DTP HDMI 4K 230 Txツイストペアトランスミッターは1本のシールド付きCATxアケーブルを使用して、HDMI、オーディオ、双方向RS-232およびIR制御信号を最長70m伝送可能です(1080p) 。また、アナログステレオオーディオ入力をデジタル化し、同じCATxケーブルで同時に伝送することが可能です。最大4K解像度に対���します。さらに、EDIDおよびHDCPのDDC通信をソース機器とディスプレー間で維持、機器間の互換性を確実にし最適な信号を伝送します。これらの機能に加えて、コンパクトな筐体サイズでトランスミッターまたはレシーバーのいずれか一方から他方に電源供給が可能なため設置場所を選ばず、スペースに制限がある環境でHDMI、オーディオおよび双方向制御信号を延長する用途に最適です。

仕様

DTP HDMI 230 4K Tx/Rx
specification
Frame rate1	24, 25, 30, 50, or 60 fps
Chroma sampling1	4:4:4, 4:2:2, or 4:2:0
Color bit depth1	8 bits per color
Signal Type	HDMI 1.4, HDCP 2.3
Max. video data rate	10.2 Gbps (3.4 Gbps per color)
NOTE     1Subject to the maximum data rate limit. Use our calculator (www.extron.com/8Kdatarate) to determine video parameters supported by this data rate.
NOTE     This product consists of a transmitter (DTP HDMI 4K 230 Tx) and a receiver (DTP HDMI 4K 230 Rx), sold separately, with twisted pair cables linking the transmitter and receiver.
NOTE     *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output.
Video
Maximum data rate	10.2 Gbps (3.4 Gbps per color)
Maximum pixel clock	300 MHz
Resolution range	Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz, 4K/UHD @ 60 Hz with 4:2:0 chroma subsampling (* reduced blanking)
Color bit depth	8, 10, or 12 bits — subject to the maximum data rate limit
Formats	RGB and YCbCr digital video
Standards	DVI 1.0, HDMI 1.4, HDCP 2.3, CEA-861E
Video Input — transmitter
Number/signal type	1 single link HDMI (or DVI-D*)
Connectors	1 female HDMI type A
Interconnection Between Transmitter and Receiver
Connectors	1 female RJ-45 per unit
Termination standard	TIA/EIA T568B
Signal transmission distance
1080p @ 60 Hz	Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
2560x1600 @ 60 Hz	Up to 130' (40 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
4K/UHD @ 30Hz and 60 Hz	Up to 130' (40 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable
Cable requirements	Solid conductor, 24 AWG or better
Cable recommendations	400 MHz bandwidth, STP (shielded twisted pair)
NOTE     Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance.
Video Output — receiver
Number/signal type	1 single link HDMI (or DVI-D*)
Connectors	1 female HDMI type A
Audio
Gain	Unbalanced output: 0 dB; balanced output +6 dB
Frequency response	20 Hz to 20 kHz, ±0.5 dB
THD + Noise	0.03% @ 20 Hz to 20 kHz at maximum output
S/N	>90 dB, at maximum output (15 dBu), balanced (unweighted)
Stereo channel separation	>80 dB @ 1 kHz to 20 kHz
Audio input
Number/signal type	1 PC level stereo, unbalanced
NOTE     Analog audio is not embedded onto the digital video signal.  Embedded digital audio is not de-embedded from the digital video signal.
Connectors	(1) 3.5 mm stereo jack, 2 channel; tip (L), ring (R), sleeve (ground)
Impedance	>10k ohms, DC coupled
Nominal level	-10 dBV (316 mVrms)
Maximum level	+7 dBV (unbalanced)
NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
Audio output
Number/signal type	1 stereo (2 channel), balanced/unbalanced
Connectors	(1) 3.5 mm captive screw connector, 5 pole
Impedance	50 ohms unbalanced, 100 ohms balanced
Gain error	±0.1 dB channel to channel
Maximum level (600 ohm)	>+11 dBu, balanced
Control/remote — external device (pass-through, unidirectional or bidirectional)
Serial control port input/output
Transmitter	RS-232 via (1) 3.5 mm, 5 pole captive screw connector for RS-232 control (±5 V) (connector is shared with IR control port)
Receiver	1 set of proprietary signals on a female RJ-45 jack
Serial control port output/input
Transmitter	1 set of proprietary signals on a female RJ-45 jack
Receiver	RS-232 via a 3.5 mm, 3 pole captive screw connector
Baud rate and protocol	300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity
Serial control pin configuration	1 = Tx, 2 = Rx, 3 = Gnd
IR control port	(1) 3.5 mm, captive screw connector, 5 pole (connector is shared with RS-232 control port) TTL level (0 to 5 V) modulated infrared control from 30 kHz up to 60 kHz
IR control pin configuration	3 = Gnd, 4 = IR Tx, 5 = IR Rx
General
Power supply	External Input: 100-240 VAC, 50-60 Hz Output: 12 VDC, 1.5 A, 18 watts
Power consumption
Transmitter
Device	2.5 watts
Device and power supply	3.4 watts
Remote power budget	12 watts
Receiver
Device	4.2 watts
Device and power supply	5.8 watts
Remote power budget	12 watts
NOTE     Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable.
Ambient temperature/humidity	Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling	Convection, no vents
Thermal dissipation
Transmitter
Device	7.4 BTU/hr
Device and power supply	10.4 BTU/hr
Receiver
Device	13.0 BTU/hr
Device and power supply	18.7 BTU/hr
Mounting
Rack mount	Yes, with optional 1U high rack shelf
Furniture mount	Yes, with optional under-desk mounting kit
Enclosure type	Metal
Enclosure dimensions
Transmitter	1.0" H x 4.3" W x 3.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 7.6 cm D) (Depth excludes connectors.)
Receiver	1.0" H x 4.3" W x 6.0" D (quarter rack wide) (2.5 cm H x 10.9 cm W x 15.2 cm D) (Depth excludes connectors.)
Product weight
Transmitter	0.5 lbs (0.3 kg)
Receiver	1.0 lb (0.5 kg)
Regulatory compliance	CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI, Complies with the appropriate requirements of RoHS, WEEE UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply.
NOTE     **CE and FCC testing is conducted with STP (shielded twisted pair) I/O cable.
Product warranty	3 years parts and labor
Everlast power supply warranty	7 years parts and labor
NOTE     All nominal levels are at ±10%.
NOTE     Specifications are subject to change without notice.
(5453-D20)

梱包時の寸法および質量
製品番号	高さ	幅	奥行き	質量
60-1271-12	7.6 cm	20.3 cm	27.9 cm	0.72 kg