | 328' (100 m) |
| SDI | |
| Extron RG6, Belden 1694A cable | 984' (300 m) |
| Extron R59, Belden 1505A cable | 650' (198 m) |
| NOTE | The transmission distance varies depending on the signal resolution and on the type of cable, graphics card, and display used in the system. |
|
|
| Digital video output — SDI/HD-SDI (FOX I/O HD-SDI) |
|---|
| Number/signal type | 8 single-link SDI, HD-SDI, or 3G-SDI; or dual-link HD-SDI per board |
| Connectors | 8 female BNC per board |
| Nominal level | 0.80 Vp-p ±10% |
| Impedance | 75 ohms |
| Return loss | >12 dB @ 1 MHz to 1.3 GHz |
| DC offset | 0 V with input at 0 offset |
| Re-clocking | Automatic, or use available bypass mode for nonstandard rates |
| Jitter | <0.2 UI |
| Rise and fall time (20-80%) | 600 ps ±100 ps |
|
| Control/remote — switcher |
|---|
| Serial control port | 1 bidirectional RS-232 or RS-422, female 9-pin D connector (rear panel)
1 bidirectional RS-232, 2.5 mm mini stereo jack (front panel ) |
| Baud rate and protocol | 9600 to 115200 baud, 9600 baud (default), 8 data bits, 1 stop bit, no parity |
| Serial control pin configurations |
| Female 9-pin D connector | RS-232: 2 = Tx, 3 = Rx, 5 = GND
RS-422: 2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+ |
| Mini stereo jack | RS-232: tip = Tx, ring = Rx, sleeve = GND |
| Ethernet control port | 1 female RJ-45 connector |
| Ethernet data rate | 10/100Base-T, half/full duplex with autodetect |
| Ethernet protocol | ARP, ICMP (ping), IP, TCP, UDP, DHCP, HTTP, SMTP, SNMP, Telnet |
| Default settings | Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Gateway = 0.0.0.0
DHCP = off |
| Web server | Up to 200 simultaneous sessions
7 MB nonvolatile user memory |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™)
Microsoft® Internet Explorer® ver. 6 or higher, Telnet |
|
| General |
|---|
| Power supply | Internal, 2* (positive-negative), primary and redundant, hot-swappable
Input: 100-240 VAC, 50-60 Hz
*A redundant power supply is standard. |
| Power consumption | Enclosure without boards: 50.7 watts
Enclosure fully loaded with 9 MM boards: 165 watts
Enclosure fully loaded with 9 SM boards: 171 watts
Enclosure fully loaded with 9 SDI/HD-SDI boards: 137 watts
Each MM board: 12.6 watts
Each SM board: 13.3 watts
Each SDI/HD-SDI board: 9.5 watts |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Fan, right to left (as viewed from front panel) |
| Thermal dissipation, full load | 584 BTU/hr |
| Mounting | |
| Rack mount | Yes |
| Enclosure type | Metal |
| Enclosure dimensions | 14.0" H x 17.0" W x 12" D (8U high, full rack wide)
(35.6 cm H x 43.2 cm W x 30.5 cm D)
(Depth excludes connectors and buttons. Width excludes integrated rack ears.) |
| Product weight (fully loaded) | 61.1 lbs (27.7 kg) |
| Shipping weight | 68 lbs (31 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (8.0-032113-D8) |