FOX 3G HD-SDI

FOX 3G HD-SDI MM

1. Provide a fiber optic transceiver that shall support the long-haul transmission of 3G-SDI, HD-SDI, and SDI signals
   1. Long distance signal extension of single link 3G-SDI/HD-SDI/SDI digital video signals over multimode fiber optic cabling
   2. Video input requirements
      1. Shall provide one (1) BNC connector for single link 3G-SDI/HD-SDI/SDI digital video signals
      2. Shall support data rates from 270 Mbps to 2.97 Gbps
      3. Shall comply with SMPTE 259M, 292M, 424M, and ITU digital video standards
      4. Shall pass all data allowed within published SMPTE and ITU digital video standards, including embedded audio, ancillary ID and metadata information, and SDTI, SMPTE 305M, and HD-SDTI, SMPTE 348M, digital video signals
      5. Shall provide automatic input cable equalization for up to -30 dB of cable loss
   3. Audio input requirements
      1. Shall support embedded AES audio on BNC input connector
   4. Video output requirements
      1. Shall provide two (2) buffered BNC connectors for single link 3G-SDI/HD-SDI/SDI digital video signals
      2. Shall support data rates from 270 Mbps to 2.97 Gbps
      3. Shall comply with SMPTE 259M, 292M, 424M, and ITU digital video standards
      4. Shall pass all data allowed within published SMPTE and ITU digital video standards, including embedded audio, ancillary ID and metadata information, and SDTI, SMPTE 305M, and HD-SDTI, SMPTE 348M, digital video signals
      5. Shall provide automatic reclocking on buffered outputs to reshape and restore digital signals
         1. Reclocking for 270 Mbps, 1.485 Gbps, 2.97 Gbps data rates
         2. Reclocking is bypassed for non-standard data rates
   5. Audio output requirements
      1. Shall support embedded AES audio on BNC output connector
   6. Interconnection requirements
      1. Shall provide interconnection between transceivers over multimode fiber optic cabling
      2. Shall provide two (2) LC-type fiber optic connectors for interconnection between transceivers
   7. Transmission requirements
      1. Shall support extension of single link 3G-SDI/HD-SDI/SDI digital video signals over multimode fiber optic cabling
      2. Shall provide a fiber optic signal transmission distance capability of 2 km (1.25 miles) over OM3 or OM4 laser optimized multimode fiber optic cabling
      3. Shall support an optical loss budget of at least 7 dB between transceiver and receiver
   8. Power requirements
      1. Shall be equipped with an external, universal AC power supply capable of supporting 100 – 240 VAC, 50/60 Hz power
   9. Setup, control, and configuration requirements
      1. Shall support three modes of operation
         1. Bidirectional transceiver mode
         2. Transmitter with local monitor outputs mode
         3. Receiver with daisy-chaining mode
      2. Shall provide two (2) DIP switches on rear panel for mode selection
   10. Bidirectional transceiver mode requirements
       1. Shall accept a 3G-SDI/HD-SDI/SDI signal on the BNC input for transmission along the fiber optic cable via the fiber optic output Tx port
       2. Shall accept a 3G-SDI/HD-SDI/SDI signal on the fiber optic input Rx port that is made available on the two (2) buffered BNC output connectors
   11. Transmitter with local monitor outputs mode requirements
       1. Shall accept a 3G-SDI/HD-SDI/SDI signal on the BNC input for transmission along the fiber optic cable via the fiber optic Tx port
       2. Shall provide the input signal as local outputs on the two (2) buffered BNC output connectors
   12. Receiver with daisy-chaining mode requirements
       1. Shall accept a 3G-SDI/HD-SDI/SDI signal on the fiber optic input Rx port that is made available on the number two (2) buffered BNC output connector
       2. Shall support daisy-chaining to allow multiple units to support displays at multiple locations
          1. Fiber optic output Tx port provides a loop-out for the incoming signal on the fiber optic input Rx port for transmission along fiber optic cable to another destination
          2. BNC input connector and number one (1) BNC output connector is not used when configured as a receiver with daisy chaining
   13. General requirements
       1. Shall provide visual signal on LED indicators located on front panel for video data rate and power
       2. Shall provide visual signal on LED indicators located on rear panel for link status
       3. Shall have a 1” (2.5 cm) high, quarter rack width mountable metal enclosure
       4. Shall be rack mountable with optional rack shelf
       5. Shall be pole or furniture mountable with optional mounting kits
       6. Shall meet regulatory compliance
          1. CE, c-UL, UL
          2. CE, C-tick, FCC Class A, ICES, VCCI
          3. Appropriate requirements of RoHS, WEEE
       7. Shall provide at least three (3) years parts and labor warranty
       8. Shall be compatible with Extron FOX Series distribution amplifiers
       9. Shall be compatible with Extron FOX Matrix Switchers for signal distribution systems up to 1000x1000 and larger
   14. Approved device shall be the Extron FOX 3G HD-SDI MM (60-900-01); no alternates or equals