最近閲覧した製品
2LC OM4 MM P
コンサルタント向け資料
製品番号を選択してください:
テキストをコピー
コピーされました！
エラーが発生しました。しばらくしてからもう一度お試しください。
2LC OM4 MM P/1
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a one (1) meter (3.3 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/1 (part number 26-671-01), no alternates or equals
2LC OM4 MM P/1
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a one (1) meter (3.3 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/1 (part number 26-671-01), no alternates or equals
2LC OM4 MM P/2
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a two (2) meter 6.6 (foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/2 (part number 26-671-02), no alternates or equals
2LC OM4 MM P/2
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a two (2) meter 6.6 (foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/2 (part number 26-671-02), no alternates or equals
2LC OM4 MM P/3
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a three (3) meter (9.8 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/3 (part number 26-671-03), no alternates or equals
2LC OM4 MM P/3
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a three (3) meter (9.8 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/3 (part number 26-671-03), no alternates or equals
2LC OM4 MM P/5
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a five (5) meter (16.4 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/5 (part number 26-671-05), no alternates or equals
2LC OM4 MM P/5
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a five (5) meter (16.4 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/5 (part number 26-671-05), no alternates or equals
2LC OM4 MM P/10
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a ten (10) meter (32.8 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/10 (part number 26-671-10), no alternates or equals
2LC OM4 MM P/10
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a ten (10) meter (32.8 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/10 (part number 26-671-10), no alternates or equals
2LC OM4 MM P/15
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a fifteen (15) meter (49.2 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/15 (part number 26-671-15), no alternates or equals
2LC OM4 MM P/15
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a fifteen (15) meter (49.2 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/15 (part number 26-671-15), no alternates or equals
2LC OM4 MM P/20
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a twenty (20) meter (65.6 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/20 (part number 26-671-20), no alternates or equals
2LC OM4 MM P/20
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a twenty (20) meter (65.6 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/20 (part number 26-671-20), no alternates or equals
2LC OM4 MM P/30
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a thirty (30) meter (98.4 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/30 (part number 26-671-30), no alternates or equals
2LC OM4 MM P/30
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a thirty (30) meter (98.4 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/30 (part number 26-671-30), no alternates or equals
2LC OM4 MM P/40
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a forty (40) meter (131 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/40 (part number 26-671-40), no alternates or equals
2LC OM4 MM P/40
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a forty (40) meter (131 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/40 (part number 26-671-40), no alternates or equals
2LC OM4 MM P/50
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a fifty (50) meter (164 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/50 (part number 26-671-50), no alternates or equals
2LC OM4 MM P/50
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a fifty (50) meter (164 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/50 (part number 26-671-50), no alternates or equals
2LC OM4 MM P/60
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a sixty (60) meter (197 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/60 (part number 26-671-60), no alternates or equals
2LC OM4 MM P/60
- Provide interconnection for the transmission of high-speed optical digital signals over a duplex multimode fiber optic cable assembly
- Duplex multimode fiber optic cable assembly for transmission of optical digital signals
- Cable construction requirements
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Glass fiber core diameter of 50 µm
- Glass fiber outer diameter of 125 µm
- Shall provide a 900 µm tight buffer coating surrounding each glass fiber
- Shall provide Aramid yarn as the strengthening material surrounding each tight-buffered fiber
- Shall provide a 2 mm diameter, OFNP plenum-rated jacket to meet NEC, CSA, and ICEA safety standards, surrounding each tight-buffered fiber and Aramid yarn strengthening material
- Shall provide duplex zip-cord cable construction for strength and protection of the glass fiber
- Shall provide two (2) 50/125 µm graded-index, bend-insensitive, laser-optimized multimode fibers
- Termination requirements
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Pre-polished with an UPC – ultra physical contact end face
- Shall be configured with duplex connectors using AB - BA reverse-pair polarity as described in TIA-568
- Shall be terminated at each end with an industry-standard LC-type fiber optic connector
- Performance requirements
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- TIA 492-AAAD
- IEC 60793-2-10, A1a.3
- ISO/IEC 11801, OM4
- Shall provide attenuation of less than 3.0 dB per kilometer at an 850 nm wavelength
- Shall provide attenuation of less than 1.2 dB per kilometer at a 1300 nm wavelength
- Shall provide an insertion loss of less than 0.5 dB per 300 meters at 850 nm or 1300 nm
- Shall provide minimum effective mode bandwidth of 4700 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 3500 MHz-km at an 850 nm wavelength
- Shall provide minimum overfill launch bandwidth of 550 MHz-km at a 1300 nm wavelength
- Shall be bend-insensitive fiber for a tight bend radius of 0.3 inches (7.5 mm) with minimal cable losses
- Shall meet or exceed OM4 laser-optimized multimode fiber performance standards
- General requirements
- Shall be available in a sixty (60) meter (197 foot) length
- Shall provide an outer dimeter of 0.08" ±0.008" (2.0 mm ±0.2 mm)
- Shall meet regulatory compliance
- ETL/c-ETL OFNP FT6 (plenum rated)
- Shall provide a lifetime limited performance warranty
- Approved cable shall be Extron 2LC OM4 MM P/60 (part number 26-671-60), no alternates or equals
アイテムをカートに追加する
Order Message Number
製品番号
注: Extron products using the Universal AC Outlet accept a number of different AC plug types. Before use, ensure that the device meets all regulatory requirements for your region and complies with all applicable local safety and electrical codes and standards.
現在の合計金額:
Annotation Graphics Processor
To view this page ensure that Adobe Flash Player version
11.0.0 or greater is installed and enabled.
製品をEメールでシェア
2LC OM4 MM P
レーザー最適化2芯マルチモード光ファイバーケーブル（LC-LC、防煙加工）
Eメールアドレスを正しく入力してください。
ありがとうございます。Emailの送信が完了しました。
Eメール送信中にエラーが発生しました。しばらくしてからもう一度お試しください。
Chrome
Firefox
Edge
Safari