| DVI 201 A D Tx/Rx |
| NOTE | *Appropriate DVI-D to HDMI cables or adapters are required for HDMI signal input/output.
Also, an optional Extron HDMI-to-DVI adapter is required in order to transmit a CEC signal. |
|
|
| Video |
|---|
| Maximum data rate | 4.95 Gbps (1.65 Gbps per color) |
| Maximum pixel clock | 165 MHz |
| Resolution range | 1920x1200 or 1080p @ 60 Hz |
| Formats | RGB and YCbCr digital video |
| Standards | DVI 1.0, HDMI |
|
| Video input and loop through — transmitters |
|---|
| Number/signal type | 1 single link DVI-D (or HDMI*) input
1 single link DVI-D (or HDMI*) local loop-through |
| Connectors | |
| DVI 201 A D Tx | 1 female DVI-I |
|
| Interconnection between transmitter and receiver |
|---|
| Connectors | 2 female RJ-45 per unit for 2 cables connecting the transmitter and receiver |
| Termination standards | TIA/EIA T568A or T568B |
| Signal transmission distance | |
| 1920x1200 or 1080p @ 60 Hz |
| Extron STP201 cable | Up to 150' (45 m) |
| CAT 5/5e/6 STP | Up to 125' (38 m) |
| CAT 5/5e/6 UTP | Up to 100' (30 m) |
| 1024x768 or 720p/1080i @ 60 Hz |
| CAT 5/5e/6 UTP or STP or Extron STP201 | Up to 200' (60 m) |
| NOTE | The transmission distance varies greatly depending on the signal resolution and on the type of cable, graphics card, and display used in the system. |
|
| NOTE | Shielded twisted pair cable provides added protection from outside interference and increases overall signal transmission distance. Extron strongly recommends using shielded twisted pair for optimal performance. |
|
|
| Video output — receivers |
|---|
| Number/signal type | 1 single link DVI-D (or HDMI*) |
| Connectors | |
| DVI 201 A D Rx | 2 female DVI-I |
|
| Audio |
|---|
| Gain | Unbalanced output: 0 dB; balanced output: +6 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.05 dB |
| THD + Noise | 0.10% @ 1 kHz at nominal level |
| S/N | >85 dB at maximum output (unweighted) |
| Stereo channel separation | >86 dB @ 1 kHz |
|
| Audio input |
|---|
| Number/signal type | |
| DVI 201 A D Tx | 1 stereo, unbalanced |
| DVI 201 A D Rx | 1 stereo, balanced/unbalanced |
| Connectors | |
| DVI 201 A D Tx | (1) 3.5 mm mini audio jack (tip, ring, sleeve) |
| DVI 201 A D Rx | (1) 3.5 mm captive screw connector, 5 pole |
| Impedance | |
| DVI 201 A D Tx | >10k ohms unbalanced, DC coupled |
| DVI 201 A D Rx | >18k ohms unbalanced, 14k ohms balanced, DC coupled |
| Nominal level | |
| DVI 201 A D Tx | -10 dBV (316 mVrms) |
| DVI 201 A D Rx | +4 dBu (1.23 Vrms) |
| Maximum level | |
| DVI 201 A D Tx | +11 dBu, unbalanced at 1% THD+N |
| DVI 201 A D Rx | +16.8 dBu, unbalanced at 1% THD+N |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output |
|---|
| Number/signal type | |
| DVI 201 A D Tx | 1 stereo, balanced/unbalanced |
| DVI 201 A D Rx | 1 stereo, unbalanced |
| Connectors | |
| DVI 201 A D Tx | (1) 3.5 mm captive screw connector, 5 pole |
| DVI 201 A D Rx | (1) 3.5 mm mini audio jack (tip, ring, sleeve) |
| Impedance | |
| DVI 201 A D Tx | 50 ohms unbalanced, 100 ohms balanced |
| DVI 201 A D Rx | 50 ohms unbalanced |
| Maximum level (Hi-Z) | |
| DVI 201 A D Tx | >+16 dBu, balanced or unbalanced at 1% THD+N |
| DVI 201 A D Rx | >+9.8 dBu, unbalanced at 1% THD+N |
| Maximum level (600 ohm) | |
| DVI 201 A D Tx | >+9 dBm, balanced or unbalanced at 1% THD+N |
| DVI 201 A D Rx | >+6.8 dBm, unbalanced at 1% THD+N |
|
| Control/remote — external device (pass-through) |
|---|
| Serial control port input | |
| Transmitter | RS-232 via (1) 3.5 mm, 3 pole captive screw connector |
| Receiver | 1 set of proprietary signals on a female RJ-45 jack |
| Serial control port output | |
| Transmitter | 1 set of proprietary signals on a female RJ-45 jack |
| Receiver | RS-232 via a 3.5 mm, 3 pole captive screw connector |
| NOTE | Protocol is mirrored between the transmitter and the receiver. |
|
| Serial control pin configurations | Captive screw connectors: 1 = Tx, 2 = Rx, 3 = GND |
|
| General |
|---|
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts |
| Power consumption | |
| DVI 201 A D Tx | 3.0 watts, 12 VDC |
| DVI 201 A D Rx | 4.2 watts, 12 VDC |
| NOTE | Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the CAT 5/5e/6 or Extron STP201 cable. |
|
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, no vents |
| Mounting | |
| Furniture or wall mount | Yes, with a 1 gang wall box or mud ring |
| Enclosure type | Metal |
| Enclosure dimensions | |
| Faceplate | 2.6" H* x 1.3" W x 0.1" D
(6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang decorator-style wallplate.)
*Overall height is 4.1" (10.4 cm) including mounting tabs. Mounting holes are 3.8" [9.5 cm] apart on center. |
| Buffer | 2.7" H x 1.8" W x 0.75" D
(6.9 cm H x 4.6 cm W x 1.9 cm D)
(Depth excludes connectors.) |
| Product weight | 0.5 lbs (0.3 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE**, C-tick, FCC Class A**, ICES, VCCI |
| NOTE | **CE and FCC testing is conducted with STP (shielded twisted pair) cable. |
|
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (CMS-041017-D23) |