| DTP T 3G-SDI 230 D |
|
| Video |
|---|
| Signal Type | SDI: NTSC @ 59.94 Hz, PAL @ 50 Hz;
HD-SDI: 720p @ 25, 29.97, 30, 50, 59.94, 60 Hz; 1035i @ 50, 59.94, 60 Hz;
1080i @ 50, 59.94, 60 Hz; 1080p @ 24, 30 Hz;
3G-SDI: 1080p @ 50, 59.94, 60 Hz (4:2:2); 1080i @ 50, 59.94, 60 Hz (4:2:2);
720p @ 24, 25, 50, 59.94, 60 Hz (4:2:2) |
| Data rates | 270 Mbps, 1.485 Gbps, 2.97 Gbps |
| Standards | SMPTE-259M, SMPTE-292M, SMPTE-424M, SMPTE-272M, SMPTE-299M, ITU-RBT.601,
ITU-RBT.1120 |
|
| Video input |
|---|
| Number/signal type | 1 single link SDI, HD-SDI, or 3G-SDI digital component video |
| Connectors | 1 female BNC |
| Equalization | Automatic, up to 300' (100 m) for 3G-SDI |
|
| Audio — pertaining to DTP |
|---|
| Gain | Unbalanced output: 0 dB (from receiver), balanced output: +6 dB (from receiver) |
| Frequency response | 20 Hz to 20 kHz, ±1 dB |
| THD + Noise | 0.03% @ 1 kHz, 0.3% @ 20 kHz at nominal level |
| S/N | >90 dB at maximum output (unweighted) |
| Stereo channel separation | >80 dB |
| Digital sampling rate | 48 kHz |
| Bit Depth | 16 bit |
|
| Audio input |
|---|
| Number/signal type | 1 stereo, unbalanced |
| NOTE | Analog audio is not embedded onto the digital video signal. Analog audio and digital embedded audio are transmitted simultaneously and output on the receiver on two different connectors. |
|
| Connectors | 1 female, 3.5mm, stereo jack, 2 channel; tip (L), ring (R), sleeve (Gnd) |
| Impedance | >10k ohms, DC coupled |
| Nominal level | -10 dBV (316 mVrms) |
| Maximum level | +7 dBV, unbalanced |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output |
|---|
| Signal Type | DTP 230 |
| Connector | 1 female RJ-45 |
|
| Interconnection between transmitter and receiver |
|---|
| Connectors | 1 female RJ-45 per unit for 1 cable connecting the transmitter and receiver |
| Termination standards | TIA/EIA T568B |
| DTP signal | |
| Signal transmission distance | Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable |
| Cable requirements | Solid conductor, 24 AWG or better |
| Cable recommendations | 400 MHz bandwidth STP cable |
| NOTE | Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
|
| Communications — external device (RS-232/IR over TP) |
|---|
| NOTE | Protocol is mirrored between the connected DTP 230 or DTP 330 endpoints and the "Over TP" ports on the
DTP T 3G-SDI 230 D. Signals from a control device pass into each "Over TP" port, are embedded with the DTP signal, and sent to the individual DTP 230 Tx or Rx endpoints for control of remote sink or source devices. The "Over TP" ports are simply pass-through connections to DTP endpoints. |
|
| Serial control port | Bidirectional RS-232 control via (1) 3.5 mm, 5-pole captive screw connector
(connector is shared with IR control port) |
| Baud rates | 300 to 38.4k baud |
| Protocol | Data bits = 8 or 7
Stop bits = 1 or 2
Parity = none
|
| Serial control pin configuration | Captive screw connectors: 1 = Tx, 2 = Rx, 3 = Gnd |
| IR control port | Bidirectional IR control via (1) 3.5 mm, captive screw connector, 5-pole
(connector is shared with RS-232 control port)
TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz |
| IR control pin configuration | 3 = Gnd, 4 = IR Tx, 5 = IR Rx |
| USB control port | 1 front panel female mini USB B |
| USB standards | USB 2.0, low speed |
| Program control | Extron Simple Instruction Set (SIS™) |
|
| General |
|---|
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power consumption | |
| Device | 8.9 watts, 12 VDC |
| Device and power supply | 10.8 watts, 100-240 VAC, 50-60 Hz |
| NOTE | Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable. |
|
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, no vents |
| Thermal dissipation | |
| Device | 12.5 BTU/hr |
| Device and power supply | 19.1 BTU/hr |
| Mounting | |
| Furniture or wall mount | Yes, with a 1 gang wall box or mud ring |
| Enclosure type | Metal |
| Enclosure dimensions | |
| Faceplate | 2.6" H x 1.3" W x 0.1 " D
(6.6 cm H x 3.3 cm W x 0.3 cm D) |
| Device | 2.7" H x 1.7" W x 1.6" D
(6.9 cm H x 4.3 cm W x 4.0 cm D) |
| Product weight | 1 lbs (0.5 kg) |
| Regulatory compliance | AS/NZS, c-UL, C-tick, CE**, FCC Class A**, ICES, UL |
| NOTE | **CE and FCC testing is conducted with STP cable. |
|
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (4380-092818) |